Let's solve the mystery of commit bf1178c9 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()").  Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.

Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational.  This time is specced as 0 - 200
ms.  The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.

Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted.  That very closely matches the magic 70 ms
delay that we had.  ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).

To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!).  This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)".  Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms.  The extra 100 ms
(presumably) comes from this part in the datasheet:

> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.

Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").

If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it.  Given
the silly debouncing in the bridge chip, though, it seems unlikely.

One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up.  In theory that would let me detect _exactly_ when I could
continue and do link training.  Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors.  Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: NSean Paul <sean@poorly.run>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org

If the HPD signal isn't hooked up to this panel we need a 200 ms
delay.  In the datasheet this is shown as the maximum time that HPD
will take to be asserted after power is given to the panel.
Reviewed-by: NSean Paul <sean@poorly.run>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-3-dianders@chromium.org

Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.

However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up.  In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.

Let's add support in simple-panel for this concept.

At the moment we will co-opt the existing "prepare" delay to keep
track of the delay and we'll use a boolean to specify that a given
panel should only apply the delay if the "no-hpd" property was
specified.
Reviewed-by: NSean Paul <sean@poorly.run>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-2-dianders@chromium.org

Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.

However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up.  In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.

Let's add a property in the device tree for this concept.
Reviewed-by: NSean Paul <sean@poorly.run>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-1-dianders@chromium.org

BOE panel (ID: 0x0771) that reports "DFP 1.x compliant TMDS".
But it's 6bpc panel only instead of 8 bpc.

Add panel ID to edid quirk list and set 6 bpc as default to
work around this issue.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: NLee, Shawn C <shawn.c.lee@intel.com&gt;>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540792173-7288-1-git-send-email-shawn.c.lee@intel.com

Merge tag 'drm-intel-next-fixes-2018-10-18' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Fix GPU hang on MacBook2,1 when booting in EFI mode (Bugzilla #105637)
- Fix garbled console on Y tiled BIOS framebuffer configs (Bugzilla #108264)
- Fix black screen on certain eDP panels eg. Dell XPS 9350 (Bugzilla #107489 and #105338)
- MST fixes that Rodrigo dropped from drm-intel-fixes and bunch of Icelake fixes
- Then assorted proactive code fixes caught by CI or developers
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018165725.GA2281@jlahtine-desk.ger.corp.intel.com

Add missing MODULE_FIRMWARE while loading DMC ICL.

v2: Add Fixes tag. (Rodrigo)
v3: Rebase by Rodrigo after commit 7fe78985 ("drm/i915/csr:
 restructure CSR firmware definition macros")
v4: Rodrigo fixing his own mess on commit mentioning on v3
    comment above.

Fixes: 4445930f ("firmware/dmc/icl: load v1.07 on icelake.")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v2)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004223613.19938-1-rodrigo.vivi@intel.com
(cherry picked from commit 00e5d8b1)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Since when it was introduced we forgot to add
this case so ICL was using a wrong signal_levels
as reference.

Fixes: fb5c8e9d ("drm/i915/icl: Implement voltage swing programming sequence for Combo PHY DDI")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NManasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017215652.26841-1-rodrigo.vivi@intel.com
(cherry picked from commit 61cdfb9e)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

DDI/TC clock-off bits are not equally distanced. TC1-3 bits are
from offset 12 & TC4 is at offset 21.
Create a function to choose correct clk-off bit.

v2: Add fixes tag (Lucas)

Fixes: c27e917e ("drm/i915/icl: add basic support for the ICL clocks")
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016023752.9285-1-lucas.demarchi@intel.com
(cherry picked from commit bb1c7edc)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

This patch creates a function/wrapper to check if port is combophy port
instead of explicitly comparing ports.

Changes since V1:
 - keep all intel_port_is_* helper together (Lucas)
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004085043.10154-1-mahesh1.kumar@intel.com
(cherry picked from commit 176597a1)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Fixes for 4.20.  Highlights:
- VCN DPG fixes for Picasso
- Add support for the latest vega20 vbios
- Scheduler timeout fix
- License fixes for radeon and amdgpu
- Misc other fixes
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017215427.2804-1-alexander.deucher@amd.com

Merge tag 'drm-misc-next-fixes-2018-10-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

- Add quirk to fix orientation of Acer One 10 (S1003) panel (Hans)

Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181017200741.GA240649@art_vandelay

If BIOS configured a Y tiled FB we failed to set up the backing object
tiling accordingly, leading to a lack of GT fence installed and a
garbled console.

The problem was bisected to
commit 011f22eb ("drm/i915: Do NOT skip the first 4k of stolen memory for pre-allocated buffers v2")
but it just revealed a pre-existing issue.

Kudos to Ville who suspected a missing fence looking at the corruption
on the screen.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: <ronald@innovation.ch>
Cc: <stable@vger.kernel.org>
Reported-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: <ronald@innovation.ch>
Tested-by: <ronald@innovation.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108264
Fixes: bc8d7dff ("drm/i915/skl: Provide a Skylake version of get_plane_config()")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016160011.28347-1-imre.deak@intel.com
(cherry picked from commit 914a4fd8)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Handle integer overflow when computing the sub-page length for shmem
backed pread/pwrite.
Reported-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012140228.29783-1-chris@chris-wilson.co.uk
(cherry picked from commit a5e856a5)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

For mmap-exhaustion, we deliberately put the system under a large amount
of pressure to ensure that we are able to reap mmap-offsets from dead
objects. If background activity does that reaping for us, that defeats
the purpose of the test and in some cases will fail our sanity checks
(because of the fake activity we use to prevent the idle worker).

Fixes: 932cac10 ("drm/i915/selftests: Prevent background reaping of acti
ve objects")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181011103748.18387-1-chris@chris-wilson.co.uk
(cherry picked from commit 0b4bf7ca)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This patch fixes the original commit c0cfb10d ("drm/i915/edp:
Do not do link training fallback or prune modes on EDP") that causes
a blank screen in case of certain eDP panels (Eg: seen on Dell XPS13 9350)
where first link training fails and a retraining is required by falling
back to lower link rate/lane count.
In case of some panels they advertise higher link rate/lane count
than whats required for supporting the panel's native mode.
But we always link train at highest link rate/lane count for eDP
and if that fails we can still fallback to lower link rate/lane count
as long as the fallback link BW still fits the native mode to avoid
pruning the panel's native mode yet retraining at fallback values
to recover from a blank screen.

v3:
* Add const for fixed_mode (Ville)
v2:
* Send uevent if link failure on eDP unconditionally

Fixes: c0cfb10d ("drm/i915/edp: Do not do link training fallback or prune modes on EDP")
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.17+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107489
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105338Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Tested-by: NAlexander Wilson <alexander.wilson@ncf.edu>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009212804.702-1-manasi.d.navare@intel.com
(cherry picked from commit 1e712535)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Currently, i915 appears to rely on blocking modesets on
no-longer-present MSTB ports by simply returning NULL for
->best_encoder(), which in turn causes any new atomic commits that don't
disable the CRTC to fail. This is wrong however, since we still want to
allow userspace to disable CRTCs on no-longer-present MSTB ports by
changing the DPMS state to off and this still requires that we retrieve
an encoder.

So, fix this by always returning a valid encoder regardless of the state
of the MST port.

Changes since v1:
- Remove mst atomic helper, since this got replaced with a much simpler
  solution
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-6-lyude@redhat.com
(cherry picked from commit a9f9ca33)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Since we need to be able to allow DPMS on->off prop changes after an MST
port has disappeared from the system, we need to be able to make sure we
can compute a config for the resulting atomic commit. Currently this is
impossible when the port has disappeared, since the VCPI slot searching
we try to do in intel_dp_mst_compute_config() will fail with -EINVAL.

Since the only commits we want to allow on no-longer-present MST ports
are ones that shut off display hardware, we already know that no VCPI
allocations are needed. So, hardcode the VCPI slot count to 0 when
intel_dp_mst_compute_config() is called on an MST port that's gone.

Changes since V4:
- Don't use mst_port_gone at all, just check whether or not the drm
  connector is registered - Daniel Vetter
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-5-lyude@redhat.com
(cherry picked from commit f67207d7)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Currently we set intel_connector->mst_port to NULL to signify that the
MST port has been removed from the system so that we can prevent further
action on the port such as connector probes, mode probing, etc.
However, we're going to need access to intel_connector->mst_port in
order to fixup ->best_encoder() so that it can always return the correct
encoder for an MST port to prevent legacy DPMS prop changes from
failing. This should be safe, so instead keep intel_connector->mst_port
always set and instead just check the status of
drm_connector->regustered to signify whether or not the connector has
disappeared from the system.

Changes since v2:
- Add a comment to mst_port_gone (Jani Nikula)
- Change mst_port_gone to a u8 instead of a bool, per the kernel bot.
  Apparently bool is discouraged in structs these days
Changes since v4:
- Don't use mst_port_gone at all! Just check if the connector is
  registered or not - Daniel Vetter
Signed-off-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181008232437.5571-4-lyude@redhat.com
(cherry picked from commit 6ed5bb1f)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Before we can reset the seqno, we have to be sure the engines are idle.
In debugfs/i915_drop_caches_set, we do wait_for_idle but allow ourselves
to be interrupted. We should only proceed to reset the seqno then if we
were not interrupted, and so also avoid overwriting the error status.

References: https://bugs.freedesktop.org/show_bug.cgi?id=108133
Fixes: 6b048706 ("drm/i915: Forcibly flush unwanted requests in drop-caches")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181004082119.24970-1-chris@chris-wilson.co.uk
(cherry picked from commit 88a83f3c)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

When we decide that a plane is attached to the wrong pipe we try
to turn off said plane. However we are passing around the crtc we
think that the plane is supposed to be using rather than the crtc
it is currently using. That doesn't work all that well because
we may have to do vblank waits etc. and the other pipe might
not even be enabled here. So let's pass the plane's current crtc to
intel_plane_disable_noatomic() so that it can its job correctly.

To do that semi-cleanly we also have to change the plane readout
to record the plane's visibility into the bitmasks of the crtc
where the plane is currently enabled rather than to the crtc
we want to use for the plane.

One caveat here is that our active_planes bitmask will get confused
if both planes are enabled on the same pipe. Fortunately we can use
plane_mask to reconstruct active_planes sufficiently since
plane_mask still has the same meaning (is the plane visible?)
during readout. We also have to do the same during the initial
plane readout as the second plane could clear the active_planes
bit the first plane had already set.

v2: Rely on fixup_active_planes() to populate active_planes fully (Daniel)
    Add Daniel's proposed comment to better document why we do this
    Drop the redundant intel_set_plane_visible() call

Cc: stable@vger.kernel.org # fcba862e8428 drm/i915: Have plane->get_hw_state() return the current pipe
Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Cc: Daniel Vetter <daniel@ffwll.ch>
Tested-by: NDennis <dennis.nezic@utoronto.ca>
Tested-by: NPeter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003145017.4527-1-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 62358aa4)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Plane sanitation needs vblank interrupts (on account of CxSR disable).
So let's restore vblank interrupts earlier.

v2: Make it actually build
v3: Add comment to explain why we need this (Daniel)

Cc: stable@vger.kernel.org
Cc: Dennis <dennis.nezic@utoronto.ca>
Tested-by: NDennis <dennis.nezic@utoronto.ca>
Tested-by: NPeter Nowee <peter.nowee@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105637
Fixes: b1e01595 ("drm/i915: Redo plane sanitation during readout")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003144951.4397-1-ville.syrjala@linux.intel.com
(cherry picked from commit 68bc30de)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

commit 4e0b83a5 ("drm/i915: Extract per-platform plane->check()
functions") removed the plane max stride check for sprite planes.
I was going to add it back when introducing GTT remapping for the
display, but after further thought it seems better to re-introduce
it separately.

So let's add the max stride check back. And let's do it in a nicer
form than what we had before and do it for all plane types (easy
now that we have the ->max_stride() plane vfunc).

Only sprite planes really need this for now since primary planes
are capable of scanning out the current max fb size we allow, and
cursors have more stringent stride checks elsewhere.

Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 4e0b83a5 ("drm/i915: Extract per-platform plane->check() functions")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918140243.12207-1-ville.syrjala@linux.intel.comReviewed-by: NDhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
(cherry picked from commit fc3fed5d)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

ret_code should be initialized with 0. The check of read/write
ptr should be activate when UVD_POWER_STATUS_TILES is off.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The Acer One 10 uses a clamshell design with a detachable keyboard.
As such in normal operating mode, with the keyboard attach the device
is in landscape mode (and the Acer logo at boot also shows in landscape
mode).

But the device uses a portrait screen rotated 90 degrees (sigh). This
commit adds a quirk for this device so that we shown the fbcon the
right way up and that we hint userspace to also show e.g. plymouth and
gdm the right way up.

Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012101610.29100-1-hdegoede@redhat.com

The error handling is wrong and "ent" could be NULL we when dereference
it to get "ent->d_inode".

The thing is that normally debugfs_create_file() is not supposed to
require (or have) any error handling.  That function does return error
pointers if debugfs is turned off but we know it's enable here.  When
it's enabled, then it returns NULL on error.

So what I did was I stripped out all the error handling except around
the i_size_write().  I could have just used a NULL check instead of an
IS_ERR_OR_NULL() but I figured this was more clear because that way you
don't have to look at the surrounding code to see whether debugfs is
enabled or not.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add mmDB_DEBUG3 settings.
Signed-off-by: NFeifei Xu <Feifei.Xu@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Update the PPtable structure to fit the latest SMC firmware.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

PPTABLE structure is stretched to add I2C controller
configuration. Hold on the PPTABLE_V20_SMU_VERSION bump
until the VBIOS is ready.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update SDMA golden settings.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

fix a typo in for loop: i->j
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
A loop inside of build_evenly_distributed_points function that traverse through
the array of points become an infinite loop when m_GammaUpdates does not
get assigned to any value.

[How]
In DMColor, clear m_gammaIsValid bit just before writting all Zeromem for
m_GammaUpdates, to prevent calling build_evenly_distributed_points
before m_GammaUpdates gets assigned to some value.
Signed-off-by: NSu Sung Chung <Su.Chung@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Commit b2441318 added
"SPDX-License-Identifier: GPL-2.0" to files which previously had no
license, change this to MIT for radeon matching the license text of the
other radeon files.
Signed-off-by: NJonathan Gray <jsg@jsg.id.au>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Commit b2441318
'License cleanup: add SPDX GPL-2.0 license identifier to files with no license'
incorrectly added "SPDX-License-Identifier: GPL-2.0" to a file with MIT
license text.  Change the SPDX identifier to match the license text.
Signed-off-by: NJonathan Gray <jsg@jsg.id.au>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Update Static Power Gate mode UVD status clear
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Set VCPU busy after gate power during vcn Static Power Gate start
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Apply new UMC enable for VNC Dynamic Power Gate mode
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Remove Sitatic Power Gate mode unused steps during vcn start
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add Static Power Gate mode Register XX check
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Move Static Power Gate mode mc resume after MPC control
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Acked-by: NLeo Liu <leo.liu@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>