[WHY]
dram clock change latencies get updated using ddr4 latency table, but
that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.

[HOW]
Update latency from 23.84 to 11.72.
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NJake Wang <haonan.wang2@amd.com>
Reviewed-by: NSung Lee <Sung.Lee@amd.com>
Acked-by: NAnson Jacob <anson.jacob@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

From Ard:

"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.

So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."

Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: NWill Deacon <will@kernel.org>
Reported-by: NArd Biesheuvel <ardb@kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Kernel test robot throws below warning ->

drivers/gpu/drm/amd/amdgpu/../display/dc/dcn21/dcn21_dccg.c:46:6:
warning: no previous prototype for 'dccg21_update_dpp_dto'
[-Wmissing-prototypes]

Adding prototype for dccg21_update_dpp_dto().
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
New value breaks VSR on high refresh panels, reverting until a fix is developed
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
dram clock change latencies get updated using ddr4 latency table, but
does that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.

[HOW]
Update latency from 23.84 to 11.72.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Cached backlight is never being updated since panel_cntl specific
registers were moved from abm to panel_cntl.

[How]
Update cached backlight in set_abm_immediate_disable as what we used to
do. Also, update the priority of backlight restore mechanism so that
cached backlight has the highest priority since it is always correct.
Signed-off-by: NCamille Cho <Camille.Cho@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
If the system does not have hostvm enabled, disabling it for
DML validation will allow more modes to pass at lower voltage
levels.

[How]
When initializing HostVM save state to hubbub and read back
when populating DML pipes from context.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
4K monitor shows corruption if dpp dto phase is larger than modulo.

[How]
cap phase value never larger than modulo.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Program modulo with ref dpp clk Mhz/10.
Program phase with pipe dpp clk Mhz /10.
DMUB FW could use these value to determine optimization clk
for PSR power saving.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When mpo enabled, video comes is 709. Desktop use sRGB.
So color change easily noticeable especially when switch between
mpo/non-mpo.

[How]
Force use sRGB for video TF is sRGB or BT709.
DCN1/DCN2 use predefined type with YUV.
DCN3 use distributed points type with YUV.
Signed-off-by: NJing Zhou <Jing.Zhou@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Due to the freesync power optimization increasing vtotal, the driver
believes that MPO is supported. MPO is turned on. Freesync then
exits, MPO can no longer be supported and immediate flip fails. This
causes corruption on the panel.

[How]
Avoid the freesync optimization when doing validation so in the case
freesync exits, driver can still support the configuration.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In some cases, prefetch mode 0 is unsupported but prefetch 1 is
supported. Due to previous change always forcing prefetch mode to 0, we
are failing bandwidth validation in cases where we should not.

[How]
By default try prefetch mode 0 but in the case validation fails, attempt
to do prefetch mode 1 to see if it is supported.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Acked-by: NBindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Prior commit "Blank HUBP during pixel data blank for DCN30"
missed the call to set_disp_pattern_generator from
set_crtc_test_pattern, which re-exposed the issue for which
we initially blocked active-only p-state switching.

[How]
 - remove dcn30_blank_pixel_data, set dcn30 back to dcn20 version
 - new hwss funciton set_disp_pattern_generator
 - dcn20 version just calls opp_set_disp_pattern_generator
 - dcn30 version implements the HUBP blank
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
On APU should be always using prefetch mode 0.
Currently, sometimes prefetch mode 1 is being
used causing system to hard hang due to
minTTUVBlank being too low.

[How]
Any ASIC running DCN21 will by default allow
self refresh and mclk switch. This sets both
min and max prefetch mode to 0 by default.
Signed-off-by: NIsabel Zhang <isabel.zhang@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We should leave GSL if we're not doing immediate flip no matter if
we're doing pipe split or not

[How]
Check for updating GSL state whenever we're not doing
immediate flip

v2: Squash in build fix (Alex)
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some sink devices wish to have access to the minimum
HBlank supported by the ASIC.

[How]
Make the ASIC minimum HBlank available in Source
Device information address 0x340.
Signed-off-by: NAshley Thomas <Ashley.Thomas2@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY & HOW]
Enable ODM Combine + Fullscreen MPO on DCN2.1
For lower power consumption in video use cases.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why&How]
Create a separate dcn21_fast_validate_bw function for dcn21.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
DF PState and Voltage State are coupled such that one cannot be
raised without raising the other. This uses more power than
is necessary in high bandwidth scenarios.

[HOW]
Add logic to create a new bounding box state that allows for
DF PState to be low while Voltage State is high. Watermarks
vlevel calculation logic was also udpated to assume
state 1 contains the new optimized state.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Currently construction of clock limits gets skipped for diags.
This logic would be useful to get tested in diags.

[HOW]
Copy existing states to clk_table such that update_bw_bounding_box
logic gets used to fill the table.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
HDCP 1.4 failed on SL8800 SW w/a test driver use.

[how]
Slow down the HW i2c speed when used by HW i2c.
This request: each acquired_i2c_engine setup the i2c speed needed
and sets the I2c engine for HDCP use at release_engine.

This covers SW using HW i2c engine and HDCP using HW i2c engine.
for dmcu using HW i2c engine, needs add similar logic in dmcu fw.
Signed-off-by: NCharlene Liu <Charlene.Liu@amd.com>
Reviewed-by: NChris Park <Chris.Park@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
enable ODM on eDP panel with ABM will result in color difference
on the panel due to only one ABM module to set one pipe.

[How]
Block ABM in case of ODM enabled on eDP.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.

[How]
Power off eDP backlight before power off eDP
Signed-off-by: NPeikang Zhang <peikang.zhang@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Disable triplebuffering by default.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Current pipe merge and split logic only supports cases where new
dc_state is allocated and relies on dc->current_state to gather
information from previous dc_state.

Calls to validate_bandwidth on UPDATE_TYPE_MED would cause an issue
because there is no new dc_state allocated, and data in
dc->current_state would be overwritten during pipe merge.

[how]
Only allow validate_bandwidth when new dc_state space is created.
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: NDaniel Kolesa <daniel@octaforge.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of  the  pipe programming sequence to prevent this.

[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Caused pipe split regression
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Each asic can optimize best based on its capabilities

[How]
Optimizing timing for a new pixel clock
Signed-off-by: NReza Amini <Reza.Amini@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The only usage of dcn21_res_pool_funcs is to assign its address to a
const pointer. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: NRikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of  the  pipe programming sequence to prevent this.

[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: NAlvin Lee <alvin.lee2@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Each asic can optimize best based on its capabilities

[How]
Optimizing timing for a new pixel clock
Signed-off-by: NReza Amini <Reza.Amini@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NEryk Brol <eryk.brol@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Implement an interface to obtain plane size caps

[How]
Add min_width, min_height fields to dc_plane_cap structure.
Set values to 16x16 for discrete ASICs, and 64x64 for others.
Signed-off-by: NIgor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
dcn20_add_dsc_to_stream_resource is accessed in amdgpu_dm directly.
This creates build error for configuration with DCN disabled.

[How]
Make the function available through a resource pool function so
that dcn20 function need not be called directly.
Signed-off-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies.  Powering down
hardware on boot will ensure SW state is accurate.

[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DP link layer CTS specs updated to change the test parameters in test
4.2.1.1.
Before it requires source to delay 400us on aux no reply.
With the specs updates Errata5, it requires source to delay 3.2ms
(based on LTTPR aux timeout)
This causes our test to fail after updating with the latest test
equipment firmware.

[how]
the change is to allow LTTPR 3.2ms aux timeout delay by default.
And set back to 400us if LTTPR feature is not enabled.
We will set 3.2ms and always enable LTTPR non transparent mode
if LTTPR feature is enabled and LTTPR is present.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
DMUB command table should be allowed to be used
only if dmcu is explicitly disabled.
Signed-off-by: NAurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
The change causes some regression in a common use case.
Will need more investigation before fixing the original issue.

[how]
This reverts commit fb8cf277.
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
SOC_BOUNDING_BOX_VALID is unused and not required for dcn21.

[How]
Remove it.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
dal side nv12 wa has a lot of side effects.
KMD side wa is used, so this should be remove.

[How]
Removed wa from dal side.
Signed-off-by: NYongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>