Support for sending multiple gratuitous ARPs during failovers
was added by commit:

commit 7893b249
Author: Moni Shoua <monis@voltaire.com>
Date:   Sat May 17 21:10:12 2008 -0700

    bonding: Send more than one gratuitous ARP when slave takes over

	This change modifies that support to remove duplicated code,
add support for ARP monitor (the original only supported miimon), clear
the grat ARP counter in bond_close (lest a later "ifconfig up" immediately
start spewing ARPs), and add documentation for the module parameter.

	Also updated driver version to 3.3.0.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

under active-backup mode and when there's actual new_active slave,
have bond_change_active_slave() call the networking core to deliver
NETDEV_BONDING_FAILOVER event such that the fail-over can be notable
by code outside of the bonding driver such as the RDMA stack and
monitoring tools.

As the correct context of locking appropriate for notifier calls is RTNL
and nothing else, bond->curr_slave_lock and bond->lock are unlocked and
later locked again. This is ensured by the rest of the code to be safe
under backup-mode AND when new_active is not NULL.

Jay Vosburgh modified the original patch for formatting and fixed a
compiler error.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

simplified the code of bond_change_active_slave() such that under
active-backup mode there's one "if (new_active)" test and the rest
of the code only does extra checks on top of it. This removed an
unneeded "if (bond->send_grat_arp > 0)" check and avoid calling
bond_send_gratuitous_arp when there's no active slave.

Jay Vosburgh made minor coding style changes to the orignal patch.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add NETDEV_BONDING_FAILOVER event to be used in a successive patch
by bonding to announce fail-over for the active-backup mode through the
netdev events notifier chain mechanism. Such an event can be of use for the
RDMA CM (communication manager) to let native RDMA ULPs (eg NFS-RDMA, iSER)
always be aligned with the IP stack, in the sense that they use the same
ports/links as the stack does. More usages can be done to allow monitoring
tools based on netlink events being aware to bonding fail-over.
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

New version to reflect new hardware support
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add support for Yukon 2 Ultra 2 chip set (88E8057) based on code in latest
version of vendor driver (sk98lin 10.60.2.3).  Untested on real hardware.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

PCI device table can be marked as devinitconst by using macro.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Change how chip version is printed so that if an unknown version is detected
nothing breaks.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Change the setup of the PHY registers on some chip ids. These changes
make the latest sky2 driver follow the vendor driver.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The arch/ppc sub-tree has been removed in the powerpc git tree.  The old
ibm_emac driver is no longer used by anything as a result of this.  This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ROSE network is organized through nodes connected via hamradio or Internet.
AX25 packet radio frames sent to a remote ROSE address destination are routed
through these nodes.

Without the present patch, automatic routing mechanism did not work optimally
due to an improper parameter checking.

rose_get_neigh() function is called either by rose_connect() or by
rose_route_frame().

In the case of a call from rose_connect(), f0 timer is checked to find if a connection
is already pending. In that case it returns the address of the neighbour, or returns a NULL otherwise.

When called by rose_route_frame() the purpose was to route a packet AX25 frame
through an adjacent node given a destination rose address.
However, in that case, t0 timer checked does not indicate if the adjacent node
is actually connected even if the timer is not null. Thus, for each frame sent, the
function often tried to start a new connexion even if the adjacent node was already connected.

The patch adds a "new" parameter that is true when the function is called by
rose route_frame().
This instructs rose_get_neigh() to check node parameter "restarted". 
If restarted is true it means that the route to the destination address is opened via a neighbour
node already connected.
If "restarted" is false the function returns a NULL.
In that case the calling function will initiate a new connection as before.

This results in a fast routing of frames, from nodes to nodes, until
destination is reached, as originaly specified by ROSE protocole.
Signed-off-by: NBernard Pidoux <f6bvp@amsat.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the most obvious 64-bit problems, but it is still very very
broken in other aspects.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Mitchell Blank Jr <mitch@sfgoth.com>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bridge netfilter code so that it uses CONFIG_IPV6 as needed:

net/built-in.o: In function `ebt_filter_ip6':
ebt_ip6.c:(.text+0x87c37): undefined reference to `ipv6_skip_exthdr'
net/built-in.o: In function `ebt_log_packet':
ebt_log.c:(.text+0x88dee): undefined reference to `ipv6_skip_exthdr'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Normally, the bridge just chooses the smallest mac address as the
bridge id and mac address of bridge device. But if the administrator
has explictly set the interface address then don't change it.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Any frame addressed to link-local addresses should be processed by local
receive path. The earlier code would process them only if STP was enabled.
Since there are other frames like LACP for bonding, we should always
process them.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the sctp_remaddr_proc_init failed, the proper rollback is
not the sctp_remaddr_proc_exit, but the sctp_assocs_proc_exit.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In nr_release(), one code path calls sock_orphan() which
will NULL out sk->sk_socket already.

In the other case, handling states other than NR_STATE_{0,1,2,3},
seems to not be possible other than due to bugs.  Even for an
uninitialized nr->state value, that would be zero or NR_STATE_0.
It might be wise to stick a WARN_ON() here.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't grab the sk_callback_lock, it doesn't NULL out
the sk->sk_sleep waitqueue pointer, etc.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It doesn't grab the sk_callback_lock, it doesn't NULL out
the sk->sk_sleep waitqueue pointer, etc.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the x25 variant of changeset
9375cb8a
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the rose variant of changeset
9375cb8a
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the netrom variant of changeset
9375cb8a
("ax25: Use sock_graft() and remove bogus sk_socket and sk_sleep init.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The way that listening sockets work in ax25 is that the packet input
code path creates new socks via ax25_make_new() and attaches them
to the incoming SKB.  This SKB gets queued up into the listening
socket's receive queue.

When accept()'d the sock gets hooked up to the real parent socket.
Alternatively, if the listening socket is closed and released, any
unborn socks stuff up in the receive queue get released.

So during this time period these sockets are unreachable in any
other way, so no wakeup events nor references to their ->sk_socket
and ->sk_sleep members can occur.  And even if they do, all such
paths have to make NULL checks.

So do not deceptively initialize them in ax25_make_new() to the
values in the listening socket.  Leave them at NULL.

Finally, use sock_graft() in ax25_accept().
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just expand the wait sequence.  And as a nice side-effect
the timeout is respected now.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:

	drivers/net/wireless/rt2x00/Kconfig
	drivers/net/wireless/rt2x00/rt2x00usb.c
	net/sctp/protocol.c

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: "Robert T. Johnson" <rtjohnso@eecs.berkeley.edu>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>

From: Eric Kinzie <ekinzie@cmf.nrl.navy.mil>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This causes the suni driver to oops if you try to use sonetdiag to get
the statistics. Also add the corresponding phy->stop call to fix another
oops if you try to remove the module.
Signed-off-by: NJorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>