Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:

struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)

Compile tested only.

Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Acked-by: NAntonio Quartulli <a@unstable.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fm10k_open requires rtnl_lock to be held.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update every header file and other locations to consistently use
Intel(R) instead of just Intel. Also update copyright year of files
which we modified.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fm10k_io_error_detected() does not need to call pci_disable_device(). In
the cases where the reset needs to occur, the stack flow will result in
calling fm10k_remove() which already disables the PCI device. If we
leave the pci_disable_device(), we result in a warning about disabling
an already disabled device.

Many PCI drivers do call pci_disable_device() in their .error_detected()
routines, but it does not appear to be required. In addition, these
drivers have a check "is_pci_enabled()" call in their remove routines,
which is how they chose to handle the duplicate device disable.

This seems incorrect, since the PCI device structure is reference
counted. It is very possible that the reference count for the PCI device
could be greater than 1. In this case, you would remove the PCI device
within the error_detected routine, reducing count to 1, then remove it
again in the remove function, reducing it to zero. This would result in
yet another disable somewhere else failing. Thus, we shouldn't be using
is_pci_enabled() to check for this issue. Instead, just remove the
extraneous pci_device_disable() found within the error_detected routine.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, any error responses from the switch manager after an
LPORT_MAP request are silently ignored. At most the mailbox message will
be reported as an error. This can result in unexpected behavior when the
switch manager has configured a port with zero bandwidth. Add support
for reading the fm10k_swapi_error structure from LPORT_MAP responses.

If the message contains the necessary TLV and has a non-zero error code,
report link down, clear the dglort_map, and delay the next
get_host_state call by a reasonable delay. Also log an error message
indicating that the LPORT_MAP request failed.

The delay ensures preventing an interrupt storm on the switch manager,
and reduces the number of mailbox messages we send in this scenario
drastically.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 1588 support within fm10k does not work correctly with the current
version of the switch management software, and likely never worked
correctly to begin with. Remove support for PTP/1588. Update copyright
year for all these files while we're touching them.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During an AER action response, we were calling fm10k_close without
holding the rtnl_lock() which could lead to possible RCU warnings being
produced due to 64bit stat updates among other causes. Similarly, we
need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the
same pattern elsewhere in the driver and protect the entire open/close
sequence.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

s/funciton/function to resolve a typo, and cleanup grammar on a few
comments regarding processing the VF mailboxes.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Delay initialization of the service timer and service task until late
probe. If we don't wait, failures in probe do not properly cleanup the
service timer or service task items, which results in the kernel panic
below, potentially freezing the whole system. In addition, ensure that
the SERVICE_DISABLE bit is set before we request the MBX IRQ since the
MBX interrupt attempts to schedule the service task otherwise. This
prevents a similar trace from occurring after this change.

We didn't notice this issue before because probe almost always completes
successfully. I discovered it due to a mis-ordered mailbox handler
array, which resulted in the following failure when requesting mailbox
interrupt.

[  555.325619] ------------[ cut here ]------------
[  555.325628] WARNING: CPU: 0 PID: 4941 at lib/list_debug.c:33 __list_add+0xa0/0xd0()
[  555.325631] list_add corruption. prev->next should be next (ffffffff81f46648), but was           (null). (prev=ffff8807fad5d0e8).
<snip>
[  555.325722] CPU: 0 PID: 4941 Comm: insmod Tainted: G           OE   4.0.4-303.fc22.x86_64 #1
[  555.325725] Hardware name: Intel Corporation S2600CO/S2600CO, BIOS SE5C600.86B.02.03.8x23.060520140825 06/05/2014
[  555.325727]  0000000000000000 00000000b4f161b3 ffff88081a21f8e8 ffffffff81783124
[  555.325734]  0000000000000000 ffff88081a21f940 ffff88081a21f928 ffffffff8109c66a
[  555.325740]  0000000064000000 ffff8807fad5d0e8 ffff8807fad5d0e8 ffffffff81f46648
[  555.325746] Call Trace:
[  555.325752]  [<ffffffff81783124>] dump_stack+0x45/0x57
[  555.325757]  [<ffffffff8109c66a>] warn_slowpath_common+0x8a/0xc0
[  555.325759]  [<ffffffff8109c6f5>] warn_slowpath_fmt+0x55/0x70
[  555.325763]  [<ffffffff813ba270>] __list_add+0xa0/0xd0
[  555.325768]  [<ffffffff81102d1d>] __internal_add_timer+0x9d/0x110
[  555.325771]  [<ffffffff81102dbf>] internal_add_timer+0x2f/0xc0
[  555.325774]  [<ffffffff81104e5a>] mod_timer+0x12a/0x230
[  555.325782]  [<ffffffffa03d54ca>] fm10k_probe+0x69a/0xc80 [fm10k]
[  555.325787]  [<ffffffff813e8355>] local_pci_probe+0x45/0xa0
[  555.325791]  [<ffffffff8129cf42>] ? sysfs_do_create_link_sd.isra.2+0x72/0xc0
[  555.325794]  [<ffffffff813e96b9>] pci_device_probe+0xf9/0x150
[  555.325799]  [<ffffffff814d7e73>] driver_probe_device+0xa3/0x400
[  555.325802]  [<ffffffff814d82ab>] __driver_attach+0x9b/0xa0
[  555.325805]  [<ffffffff814d8210>] ? __device_attach+0x40/0x40
[  555.325808]  [<ffffffff814d5bd3>] bus_for_each_dev+0x73/0xc0
[  555.325811]  [<ffffffff814d78ce>] driver_attach+0x1e/0x20
[  555.325815]  [<ffffffff814d7480>] bus_add_driver+0x180/0x250
[  555.325819]  [<ffffffffa03b2000>] ? 0xffffffffa03b2000
[  555.325823]  [<ffffffff814d8aa4>] driver_register+0x64/0xf0
[  555.325826]  [<ffffffff813e7bec>] __pci_register_driver+0x4c/0x50
[  555.325832]  [<ffffffffa03d6ca3>] fm10k_register_pci_driver+0x23/0x30 [fm10k]
[  555.325838]  [<ffffffffa03b2080>] fm10k_init_module+0x80/0x1000 [fm10k]
[  555.325843]  [<ffffffff81002128>] do_one_initcall+0xb8/0x200
[  555.325848]  [<ffffffff811e10d2>] ? __vunmap+0xa2/0x100
[  555.325852]  [<ffffffff811fe239>] ? kmem_cache_alloc_trace+0x1b9/0x240
[  555.325855]  [<ffffffff8178230e>] ? do_init_module+0x28/0x1cb
[  555.325858]  [<ffffffff81782346>] do_init_module+0x60/0x1cb
[  555.325862]  [<ffffffff8112168e>] load_module+0x205e/0x26b0
[  555.325866]  [<ffffffff8111d110>] ? store_uevent+0x70/0x70
[  555.325870]  [<ffffffff812234b0>] ? kernel_read+0x50/0x80
[  555.325873]  [<ffffffff81121f3e>] SyS_finit_module+0xbe/0xf0
[  555.325878]  [<ffffffff81789749>] system_call_fastpath+0x12/0x17
[  555.325880] ---[ end trace 9e0f58d071eafd2a ]---
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use BIT() macro instead.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When comparing MAC addresses, use ether_addr_equal instead of memcmp to
ETH_ALEN length. Found and replaced using the following sed:

 sed -e 's/memcmp\x28\(.*\), ETH_ALEN\x29/!ether_addr_equal\x28\1\x29/'
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to cleanup the exception handling for the paths where
we reset the interrupts and then reconfigure them.  In all of these paths
we had very different levels of exception handling.  I have updated the
driver so that all of the paths should result in a similar state if we
fail.

Specifically the driver will now unload the mailbox interrupt, free the
queue vectors and MSI-X, and then detach the interface.

In addition for any of the PCIe related resets I have added a check with
the hw_ready function to just make sure the registers are in a readable
state prior to reopening the interface.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Similar to ixgbe and i40e, initialize XPS on driver load so that we can
take advantage of this kernel feature.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses two issues.

First is the fact that the fm10k_mbx_free_irq was assuming msix_entries was
valid and that will not always be the case.  As such we need to add a check
for if it is NULL.

Second is the fact that we weren't freeing the IRQ if the mailbox API
returned an error on trying to connect.
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of using lowercase vlan, vid, or VID, always use VLAN or VLAN ID
in comments when referring to VLANs. The original driver code was
consistent, but recent patches have not been as consistent with this
naming scheme.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Avoid the use of CamelCase for some variable names that previously
slipped through review.
Reported-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The existing adaptive ITR algorithm is overly restrictive. It throttles
incorrectly for various traffic rates, and does not produce good
performance. The algorithm now allows for more interrupts per second,
and does some calculation to help improve for smaller packet loads. In
addition, take into account the new itr_scale from the hardware which
indicates how much to scale due to PCIe link speed.
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Reported-by: NAlex Duyck <alexander.duyck@gmail.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The init_hw function may fail, and in the case of VFs, it might change
the number of maximum queues available. Thus, for every flow which
checks init_hw, we need to ensure that we clear the queue scheme before,
and initialize it after. The fm10k_io_slot_reset path will end up
triggering a reset so fm10k_reinit needs this change. The
fm10k_io_error_detected and fm10k_io_resume also need to properly clear
and reinitialize the queue scheme.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent change modified init_hw in some flows the function may fail on
VF devices. For example, if a VF doesn't yet own its own queues.
However, many callers of init_hw didn't bother to check the error code.
Other callers checked but only displayed diagnostic messages without
actually handling the consequences.

Fix this by (a) always returning and preventing the netdevice from going
up, and (b) printing the diagnostic in every flow for consistency. This
should resolve an issue where VF drivers would attempt to come up
before the PF has finished assigning queues.

In addition, change the dmesg output to explicitly show the actual
function that failed, instead of combining reset_hw and init_hw into a
single check, to help for future debugging.

Fixes: 1d568b0f6424 ("fm10k: do not assume VF always has 1 queue")
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't change netdev hw_features later in fm10k_probe, instead set all
values inside fm10k_alloc_netdev. To do so, we need to know the MAC type
(whether it is PF or VF) in order to determine what to do. This helps
ensure that all logic regarding features is co-located.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The fm10k_msix_clean_rings function runs from hard interrupt context or
with interrupts already disabled in netpoll.

It can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: NAlexander Duyck <aduyck@mirantis.com>
Tested-by: NKrishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a private ethtool flag to enable display of these statistics, which
are generally less useful. However, sometimes it can be useful for
debugging purposes. The most useful portion is the ability to see what
the PF thinks the VF mailboxes look like.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This comment is no longer true due to a couple of mailbox locking
refactors, and we now don't actually do any rtnl protected operations
directly in the mailbox path. Remove this comment as it is factually
incorrect and confusing.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Modify behavior of Malicious Driver Detection events. Presently, the
hardware disables the VF queues and re-assigns them to the PF. This
causes the VF in question to continuously Tx hang, because it assumes
that it can transmit over the queues in question. For transient events,
this results in continuous logging of malicious events.

New behavior is to reset the LPORT and VF state, so that the VF will
have to reset and re-enable itself. This does mean that malicious VFs
will possibly be able to continue and attempt malicious events again.
However, it is expected that system administrators will step in and
manually remove or disable the VF in question.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch ensures that VLAN traffic on the default VID will go to the
corresponding VLAN device if it exists. To do this, mask the rx_ring VID
if we have an active VLAN on that VID.

For this to work correctly, we need to update fm10k_process_skb_fields
to correctly mask off the VLAN_PRIO_MASK bits and compare them
separately, otherwise we incorrectly compare the priority bits with the
cleared flag. This also happens to fix a related bug where having
priority bits set causes us to incorrectly classify traffic.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds the MAC address to the list of values recorded on driver
load.  The MAC address represents the serial number of the unit and allows
us to track the value should a card be replaced in a system.

The log message should now be similar in output to that of ixgbe.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the netdev permanent address during fm10k_reinit enables the user
to immediately see the new MAC address on the VF even if the device
isn't up. The previous code required that the device by opened before
changes would appear.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is useful in cases where we connect to a slot at Gen3, but the slot
is behind a bus which only connected at Gen2. This generally only
happens when a PCIe switch is in the sequence of devices, and can be
very confusing when you see slow performance with no obvious cause.

I am aware this patch has a few lines that break 80 characters, but
there does not seem to be a readable way to format them to less than 80
characters. Suggestions welcome.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The service task reads some registers as part of its normal routine,
even while the interface is down. Normally this is ok. However, during
suspend we have disabled the PCI device. Due to this, registers will
read in the same way as a surprise-remove event. Disable the service
task while we suspend, and re-enable it after we resume. If we don't do
this, the device could be UP when you suspend and come back from resume
as closed (since fm10k closes the device when it gets a surprise
remove).
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>