[WHY]
dram clock change latencies get updated using ddr4 latency table, but
that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.

[HOW]
Update latency from 23.84 to 11.72.
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NJake Wang <haonan.wang2@amd.com>
Reviewed-by: NSung Lee <Sung.Lee@amd.com>
Acked-by: NAnson Jacob <anson.jacob@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The ip discovery is supported on green sardine, it doesn't need gpu info
firmware anymore.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NPrike Liang <Prike.Liang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

[WHY]
Previously as MPO + ODM Combine was not supported, finding secondary pipes
for each case was mutually exclusive. Now that both are supported at the same
time, both cases should be taken into account when finding a secondary pipe.

[HOW]
If a secondary pipe cannot be found based on previous bottom pipe,
search for a second pipe using next_odm_pipe instead.
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NAnson Jacob <anson.jacob@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

[Why]
Find out when we try to disable CRC calculation, crc generation is still
enabled. Main reason is that dc_stream_configure_crc() will never get
called when the source is AMDGPU_DM_PIPE_CRC_SOURCE_NONE.

[How]
Add checking condition that when source is
AMDGPU_DM_PIPE_CRC_SOURCE_NONE, we should also call
dc_stream_configure_crc() to disable crc calculation.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit c920888c.

Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Bindu R <Bindu.R@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NWayne Lin <Wayne.Lin@amd.com>
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 6ae09fa4.

Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Bindu R <Bindu.R@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit f01afd1e.

Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Bindu R <Bindu.R@amd.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Add function to set power brake sequence.
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Reviewed-by: NKenneth Feng <kenneth.feng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add DID 0x164C into pciidlist under CHIP_RENOIR family.
Signed-off-by: Nmengwang <mengbing.wang@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

Add green_sardine PCI id support and map it to renoir asic type.

v2: add apu flag
Signed-off-by: NPrike Liang <Prike.Liang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

This patch is to update atomfirmware parser for the memory type and
bandwidth of DDR5 and DDR4.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The address of the GOLDEN_TSC_COUNT_UPPER/GOLDEN_TSC_COUNT_LOWER for
Vnagogh are different from the others.

The offset of the GOLDEN_TSC_COUNT_UPPER for Vangogh is 0x0025 by
calculation.
The offset of the GOLDEN_TSC_COUNT_LOWER for Vangogh is 0x0026 by
calculation.
Signed-off-by: Nchen gong <curry.gong@amd.com>
Acked-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

KASAN reported a slab-out-of-bounds read of size 1 in
kdf_create_vcrat_image_cpu().

This occurs when, for example, when on an x86_64 with a single NUMA node
because kfd_fill_iolink_info_for_cpu() is a no-op, but afterwards the
sub_type_hdr->length, which is out-of-bounds, is read and multiplied by
entries. Fortunately, entries is 0 in this case so the overall
crat_table->length is still correct.

Check if there were any entries before de-referencing sub_type_hdr which
may be pointing to out-of-bounds memory.

Fixes: b7b6c385 ("drm/amdkfd: Calculate CPU VCRAT size dynamically (v2)")
Suggested-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NJeremy Cline <jcline@redhat.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

commit a861736d ("drm/amd/display: Fixed Intermittent blue screen on OLED panel")

causes power regression for many users. It seems that this change causes
the MCLK to get forced high; this creates a regression for many users
since their devices were not able to drop to a low state after this
change. For this reason, this reverts commit
a861736d.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1407
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Naveed Ashfaq <Naveed.Ashfaq@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Roman Li <roman.li@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
The initial purpose of dcn10 pipe split is to support some high
bandwidth mode which requires dispclk greater than max dispclk. By
initial bring up power measurement data, it showed power consumption is
less with pipe split for dcn block. This could be reason for enable pipe
split by default. By battery life measurement of some Chromebooks,
result shows battery life is longer with pipe split disabled.

[How]
Disable pipe split by default. Pipe split could be still enabled when
required dispclk is greater than max dispclk.
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NHersen Wu <hersenxs.wu@amd.com>
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NRoman Li <Roman.Li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Required for DSC MST
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NZhan Liu <Zhan.Liu@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
The stack variable "val" is potentially unpopulate it, so initialize it
with the value 0xf (indicating an invalid mux)
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In dc_link_dp_set_test_pattern, we assume all pipes have a stream, which
can cause null pointer dereference.

[How]
Add a null pointer check before accessing stream.
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NRodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

psp GFX_CTRL_CMD_ID_CONSUME_CMD different for windows and linux,
according to psp, linux cmds are not correct.

v2: only correct GFX_CTRL_CMD_ID_CONSUME_CMD.
Signed-off-by: NVictor Zhao <Victor.Zhao@amd.com>
Reviewed-by: NEmily.Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This fix bug 210921 where DRM_INFO floods log when hitting an unsupported ASIC in
amdgpu_device_asic_has_dc_support(). This info should be only called once.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210921Signed-off-by: NAlexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This reverts commit a135a1b4.

This leads to blank screens on some boards after replugging a
display.  Revert until we understand the root cause and can
fix both the leak and the blank screen after replug.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211033
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1427
Cc: Stylon Wang <stylon.wang@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Andre Tomt <andre@tomt.net>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

From Ard:

"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.

So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."

Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: NWill Deacon <will@kernel.org>
Reported-by: NArd Biesheuvel <ardb@kernel.org>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

added I2C address and asic support flag
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

old code wrongly used the bad page status as the function return value,
which cause amdgpu_ras_badpages_read always return failed.
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NGuchun Chen <guchun.chen@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Navi12 HDCP & DTM deinitialization needs continue to free bo if already
created though initialized flag is not set.
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NJiawei Gu <Jiawei.Gu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Some of the newly added code is hidden inside of #ifdef
blocks, but one variable is unused when debugfs is disabled:

drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8370:8: error: unused variable 'configure_crc' [-Werror,-Wunused-variable]

Change the #ifdef to an if(IS_ENABLED()) check to fix the warning
and avoid adding more #ifdefs.

Fixes: c920888c ("drm/amd/display: Expose new CRC window property")
Reviewed-by: NWayne Lin <Wayne.Lin@amd.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to improve the fine grain tuning function for RV/RV2/PCO.
The fine grain tuning function uses the sysfs node -- pp_od_clk_voltage
to config gfxclk. Meanwhile, another sysfs
node -- power_dpm_force_perfomance_level also affects the gfx clk.
It will cause confusion when these two sysfs nodes works
together. So this patch adds one flag to avoid this confusion, the flag
will make these two sysfs nodes work separately.
The flag is set as "disabled" by default, so the fine grain tuning function
will be disabled by default.
Only when power_dpm_force_perfomance_level is changed to
"manual" mode, the flag will be set as "enabled",
and the fine grain tuning function will be enabled.
In other profile modes, including "auto", "high", "low",
"profile_peak", "profile_standard", "profile_min_sclk",
"profile_min_mclk", the flag will be set as "disabled",
and the od range of fine grain tuning function will
be restored default value.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to fix the failure when change power profile to
"profile_peak" for renoir.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When GFXOFF is enabled and GPU is idle, driver will fail to access some
registers. Therefore change to disable power gating before all access
registers with MMIO.

Dmesg log is as following:
amdgpu 0000:03:00.0: amdgpu: amdgpu: finishing device.
amdgpu: cp queue pipe 4 queue 0 preemption failed
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
amdgpu 0000:03:00.0: amdgpu: failed to write reg 2890 wait reg 28a2
amdgpu 0000:03:00.0: amdgpu: failed to write reg 1a6f4 wait reg 1a706
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ASD and TA share the same firmware in SIENNA_CICHLID and only TA
firmware is requested during boot, so only need release TA firmware when
remove device.

[   83.877150] general protection fault, probably for non-canonical address 0x1269f97e6ed04095: 0000 [#1] SMP PTI
[   83.888076] CPU: 0 PID: 1312 Comm: modprobe Tainted: G        W  OE     5.9.0-rc5-deli-amd-vangogh-0.0.6.6-114-gdd99d5669a96-dirty #2
[   83.901160] Hardware name: System manufacturer System Product Name/TUF Z370-PLUS GAMING II, BIOS 0411 09/21/2018
[   83.912353] RIP: 0010:free_fw_priv+0xc/0x120
[   83.917531] Code: e8 99 cd b0 ff b8 a1 ff ff ff eb 9f 4c 89 f7 e8 8a cd b0 ff b8 f4 ff ff ff eb 90 0f 1f 00 0f 1f 44 00 00 55 48 89 e5 41 54 53 <4c> 8b 67 18 48 89 fb 4c 89 e7 e8 45 94 41 00 b8 ff ff ff ff f0 0f
[   83.937576] RSP: 0018:ffffbc34c13a3ce0 EFLAGS: 00010206
[   83.943699] RAX: ffffffffbb681850 RBX: ffffa047f117eb60 RCX: 0000000080800055
[   83.951879] RDX: ffffbc34c1d5f000 RSI: 0000000080800055 RDI: 1269f97e6ed04095
[   83.959955] RBP: ffffbc34c13a3cf0 R08: 0000000000000000 R09: 0000000000000001
[   83.968107] R10: ffffbc34c13a3cc8 R11: 00000000ffffff00 R12: ffffa047d6b23378
[   83.976166] R13: ffffa047d6b23338 R14: ffffa047d6b240c8 R15: 0000000000000000
[   83.984295] FS:  00007f74f6712540(0000) GS:ffffa047fbe00000(0000) knlGS:0000000000000000
[   83.993323] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   84.000056] CR2: 0000556a1cca4e18 CR3: 000000021faa8004 CR4: 00000000003706f0
[   84.008128] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   84.016155] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   84.024174] Call Trace:
[   84.027514]  release_firmware.part.11+0x4b/0x70
[   84.033017]  release_firmware+0x13/0x20
[   84.037803]  psp_sw_fini+0x77/0xb0 [amdgpu]
[   84.042857]  amdgpu_device_fini+0x38c/0x5d0 [amdgpu]
[   84.048815]  amdgpu_driver_unload_kms+0x43/0x70 [amdgpu]
[   84.055055]  drm_dev_unregister+0x73/0xb0 [drm]
[   84.060499]  drm_dev_unplug+0x28/0x30 [drm]
[   84.065598]  amdgpu_dev_uninit+0x1b/0x40 [amdgpu]
[   84.071223]  amdgpu_pci_remove+0x4e/0x70 [amdgpu]
[   84.076835]  pci_device_remove+0x3e/0xc0
[   84.081609]  device_release_driver_internal+0xfb/0x1c0
[   84.087558]  driver_detach+0x4d/0xa0
[   84.092041]  bus_remove_driver+0x5f/0xe0
[   84.096854]  driver_unregister+0x2f/0x50
[   84.101594]  pci_unregister_driver+0x22/0xa0
[   84.106806]  amdgpu_exit+0x15/0x2b [amdgpu]
Signed-off-by: NDennis Li <Dennis.Li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

global noretry setting is cached to gmc.noretry
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

fix NULL pointer issue when read sysfs amdgpu_current_backlight_pwm sysfs node.

Call Trace:
[  248.273833] BUG: kernel NULL pointer dereference, address: 0000000000000130
[  248.273930] #PF: supervisor read access in kernel mode
[  248.273993] #PF: error_code(0x0000) - not-present page
[  248.274054] PGD 0 P4D 0
[  248.274092] Oops: 0000 [#1] SMP PTI
[  248.274138] CPU: 2 PID: 1377 Comm: cat Tainted: G           OE     5.9.0-rc5-drm-next-5.9+ #1
[  248.274233] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 3802 03/15/2018
[  248.274641] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu]
[  248.274718] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e
0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01
[  248.274919] RSP: 0018:ffffb5ad809b3df0 EFLAGS: 00010203
[  248.274982] RAX: ffffa0f77d1c0010 RBX: ffffa0f793ae9168 RCX: 0000000000000001
[  248.275064] RDX: ffffa0f79753db00 RSI: 0000000000000001 RDI: 0000000000000000
[  248.275145] RBP: ffffb5ad809b3e00 R08: ffffb5ad809b3da0 R09: 0000000000000000
[  248.275225] R10: ffffb5ad809b3e68 R11: 0000000000000000 R12: ffffa0f793ae9190
[  248.275306] R13: ffffb5ad809b3ef0 R14: 0000000000000001 R15: ffffa0f793ae9168
[  248.275388] FS:  00007f5f1ec4d540(0000) GS:ffffa0f79ec80000(0000) knlGS:0000000000000000
[  248.275480] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  248.275547] CR2: 0000000000000130 CR3: 000000042a03c005 CR4: 00000000003706e0
[  248.275628] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  248.275708] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  248.275789] Call Trace:
[  248.276124]  ? current_backlight_read+0x24/0x40 [amdgpu]
[  248.276194]  seq_read+0xc3/0x3f0
[  248.276240]  full_proxy_read+0x5c/0x90
[  248.276290]  vfs_read+0xa7/0x190
[  248.276334]  ksys_read+0xa7/0xe0
[  248.276379]  __x64_sys_read+0x1a/0x20
[  248.276429]  do_syscall_64+0x37/0x80
[  248.276477]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[  248.276538] RIP: 0033:0x7f5f1e75c191
[  248.276585] Code: fe ff ff 48 8d 3d b7 9d 0a 00 48 83 ec 08 e8 46 4d 02 00 66 0f 1f 44 00 00 48 8d 05 71 07
2e 00 8b 00 85 c0 75 13 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 57 f3 c3 0f 1f 44 00 00 41 54 55 49 89 d4 53Hw
[  248.276784] RSP: 002b:00007ffcb1fc3f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[  248.276872] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5f1e75c191
[  248.276953] RDX: 0000000000020000 RSI: 00007f5f1ec2b000 RDI: 0000000000000003
[  248.277034] RBP: 0000000000020000 R08: 00000000ffffffff R09: 0000000000000000
[  248.277115] R10: 0000000000000022 R11: 0000000000000246 R12: 00007f5f1ec2b000
[  248.277195] R13: 0000000000000003 R14: 00007f5f1ec2b00f R15: 0000000000020000
[  248.277279] Modules linked in: amdgpu(OE) iommu_v2 gpu_sched ttm(OE) drm_kms_helper cec drm
i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt rpcsec_gss_krb5 auth_rpcgss nfsv4 nfs
lockd grace fscache nls_iso8859_1 snd_hda_codec_realtek snd_hda_codec_hdmi snd_hda_codec_generic
ledtrig_audio intel_rapl_msr intel_rapl_common snd_hda_intel snd_intel_dspcfg x86_pkg_temp_thermal
intel_powerclamp snd_hda_codec snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event mei_hdcp
coretemp snd_rawmidi snd_seq kvm_intel kvm snd_seq_device snd_timer irqbypass joydev snd input_leds soundcore
crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper rapl intel_cstate
mac_hid mei_me serio_raw mei eeepc_wmi wmi_bmof asus_wmi mxm_wmi intel_wmi_thunderbolt acpi_pad sparse_keymap
efi_pstore sch_fq_codel parport_pc ppdev lp parport sunrpc ip_tables x_tables autofs4 hid_logitech_hidpp
hid_logitech_dj hid_generic usbhid hid e1000e psmouse ahci libahci wmi video
[  248.278211] CR2: 0000000000000130
[  248.278221] ---[ end trace 1fbe72fe6f91091d ]---
[  248.357226] RIP: 0010:dc_link_get_backlight_level+0x5/0x70 [amdgpu]
[  248.357272] Code: 67 ff ff ff 41 b9 03 00 00 00 e9 45 ff ff ff d1 ea e9 55 ff ff ff 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 <48> 8b 87 30 01 00 00 48 8b 00 48 8b 88 88 03 00 00 48 8d 81 e8 01
Signed-off-by: NKevin Wang <kevin1.wang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NJohn Clements <john.clements@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.

Command guide:
echo "s level value" > pp_od_clk_voltage
        "s" - set the sclk frequency
        "level" - 0 or 1, "0" represents the min value,  "1" represents
        the max value
        "value" - the target value of sclk frequency, it should be limited in the
        safe range
echo "r" > pp_od_clk_voltage
        "r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
        "c" - commit the min and max value of sclk frequency to the system
        only after the commit command, the target values set by "s" command
        will take effect.
Example:
1)change power profile from "auto" to "manual"
        $ cat power_dpm_force_performance_level
        auto
        $ echo "manual" > power_dpm_force_performance_level
        $ cat power_dpm_force_performance_level
        manual
2)check the default sclk frequency
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
        $ echo "s 0 600" > pp_od_clk_voltage
        $ echo "s 1 1000" > pp_od_clk_voltage
        $ echo "c" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        600Mhz
        1:       1000Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
        $ echo "r" > pp_od_clk_voltage
        $ cat pp_od_clk_voltage
        OD_SCLK:
        0:        200Mhz
        1:       1400Mhz
        OD_RANGE:
        SCLK:     200MHz       1400MHz
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This patch is to correct the sensor value of power for vangogh.
Signed-off-by: NXiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.

This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.

So just initialize 'val' to zero to avoid the issue.

Fixes: 110b055b ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in  memory leak.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987Acked-by: NHarry Wentland <harry.wentland@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NStylon Wang <stylon.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This is not a scsi driver.
Reviewed-by: NNirmoy Das <nirmoy.das@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739
Fixes: 65bf2cf9 ("drm/amdgpu: utilize subconnector property for DP through atombios")
Tested-By: NKris Karas <bugs-a17@moonlit-rail.com>
Cc: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x

This can suppress the annoying but unharmful prompts.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NGuchun Chen <guchun.chen@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>