Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: NRahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: NRahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Whenever firmware indicates that there's an async indication it needs
to handle, there's a switch-case where the right functionality is called
based on function's personality and information.

Before iWARP is added [as yet another client], switch over the SPQ into
a callback-registered mechanism, allowing registration of the relevant
event-processing logic based on the function's personality. This allows
us to tidy the code by removing protocol-specifics from a common file.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VFs are currently not mapping their doorbell bar, instead relying
on the small doorbell window they have in their limited regview bar.

In order to increase the number of possible Tx connections [queues]
employeed by VF past 16, we need to start using the doorbell bar if
one such is exposed - VF would communicate this fact to PF which would
return the size-bar internally configured into chip, according to
which the VF would decide whether to actually utilize the doorbell
bar.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the infrastructure for supporting VFs that want to open
multiple transmission queues on the same queue-zone.
At this point, there are no VFs that actually request this functionality,
but later patches would remedy that.

 a. VF and PF would communicate the capability during ACQUIRE;
    Legacy VFs would continue on behaving as they do today

 b. PF would communicate number of supported CIDs to the VF
    and would enforce said limitation

 c. Whenever VF passes a request for a given queue configuration
    it would also pass an associated index within said queue-zone
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the infrastructure a PF maintains for each one of its VFs
to support multiple queue-cids on a single queue-zone.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now we used to have a single VF legacy compatibility mode,
one that affected the place of the Rx producers of those VFs [mostly].

As PF would soon support allocating CIDs for VFs instead of having
a static CID<->queue configuration for them, we'll need to have
an additional legacy mode since existing VFs would need to continue
on using the older mode of operation.

Change the infrastrucutre so that the legacy would be able to indicate
which of the legacy behaviors is needed for a given VF.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a queue-cid is allocated, assign an index inside that's
CID's queue-zone.

For PFs and VFS, this number is going to be unique and derive
from a per-queue-zone bitmap, while for PF's VFs queues the
number is currently going to constant; Later, we'd add the
capability of a VF to communicate such an index to its PF.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're going to need additional information for queue-cids
that a PF creates for its VFs, so start by refactoring existing
logic used for initializing said struct into receiving a structure
encapsulating the VF-specific information that needs to be provided.

This also introduces QED_QUEUE_CID_SELF - each queue-cid would hold
an indication to whether it belongs to the hw-function holding it
[whether that's a PF or a VF], or else what's the VF id it belongs
to.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we're resetting the IGU CAM each time we initialize the PF
device, there's no need to reset the VF SBs again when initializing
IOV.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IOV code is very intrusive in its manipulation of the status block
database.
Add a new auxiliary function to allow the PF to find an available unused
status block to configure for a specific VF's MSI-x vector.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a first step for relaxing various assumptions done by driver
about the IGU mapping, the driver is now going to read the entire
IGU into a shadow copy, and mark in its database each status block
that's relevant for it.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The QL41xxx adapters' PCI allows a single configuration for the
MSI-x table size of all child VFs of a given PF.
The existing code wouldn't cause the management firmware to set
that value, meaning the VFs would retain the default MSI-x table
size.

Introduce a new scheme so that whenever a VF is enabled, driver
would set the number of MSI-x to be the maximum over the various
VFs' needs.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flows configuring tunnel ports in HW use the main_ptt which should
be reserved for core-functionality.
Signed-off-by: NManish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add these misspellings to scripts/spelling.txt too

Link: http://lkml.kernel.org/r/962aace119675e5fe87be2a88ddac1a5486f8e60.1490931810.git.joe@perches.comSigned-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.

Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: NManish Chopra <manish.chopra@cavium.com>
Signed-off-by: NYuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link information exists only on the leading hwfn,
but some of its derivatives [e.g., min/max rate] need to
be configured for each hwfn.
When re-basing the VF link view, use the leading hwfn
information as basis for all existing hwfns to allow
said configurations to stick.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Malicious VF existance should be interesting enough for the
hyperuser. Change the PF indication that one of its child VF
became malicious to appear by default.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF<->VF interface allows for the VF to request
multiple queues closure via a single message, but this has
never been used by any official driver.

We now deprecate this option, forcing each queue close
to arrive via a different command; This would be required
for future TLVs that are going to extend the queue TLVs with
additional information on a per-queue basis.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PF needs to validate the status of VF queues before asking firmware
to configure anything for them, but that validation is done in various
different forms - sometimes inadequate.

Add auxillary functions that can be used for testing of the queue
state and convert the various flows to use those instead of current
existing flows; Also, add missing validations where needed.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When starting the VF's vport, the PF would first configure
the status blocks of the VF and then reset them.
That would cause some of the configured information to be lost -
specifically it would mean that all the VFs queues would use
the Rx coalescing state-machine of the status block.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF responds to the VF requests it also cleans the HW-channel
indication in firmware to allow further VF messages to arrive,
but the order currently applied is wrong -
The PF is copying by DMAE the response the VF is polling on for
completion, and only afterwards sets the HW-channel to ready state.

This creates a race condition where the VF would be able to send
an additional message to the PF before the channel would get ready
again, causing the firmware to consider the VF as malicious.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a VF is considered malicious, driver handling of the VF
FLR flow would clean said indication - but not if the FLR is
part of an sriov-disable flow.
That leads to further issues, as PF wouldn't re-enable the
previously malicious VF when sriov is re-enabled.

No reason for that - simply clean malicious indications in
the sriov-disable flow as well.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.

It also adds 2 new PCI device-IDs to qede:
  - 0x8070 for QL41xxx PFs
  - 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A PF syncronizes all IOV activity relating to its VFs
by using a single workqueue handling the work.
The workqueue would reach a bitmask of pending VF events
and act upon each in turn.

Problem is that the indication of a VF message [which sets
the 'vf event' bit for that VF] arrives and is set in
the slowpath attention context, which isn't syncronized with
the processing of the events.
When multiple VFs are present, it's possible that PF would
lose the indication of one of the VF's pending evens, leading
that VF to later timeout.

Instead of adding locks/barriers, simply move from a bitmask
into a per-VF indication inside that VF entry in the PF database.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF learns of the current link state via its bulletin board,
which might reflect either the physical link state or some
user-configured logical state.
Whenever the physical link changes or whnever such a configuration
is explicitly made by user the PF driver would update the bulletin
that the VF reads. But if neither has happened - i.e., PF still
hasn't got a physical link up and no additional configuration was
done the VF wouldn't have a valid link information available.

Simply reflect the physical link state whenever the VF is
initialized. The user could then affect it however he wants.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero. Also, it makes the code clearer
Signed-off-by: NShyam Saini <mayhs11saini@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trusted VFs would be allowed to receive promiscuous and
multicast promiscuous data.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.

This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.

This patch re-organizes the way L2 queues are configured and maintained.
In short:
  - Required parameters for queue init are now well-defined.
  - Qed would allocate a queue-cid based on parameters.
    Upon initialization success, it would return a handle to caller.
  - Queue-handle would be maintained by entity requesting queue-init,
    not necessarily qed.
  - All further queue-APIs [update, destroy] would use the opaque
    handle as reference for the queue instead of various indices.

The possible owners of such handles:
  - PF queues [qede] - complete handles based on provided configuration.
  - VF queues [qede] - fw-context-less handles, containing only relative
    information; Only the PF-side would need the absolute indices
    for configuration, so they're omitted here.
  - VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver sets several restrictions about the number of supported VFs
according to available HW/FW resources.
This creates a problem as there are constellations which can't be
supported [as limitation don't accurately describe the resources],
as well as holes where enabling IOV would fail due to supposed
lack of resources.

This introduces a new interal feature - vf-queues, which would
be used to lift some of the restriction and accurately enumerate
the queues that can be used by a given PF's VFs.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Malicious VFs might be caught in several different methods:
  - Misusing their bar permission and being blocked by hardware.
  - Misusing their fastpath logic and being blocked by firmware.
  - Misusing their interaction with their PF via hw-channel,
    and being blocked by PF driver.

On the first two items, firmware would indicate to driver that
the VF is to be considered malicious, but would sometime still
allow the VF to communicate with the PF [depending on the exact
nature of the malicious activity done by the VF].
The current existing logic on the PF side lacks handling of such events,
and might allow the PF to perform some incorrect configuration on behalf
of a VF that was previously indicated as malicious.

The new scheme is simple -
Once the PF determines a VF is malicious it would:
 a. Ignore any further requests on behalf of the VF-driver.
 b. Prevent any configurations initiated by the hyperuser for
    the malicious VF, as firmware isn't willing to serve such.

The malicious indication would be cleared upon the VF flr,
after which it would become usable once again.
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the backbone required for the various HW initalizations
which are necessary for the qedr driver - FW notification, resource
initializations, etc.
Signed-off-by: NRam Amrani <Ram.Amrani@caviumnetworks.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We get a few warnings when building kernel with W=1:
drivers/net/ethernet/qlogic/qed/qed_l2.c:112:5: warning: no previous prototype for 'qed_sp_vport_start' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:110:6: warning: no previous prototype for 'qed_iov_is_valid_vfid' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:188:5: warning: no previous prototype for 'qed_iov_post_vf_bulletin' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:578:6: warning: no previous prototype for 'qed_iov_set_vfs_to_disable' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1135:28: warning: no previous prototype for 'qed_iov_get_public_vf_info' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:1148:6: warning: no previous prototype for 'qed_iov_clean_vf' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2444:5: warning: no previous prototype for 'qed_iov_chk_ucast' [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qed/qed_sriov.c:2762:5: warning: no previous prototype for 'qed_iov_vf_flr_cleanup' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>