Add support for the DP83811 phy.

The DP83811 supports both rgmii and sgmii interfaces.
There are 2 part numbers for this the DP83TC811R does not
reliably support the SGMII interface but the DP83TC811S will.

There is not a way to differentiate these parts from the
hardware or register set.  So this is controlled via the DT
to indicate which phy mode is required.  Or the part can be
strapped to a certain interface.

Data sheet can be found here:
http://www.ti.com/product/DP83TC811S-Q1/description
http://www.ti.com/product/DP83TC811R-Q1/descriptionSigned-off-by: NDan Murphy <dmurphy@ti.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

do not sleep while adding or deleting udp tunnel.

Fixes: 846eac3f ("cxgb4: implement udp tunnel callbacks")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

set cntrl bits to indicate whether inner header checksum
needs to be calculated whenever the packet is an encapsulated
packet and enable supported encap features.

Fixes: d0a1299c ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

adapter->rawf_cnt was not initialized, thereby
ndo_udp_tunnel_{add/del} was returning immediately
without initializing {vxlan/geneve}_port.
Also initializes mps_encap_entry refcnt.

Fixes: 846eac3f ("cxgb4: implement udp tunnel callbacks")
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 0x50ad device id for new T5 card.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the skb_get_queue_mapping, skb_set_queue_mapping
and skb_rx_queue_recorded for skb queue_mapping in bonding
driver, but not use it directly.
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The method ndo_start_xmit is defined as returning a
netdev_tx_t, which is a typedef for an enum type,
but the implementation in this driver returns an int.
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the truncated bit is set only when 1) the mirrored packet
is larger than mtu and 2) the ipv4 packet tot_len is larger than
the actual skb->len.  This patch adds another case for detecting
whether ipv6 packet is truncated or not, by checking the ipv6 header
payload_len and the skb->len.
Reported-by: NXiaoyan Jin <xiaoyanj@vmware.com>
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: spectrum_span: Two minor adjustments

Petr says:

This patch set fixes a couple of nits in mlxsw's SPAN implementation:
two counts of inaccurate variable name and one count of unsuitable error
code, fixed, respectively, in patches #1 and #2.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENOENT is suitable when an item is looked for in a collection and can't
be found. The failure here is actually a depletion of a resource, where
ENOBUFS is the more fitting error code.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling the variable l3edev was relevant when neighbor lookup was the
last stage in the simulated pipeline. Now that mlxsw handles bridges and
vlan devices as well, calling it "L3" is a misnomer.

Thus in mlxsw_sp_span_dmac(), rename to "dev", because that function is
just a service routine where the distinction between tunnel and egress
device isn't necessary.

In mlxsw_sp_span_entry_tunnel_parms_common(), rename to "edev" to
emphasize that the routine traces packet egress.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some reason, Willem thought that the issue we fixed for TCP
in commit 7ec318fe ("tcp: gso: avoid refcount_t warning from
tcp_gso_segment()") was not relevant for UDP GSO.

But syzbot found its way.

refcount_t: saturated; leaking memory.
WARNING: CPU: 0 PID: 10261 at lib/refcount.c:78 refcount_add_not_zero+0x2d4/0x320 lib/refcount.c:78
Kernel panic - not syncing: panic_on_warn set ...

CPU: 0 PID: 10261 Comm: syz-executor5 Not tainted 4.17.0-rc3+ #38
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1b9/0x294 lib/dump_stack.c:113
 panic+0x22f/0x4de kernel/panic.c:184
 __warn.cold.8+0x163/0x1b3 kernel/panic.c:536
 report_bug+0x252/0x2d0 lib/bug.c:186
 fixup_bug arch/x86/kernel/traps.c:178 [inline]
 do_error_trap+0x1de/0x490 arch/x86/kernel/traps.c:296
 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:315
 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992
RIP: 0010:refcount_add_not_zero+0x2d4/0x320 lib/refcount.c:78
RSP: 0018:ffff880196db6b90 EFLAGS: 00010282
RAX: 0000000000000026 RBX: 00000000ffffff01 RCX: ffffc900040d9000
RDX: 0000000000004a29 RSI: ffffffff8160f6f1 RDI: ffff880196db66f0
RBP: ffff880196db6c78 R08: ffff8801b33d6740 R09: 0000000000000002
R10: ffff8801b33d6740 R11: 0000000000000000 R12: 0000000000000000
R13: 00000000ffffffff R14: ffff880196db6c50 R15: 0000000000020101
 refcount_add+0x1b/0x70 lib/refcount.c:102
 __udp_gso_segment+0xaa5/0xee0 net/ipv4/udp_offload.c:272
 udp4_ufo_fragment+0x592/0x7a0 net/ipv4/udp_offload.c:301
 inet_gso_segment+0x639/0x12b0 net/ipv4/af_inet.c:1342
 skb_mac_gso_segment+0x3ad/0x720 net/core/dev.c:2792
 __skb_gso_segment+0x3bb/0x870 net/core/dev.c:2865
 skb_gso_segment include/linux/netdevice.h:4050 [inline]
 validate_xmit_skb+0x54d/0xd90 net/core/dev.c:3122
 __dev_queue_xmit+0xbf8/0x34c0 net/core/dev.c:3579
 dev_queue_xmit+0x17/0x20 net/core/dev.c:3620
 neigh_direct_output+0x15/0x20 net/core/neighbour.c:1401
 neigh_output include/net/neighbour.h:483 [inline]
 ip_finish_output2+0xa5f/0x1840 net/ipv4/ip_output.c:229
 ip_finish_output+0x828/0xf80 net/ipv4/ip_output.c:317
 NF_HOOK_COND include/linux/netfilter.h:277 [inline]
 ip_output+0x21b/0x850 net/ipv4/ip_output.c:405
 dst_output include/net/dst.h:444 [inline]
 ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124
 ip_send_skb+0x40/0xe0 net/ipv4/ip_output.c:1434
 udp_send_skb.isra.37+0x5eb/0x1000 net/ipv4/udp.c:825
 udp_push_pending_frames+0x5c/0xf0 net/ipv4/udp.c:853
 udp_v6_push_pending_frames+0x380/0x3e0 net/ipv6/udp.c:1105
 udp_lib_setsockopt+0x59a/0x600 net/ipv4/udp.c:2403
 udpv6_setsockopt+0x95/0xa0 net/ipv6/udp.c:1447
 sock_common_setsockopt+0x9a/0xe0 net/core/sock.c:3046
 __sys_setsockopt+0x1bd/0x390 net/socket.c:1903
 __do_sys_setsockopt net/socket.c:1914 [inline]
 __se_sys_setsockopt net/socket.c:1911 [inline]
 __x64_sys_setsockopt+0xbe/0x150 net/socket.c:1911
 do_syscall_64+0x1b1/0x800 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: ad405857 ("udp: better wmem accounting on gso")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Acked-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux-4.16 got support for softirq based hrtimers.
TCP can switch its pacing hrtimer to this variant, since this
avoids going through a tasklet and some atomic operations.

pacing timer logic looks like other (jiffies based) tcp timers.

v2: use hrtimer_try_to_cancel() in tcp_clear_xmit_timers()
    to correctly release reference on socket if needed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: Plug in PHYLINK support

This patch series adds PHYLINK support to DSA which is necessary to support more
complex PHY and pluggable modules setups.

Patch series can be found here:

https://github.com/ffainelli/linux/commits/dsa-phylink-v2

This was tested on:

- dsa-loop
- bcm_sf2
- mv88e6xxx
- b53

With a variety of test cases:
- internal & external MDIO PHYs
- MoCA with link notification through interrupt/MMIO register
- built-in PHYs
- ifconfig up/down for several cycles works
- bind/unbind of the drivers

Changes in v2:

- fixed link configuration for mv88e6xxx (Andrew) after introducing polling

This is technically v2 of what was posted back in March 2018, changes from last
time:

- fixed probe/remove of drivers
- fixed missing gpiod_put() for link GPIOs
- fixed polling of link GPIOs (Russell I would need your SoB on the patch you
  provided offline initially, added some modifications to it)
- tested across a wider set of platforms

And everything should still work as expected. Please be aware of the following:

- switch drivers (like bcm_sf2) which may have user-facing network ports using
  fixed links would need to implement phylink_mac_ops to remain functional.
  PHYLINK does not create a phy_device for fixed links, therefore our
  call to adjust_link() from phylink_mac_link_{up,down} would not be calling
  into the driver. This *should not* affect CPU/DSA ports which are configured
  through adjust_link() but have no network devices

- support for SFP/SFF is now possible, but switch drivers will still need some
  modifications to properly support those, including, but not limited to using
  the correct binding information. This will be submitted on top of this series

Please do test on your respective platforms/switches and let me know if you
find any issues, hopefully everything still works like before.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have converted the bcm_sf2 driver to implement PHYLINK MAC
operations, we can remove the PHYLIB callbacks: adjust_link() and
fixed_link_update() which are no longer called by DSA.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for PHYLINK within the DSA subsystem in order to support more
complex devices such as pluggable (SFP) and non-pluggable (SFF) modules, 10G
PHYs, and traditional PHYs. Using PHYLINK allows us to drop some amount of
complexity we had while probing fixed and non-fixed PHYs using Device Tree.

Because PHYLINK separates the Ethernet MAC/port configuration into different
stages, we let switch drivers implement those, and for now, we maintain
functionality by calling dsa_slave_adjust_link() during
phylink_mac_link_{up,down} which provides semantically equivalent steps.

Drivers willing to take advantage of PHYLINK should implement the phylink_mac_*
operations that DSA wraps.

We cannot quite remove the adjust_link() callback just yet, because a number of
drivers rely on that for configuring their "CPU" and "DSA" ports, this is done
dsa_port_setup_phy_of() and dsa_port_fixed_link_register_of() still.

Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2) will need
to implement phylink_mac_ops from now on to preserve functionality, since PHYLINK
*does not* create a phy_device instance for fixed links.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rudimentary phylink support to mv88e6xxx. This allows the driver
using user ports with fixed links to keep operating normally. User ports
with normal PHYs are not affected since the switch automatically manages
their link parameters. User facing ports which use a SFP/SFF with a
non-fixed link mode might require a call to phylink_mac_change() to
operate properly.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
[Andrew: fixed link setting after adding link polling]
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
[florian: expand commit message]
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we use PHYLIB to manage the per-port link indication, this will
also be reflected correctly in the network device's carrier state, so we
can use ethtool_op_get_link() instead.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the bcm_sf2 driver implement phylink_mac_ops since it needs to
support a wide variety of network interfaces: internal & external MDIO
PHYs, fixed PHYs, MoCA with MMIO link status.

A large amount of what needs to be done already exists under
bcm_sf2_sw_adjust_link() so we are essentially breaking this down into
the necessary operation for PHYLINK to work: mac_config, mac_link_up,
mac_link_down and validate. We can now entirely get rid of most of what
fixed_link_update() provided because only the link information is actually
necessary. We still have to force DUPLEX_FULL for legacy Device Tree bindings
that did not specify that before.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding support for PHYLINK within DSA, define a number of
operations that we will need and that switch drivers can start implementing.
Proper integration with PHYLINK will follow in subsequent patches.

We start selecting PHYLINK (which implies PHYLIB) in net/dsa/Kconfig
such that drivers can be guaranteed that this dependency is properly
taken care of and can start referencing PHYLINK helper functions without
requiring stubs or anything.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a fixed link with a link GPIO, we need to poll that GPIO to
determine link state changes. This is consistent with what fixed_phy.c does.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are not releasing the link GPIO descriptor with gpiod_put() which results in
subsequent probing to get -EBUSY when calling fwnode_get_named_gpiod(). Fix this
by doing the release in phylink_destroy().

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIO provider for the link GPIO line might require the use of the
_cansleep() API, utilize that. This is safe to do since we run in workqueue
context.

Fixes: 9525ae83 ("phylink: add phylink infrastructure")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Breaking out of the switch in rocker_switchdev_event() still ends up
scheduling work, except an ill-defined one. This leads to an OOPS cited
below. Fix by postponing the check until rocker_switchdev_event_work().

[   23.148476] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[   23.148810] PGD 0 P4D 0
[   23.148982] Oops: 0000 [#1] PREEMPT SMP PTI
[   23.149190] Modules linked in: bridge stp llc iptable_nat nf_nat_ipv4 nf_nat e1000 rocker
[   23.149768] CPU: 0 PID: 239 Comm: kworker/u2:4 Not tainted 4.17.0-rc3-net_next_queue-custom #6
[   23.150298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[   23.150868] Workqueue: rocker rocker_switchdev_event_work [rocker]
[   23.151258] RIP: 0010:ofdpa_port_fdb+0x7b/0x230 [rocker]
[   23.151597] RSP: 0018:ffffc900004b3e18 EFLAGS: 00010246
[   23.151952] RAX: 00000000fffbc68c RBX: 0000000000000000 RCX: 0000000000000000
[   23.152363] RDX: 0000000000000010 RSI: ffff88003b4471e0 RDI: 00000000ffffffff
[   23.152768] RBP: ffff88003b4471c0 R08: ffff88003b4471e0 R09: ffff88003b4471c0
[   23.153141] R10: 0000000000000000 R11: 0000000000000000 R12: ffff880036caf000
[   23.153515] R13: 0000000000000000 R14: 0000000000000000 R15: ffff88003bc00000
[   23.153919] FS:  0000000000000000(0000) GS:ffff88003fc00000(0000) knlGS:0000000000000000
[   23.154444] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   23.154806] CR2: 0000000000000000 CR3: 0000000036eb6000 CR4: 00000000000006f0
[   23.155194] Call Trace:
[   23.155472]  rocker_switchdev_event_work+0x9b/0xd0 [rocker]
[   23.155850]  ? __schedule+0x231/0x700
[   23.156175]  process_one_work+0x1cf/0x3e0
[   23.156490]  worker_thread+0x26/0x3d0
[   23.156795]  ? trace_event_raw_event_workqueue_execute_start+0x80/0x80
[   23.157181]  kthread+0x10e/0x130
[   23.157485]  ? kthread_create_worker_on_cpu+0x40/0x40
[   23.157824]  ret_from_fork+0x35/0x40
[   23.158174] Code: 00 00 c1 e8 02 4c 8d 45 20 bf ff ff ff ff 83 e0 01 4c 89 65 20 88 45 14 48 8b 05 21 da 1f e2 4c 89 c6 4c 89 44 24 10 48 89 45 18 <41> 8b 45 00 89 45 28 41 0f b7 45 04 66 89 45 2c 0f b7 44 24 04
[   23.159346] RIP: ofdpa_port_fdb+0x7b/0x230 [rocker] RSP: ffffc900004b3e18
[   23.159742] CR2: 0000000000000000
[   23.160088] ---[ end trace f9b16d4cb6df0629 ]---

Fixes: 816a3bed ("switchdev: Add fdb.added_by_user to switchdev notifications")
Suggested-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add sg table initialization to fix a BUG_ON encountered when enabling
CONFIG_DEBUG_SG.
Signed-off-by: NBoris Pismenny <borisp@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix the wrong conversion where 1 Mbps was converted to
1024 Kbps.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Support VLAN devices in mirroring offloads

Petr says:

When offloading "tc action mirred mirror", there are several scenarios
where VLAN devices can show up, that mlxsw can offload on Spectrum
machines.

I) A direct mirror to a VLAN device on top of a front-panel port device
   (commonly referred to as "RSPAN")

II) VLAN device in egress path of a packet when resolving a mirror to
    gretap or ip6gretap netdevice.

Specifically in the latter case, the following are the cases that can be
offloaded:

IIa) VLAN device directly above a physical device.
IIb) A VLAN-unaware bridge where the egress device is as in IIa.
IIc) VLAN device on top of a VLAN-aware bridge where the egress device
     is a physical device.

This patch set implements all the above cases.

First, in patch #1, br_vlan_get_info() is extended to allow bridge
master argument.

Case I is then implemented in patches #2 and #3, case II in patch #4.

Note that handling of VLAN protocol is not included. In case I, mirrored
packets may end up being double-tagged, and it might be reasonable for
the outer tag to be an 802.1ad. However, the protocol type configuration
would have to be put on the same VLAN netdevice that represents normal
VLAN traffic, and mlxsw currently ignores this setting in that case. Thus
this support was left out and the encapsulation always uses 802.1q
protocol.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mirroring to a gretap or ip6gretap device, allow the underlay
packet path to include VLAN devices. The following configurations are
supported in underlay:

- vlan over phys
- vlan-unaware bridge where the egress device is vlan over phys
- vlan over vlan-aware bridge where the egress device is phys
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload "tc action mirred mirror" to a device that is a vlan device on
top of a front-panel port device. The hardware encapsulates the mirrored
packets in a VLAN tag. That includes the case that the mirrored traffic
is already VLAN-tagged--in that case the monitor traffic will be
double-tagged, just like in the software path.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MLXSW_REG_MPAT_SPAN_TYPE_REMOTE_ETH to support VLAN-encapsulated
port mirroring.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mirroring offload in mlxsw needs to check that a given VLAN is allowed
to ingress the bridge device. br_vlan_get_info() is the function that is
used for this, however currently it only supports bridge port devices.
Extend it to support bridge masters as well.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This version has some suggestions by Eric Dumazet:

- Use a local variable for the mark in IPv6 instead of ctl_sk to avoid SMP
races.
- Use the more elegant "IP4_REPLY_MARK(net, skb->mark) ?: sk->sk_mark"
statement.
- Factorize code as sk_fullsock() check is not necessary.

Aidan McGurn from Openwave Mobility systems reported the following bug:

"Marked routing is broken on customer deployment. Its effects are large
increase in Uplink retransmissions caused by the client never receiving
the final ACK to their FINACK - this ACK misses the mark and routes out
of the incorrect route."

Currently marks are added to sk_buffs for replies when the "fwmark_reflect"
sysctl is enabled. But not for TW sockets that had sk->sk_mark set via
setsockopt(SO_MARK..).

Fix this in IPv4/v6 by adding tw->tw_mark for TIME_WAIT sockets. Copy the the
original sk->sk_mark in __inet_twsk_hashdance() to the new tw->tw_mark location.
Then progate this so that the skb gets sent with the correct mark. Do the same
for resets. Give the "fwmark_reflect" sysctl precedence over sk->sk_mark so that
netfilter rules are still honored.
Signed-off-by: NJon Maxwell <jmaxwell37@gmail.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

INET_CSK_DEBUG is always set and only is used for 2 pr_debug calls.

EXPORT_SYMBOL(inet_csk_timer_bug_msg) is only used by these 2
pr_debug calls and is also unnecessary as the exported string can
be used directly by these calls.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The liquidio_watchdog kernel thread is watching over only 12 cores of the
Octeon CN23XX; it's neglecting the other 4 cores that are present in the
CN2360.  Fix it by defining LIO_MAX_CORES as 16.
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2018-05-09

This series contains updates to fm10k only.

Jake provides all the changes in the series, starting with adding
support for accelerated MACVLAN devices.  Reduced code duplication by
implementing a macro to be used when setting up the type specific
macros.  Avoided potential bugs with stats by using a macro to calculate
the array size when passing to ensure that the size is correct.

v2: changed macro reference '#' with __stringify() as suggested by
    Joe Perches to patch 2 of the series.  Also made sure the updated
    series of patches is actually pushed to my kernel.org tree
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WARNING: lock held when returning to user space!
4.17.0-rc3+ #37 Not tainted

syz-executor1/27662 is leaving the kernel with locks still held!
1 lock held by syz-executor1/27662:
 #0: 00000000f661aee7 (rcu_read_lock){....}, at: ip6_route_del+0xea/0x13f0 net/ipv6/route.c:3206
BUG: scheduling while atomic: syz-executor1/27662/0x00000002
INFO: lockdep is turned off.
Modules linked in:
Kernel panic - not syncing: scheduling while atomic

CPU: 1 PID: 27662 Comm: syz-executor1 Not tainted 4.17.0-rc3+ #37
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1b9/0x294 lib/dump_stack.c:113
 panic+0x22f/0x4de kernel/panic.c:184
 __schedule_bug.cold.85+0xdf/0xdf kernel/sched/core.c:3290
 schedule_debug kernel/sched/core.c:3307 [inline]
 __schedule+0x139e/0x1e30 kernel/sched/core.c:3412
 schedule+0xef/0x430 kernel/sched/core.c:3549
 exit_to_usermode_loop+0x220/0x310 arch/x86/entry/common.c:152
 prepare_exit_to_usermode arch/x86/entry/common.c:196 [inline]
 syscall_return_slowpath arch/x86/entry/common.c:265 [inline]
 do_syscall_64+0x6ac/0x800 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x455979
RSP: 002b:00007fbf4051dc68 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: 0000000000000000 RBX: 00007fbf4051e6d4 RCX: 0000000000455979
RDX: 00000000200001c0 RSI: 000000000000890c RDI: 0000000000000013
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000003c8 R14: 00000000006f9b60 R15: 0000000000000000
Dumping ftrace buffer:
   (ftrace buffer empty)
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: 23fb93a4 ("net/ipv6: Cleanup exception and cache route handling")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@gmail.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Misc bug fixes for HNS3 Ethernet Driver

Fixes to some of the bugs found during system test, internal review
and clean-up
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors the loopback related function in order
to support the serdes loopback.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>