The intent of the warning is to warn if the ADMA table
overflows.  However there can be one more 'end' entry
so the condition should be adjusted accordingly.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Bytes are being copied from/to a single page.  The intent
of the warning is to warn if the page boundary is crossed.
There are two problems.  First, PAGE_MASK is mistaken for
(PAGE_SIZE - 1).  Secondly, instead of using the number
of bytes to copy, the warning is using the maximum that
that value could be.  Fix both.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ADMA2 descriptor table size was being calculated incorrectly
Fix it.

Note that it has been wrong for a long time and likely has not
caused any problems because of a combination of 1) not needing
alignment descriptors for block operations 2) more memory being
allocated than was requested 3) the use of
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC which does not use an extra
descriptor for the end marker.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add support for non-removable slots which have no card detection GPIO
and which should not be polled for a card change.
Signed-off-by: NTimo Kokkonen <timo.kokkonen@offcode.fi>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Besides the I/O clock, some PXAv3 SDHCI IP also requires a core clock to
be enabled. Add an optional core clock to the corresponding driver.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

With support for more than one clock, we'll need to distinguish between
the clock by name. Change clock probing to first try to get "io" clock
before falling back to unnamed clock.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As we are using references to the I/O clock throughout the driver,
move it to the private data. Also, in preparation for core clock,
rename it to clk_io.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sdhci_add_host and sdhci_platfm_init already report failure,
so don't emit error messages when a failure occurs. This prevents
occurences of "deferred" messages when required power supplies
are not ready for operation yet.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted.  However, this code was old and crufty and
should be removed.  Some evidence that it's really not needed:

1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
   using the built-in card detect mechanism.  The 'cd-gpio' code
   doesn't run any of the crufty old code but yet still works.

2. While looking at this, I realized that my old change (369ac861 mmc:
   dw_mmc: don't queue up a card detect at slot startup) actually
   castrated the old code a little bit already and nobody noticed.
   Specifically "last_detect_state" was left as 0 at bootup.  That
   means that on the first card removal none of the crufty code ran.

3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
   while ejecting and inserting an SD Card and the world doesn't
   explode.

If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".

Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup.  That
was actually causing a real bug.  The card detect workqueue was
running while the system was trying to enumerate the card.  The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration.  The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: Nalim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

"ret" is a signed int, so use "%d" in format strings instead of "%u".
This prevents cryptic codes in error messages like this:
sdhci-arasan e0101000.sdhci: platform register failed (4294966779)
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the mach header that can come either from arm/mach-at91 or avr32 to
platform_data to be able to switch the AT91 platforms to multiplatform.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]

The "set_ios" function is called with a clock of 0 when the clock is
turning off.  There's no reason to go through all the extra Rockchip
logic (whose goal is to make sure DIV is 0 or 1) in that case.  The
Rockchip logic happened to work because the CCF will pick the lowest
possible rate when you ask it for a clock of 0, but it's silly to go
through all the remuxing and adjusting for no reason.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages.  Don't print an ugly error in the logs when that happens.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We've already got a reset of DMA after it's done.  Add one before we
start DMA too.  This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.

We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: NSonny Rao <sonnyrao@chromium.org>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The msm_sdcc host shall not use mmc core specific macros to handle its
driver data. Instead, convert to use the platform device driver macros.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

NULL-checking a struct clk it not only wrong but also not required as
for PXAv3 driver the corresponding clock is mandatory. Remove the
checks from sdhci_pxav3_runtime_{suspend,resume}.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

clk_enable from struct sdhci_pxa is unused, remove it from the private
driver data.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

struct sdhci_pxa is only used in sdhci_pxa driver itself, so move it
there.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

commit bb8175a8
  ("mmc: sdhci: clarify DDR timing mode between SD-UHS and eMMC")
added MMC_DDR52 as eMMC's DDR mode to be distinguished from SD-UHS.

While the differentation may be useful, pxav3 SDHCI controller lacks
a corresponding check in its custom .set_uhs_signaling callback for
MMC_DDR52. This patch adds a new switch case for MMC_TIMING_MMC_DDR52
to MMC_TIMING_UHS_DDR50 case.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

struct sdhci_pxa is private data of PXA SDHCI driver, but not used in
sdhci-pxav2 at all. Drop unused references to struct sdhci_pxa.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the post request is cancelling the channel and descriptor and which are
equal to host->dma_current and host->dma_desc_current respectively, then it
makes sense to reset these pointers to NULL, so that the driver does not
reference it.

Also the host_cookie can be reset to 0 in cases of error, so that the
core could reissue the same mmc_request.

This patch was tested with 'mmc: core: fix prepared requests while doing
bkops' to fix the below issue.

mmci-pl18x 12400000.sdcc: error during DMA transfer!
Unable to handle kernel paging request at virtual address 40000000
pgd = c0204000
[40000000] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: ipv6 ath6kl_sdio ath6kl_core
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W      3.17.0-rc7-linaro-multi-v7 #1
task: c0c9d7e0 ti: c0c92000 task.ti: c0c92000
PC is at v7_dma_inv_range+0x34/0x4c
LR is at __dma_page_dev_to_cpu+0x80/0x100
pc : [<c021efc0>]    lr : [<c021af18>]    psr: 400f0193
sp : c0c93e20  ip : c0c9a478  fp : c08ea538
r10: c0c9f548  r9 : 00000002  r8 : e97d9000
r7 : 00000200  r6 : c0c9d504  r5 : c0db0880  r4 : 00000000
r3 : 0000003f  r2 : 00000040  r1 : 40000200  r0 : 40000000
Flags: nZcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5787d  Table: a9ef406a  DAC: 00000015
Process swapper/0 (pid: 0, stack limit = 0xc0c92250)
Stack: (0xc0c93e20 to 0xc0c94000)
3e20: c021f058 e9a17178 e9a171bc e99dfd6c 00000001 00000001 e995de10 00000002
3e40: 00000000 c021b574 00000000 c04bc4a4 00000000 e9b49ac0 c0ce6e6c e99dfda4
3e60: 00000088 e9810780 c0d8291c c072ea58 00000000 c072d3fc 00000000 c072f534
3e80: 00000000 e9b49ac0 00000100 c0c9a444 00000088 c072f6b4 c072f5d4 e9d40080
3ea0: e98107dc 00000000 00000000 c0280a60 00000000 7d55bf61 e9810780 e98107dc
3ec0: 00000000 f0002000 c0d460e8 c0d460e8 c0c92000 c0280b60 e9810780 c0ce7190
3ee0: 00000000 c028369c c02835f4 00000088 00000088 c0280278 c0c8ec70 c020f080
3f00: f000200c c0c9a958 c0c93f28 c02088e4 c04bd630 c04bd5bc 200f0013 ffffffff
3f20: c0c93f5c c0212800 00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff c04bd574 c071bd24 7d50c9b4 c0719a44
3f80: 7d50c9b4 0000015b c0c9a498 c0c92028 c0c9a498 c0c9a4fc ea7a0e40 c0c8ee38
3fa0: c0d460e8 c0276198 00000000 c0d8291a 00000000 c0c9a400 00000000 c0be0bc4
3fc0: ffffffff ffffffff c0be05f8 00000000 00000000 c0c533d8 c0d82ed4 c0c9a47c
3fe0: c0c533d4 c0c9e870 8020406a 511f06f0 00000000 80208074 00000000 00000000
[<c021efc0>] (v7_dma_inv_range) from [<c021af18>] (__dma_page_dev_to_cpu+0x80/0x100)
[<c021af18>] (__dma_page_dev_to_cpu) from [<c021b574>] (arm_dma_unmap_sg+0x5c/0x84)
[<c021b574>] (arm_dma_unmap_sg) from [<c072ea58>] (mmci_dma_unmap.isra.16+0x60/0x74)
[<c072ea58>] (mmci_dma_unmap.isra.16) from [<c072f534>] (mmci_data_irq+0x1fc/0x29c)
[<c072f534>] (mmci_data_irq) from [<c072f6b4>] (mmci_irq+0xe0/0x114)
[<c072f6b4>] (mmci_irq) from [<c0280a60>] (handle_irq_event_percpu+0x78/0x134)
[<c0280a60>] (handle_irq_event_percpu) from [<c0280b60>] (handle_irq_event+0x44/0x64)
[<c0280b60>] (handle_irq_event) from [<c028369c>] (handle_fasteoi_irq+0xa8/0x1a8)
[<c028369c>] (handle_fasteoi_irq) from [<c0280278>] (generic_handle_irq+0x2c/0x3c)
[<c0280278>] (generic_handle_irq) from [<c020f080>] (handle_IRQ+0x40/0x90)
[<c020f080>] (handle_IRQ) from [<c02088e4>] (gic_handle_irq+0x38/0x68)
[<c02088e4>] (gic_handle_irq) from [<c0212800>] (__irq_svc+0x40/0x54)
Exception stack(0xc0c93f28 to 0xc0c93f70)
3f20:                   00000001 a987c000 c0c93f3c c04bd574 00000000 0000015b
3f40: ea7a0e40 00000000 c0d460e8 c0d460e8 c0c92000 c08ea538 29b12000 c0c93f70
3f60: c04bd630 c04bd5bc 200f0013 ffffffff
[<c0212800>] (__irq_svc) from [<c04bd5bc>] (msm_cpu_pm_enter_sleep+0x48/0x4c)
[<c04bd5bc>] (msm_cpu_pm_enter_sleep) from [<c071bd24>] (qcom_lpm_enter_spc+0x20/0x2c)
[<c071bd24>] (qcom_lpm_enter_spc) from [<c0719a44>] (cpuidle_enter_state+0x44/0xf0)
[<c0719a44>] (cpuidle_enter_state) from [<c0276198>] (cpu_startup_entry+0x1f4/0x238)
[<c0276198>] (cpu_startup_entry) from [<c0be0bc4>] (start_kernel+0x384/0x390)
Code: 1e070f3e e1110003 e1c11003 1e071f3e (ee070f36)
---[ end trace cf6cb3f6432c9834 ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the case of SET_BLOCK_COUNT command error to the error conditions
check for making a controller reset at request handling finish.
Otherwise, if the SET_BLOCK_COUNT command failed, e.g. with a timeout,
the controller state was not reset, and the next command failed too.

In the case of data error the controller reset is already done in
finish_data() function before sending stop command (if present),
so the finish tasklet should make a reset after data error only
if no stop command existed in the request.

Also, fix the indentation of this condition check to make it more logical.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As a follow-up of commit
"mmc: sdhci: Balance vmmc regulator_enable(), and always enable vqmmc"
vmmc regulator disable is also not needed in sdhci_remove_host.
The regulator is completely controlled by mmc_power_up and mmc_power_off
functions and is already disabled by the time of removing the host.
Extra regulator_disable call in sdhci_remove_host is unbalanced and
causes a warning reported by regulator core, so should be removed.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The commit ad93220d ("mmc: sdhci-esdhc-imx: change pinctrl state
according to uhs mode") exits the probe in case there are no valid
pinctrl states found.

As there are configurations doing the pin mux properly in the boot
loader, don't exit. Just warn, but go on in case if there are no
pinctrl states in the device tree.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If available voltages are not given, mmc_regulator_get_supply() function
returns 0 and mxcmmc driver doesn't set a value for ocr_avail mask.

In accordance with the comment in platform_data/mmc-mxcmmc.h,
fix it, assuming MMC_VDD_32_33 | MMC_VDD_33_34 as default value.
Signed-off-by: NMatteo Facchinetti <matteo.facchinetti@sirius-es.it>
Reviewed-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

During a read of data block using dma, driver might have two ways to finish to read
and free the resources:
1) checking STATUS_DATA_TRANS_DONE mask, in the mxcmci_irq() routine
   (pending to mmc irq)
2) mxmmc driver, registers also a mxcmci_dma_callback() and when transfer is finished,
   dma driver calls this callback. (pending to dma irq)
Both ways are concurrent with each other.

Race condition happens when following events occur:
/* (1) mxcmci driver start data transfer */
         158.418970: mpc_dma_execute: mpc_dma_execute(): will_access_peripheral start cid=31
         158.418976: mpc_dma_issue_pending <-mxcmci_request
         158.418983: mxcmci_start_cmd <-mxcmci_request
/* (2) mxcmci driver receive mmc irq */
         158.419656: mxcmci_irq <-handle_irq_event_percpu
         158.419692: mxcmci_read_response <-mxcmci_irq
/* (3) mxcmci driver checks that transfer is complete and call mxcmci_finish_data() */
         158.419726: mxcmci_data_done <-mxcmci_irq
         158.419729: mxcmci_finish_data <-mxcmci_data_done
         158.419733: dma_direct_unmap_sg <-mxcmci_finish_data
         158.419736: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
         158.419762: mxcmci_read_response <-mxcmci_data_done
/* (4) mxcmci driver (no dma): send stop command */
         158.419765: mxcmci_start_cmd <-mxcmci_data_done
/* (5) mxcmci driver (no dma): receive the stop command irq response */
         158.419782: mxcmci_irq <-handle_irq_event_percpu
         158.419812: mxcmci_read_response <-mxcmci_irq
         158.419843: mxcmci_finish_request <-mxcmci_irq
/* (6) dma driver: receive dma irq (finish data transfer) related by request on step 1 */
         158.419853: mpc_dma_irq <-handle_irq_event_percpu
         158.420001: mpc_dma_irq_process <-mpc_dma_irq
         158.420004: mpc_dma_irq_process <-mpc_dma_irq
/* (7) dma driver: start dma tasklet to finish the dma irq handling */
         158.420008: mpc_dma_irq_process: mpc_dma_irq_process(): completed ch:31
/* (8) mxcmci driver: start next data transfer using dma */
         158.420174: mxcmci_request <-mmc_start_req
         158.420182: dma_direct_map_sg <-mxcmci_request
         158.420192: mpc_dma_prep_slave_sg <-mxcmci_request
/* (9) dma driver: schedule irq tasklet and execute mxcmci dma driver callback */
         158.420250: mpc_dma_tasklet <-tasklet_action
         158.420254: mpc_dma_process_completed <-tasklet_action
         158.420267: mxcmci_dma_callback <-mpc_dma_process_completed
/* ERROR!!! (10) mxcmci driver callback works on dma data related to the step 1
                 that is already finished */
         158.420271: mxcmci_data_done <-mpc_dma_process_completed
         158.420273: mxcmci_finish_data <-mxcmci_data_done
/* ERROR!!! (11) mxcmci driver: clear data that should be used by step 8 and
                 send an other mmc stop command (already sended on step 4) */
         158.420276: dma_direct_unmap_sg <-mxcmci_finish_data
         158.420279: mxcmci_swap_buffers.isra.24 <-mxcmci_finish_data
         158.420330: mxcmci_read_response <-mxcmci_data_done
         158.420333: mxcmci_start_cmd <-mxcmci_data_done
         158.420338: dma_run_dependencies <-mpc_dma_process_completed
...
...
...
         168.474223: mxcmci_watchdog <-call_timer_fn
         168.474236: mxcmci_watchdog: mxcmci_watchdog
         168.474397: mpc_dma_device_control <-mxcmci_watchdog

In accordance with the other drivers that using the dma engine,
fix it, leaving *only* to dma driver the complete control to
ending the read operation.

Removing STATUS_READ_OP_DONE event activation, has as effect
to force mxcmci driver to handle the finish data transfer only
by mxcmci dma callback.
Signed-off-by: NMatteo Facchinetti <matteo.facchinetti@sirius-es.it>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Fix Dell E5440 when reboot Linux, can't find o2micro sd host chip issue.

Fixes: 01acf691 (mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts)
Signed-off-by: NPeter Guo <peter.guo@bayhubtech.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.  A similar fix was done
for sdhci-pci, however in the sdhci-acpi case the
HID/UID is not unique so the capabilities register
values are matched also.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Pass HID and UID to probe_slot so extra setup
can be done for specific ids.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

UID was made available on acpi_device since
commit ccf78040 ("ACPI: Add _UID support for ACPI devices.")
Use it from there instead of reprocessing the
ACPI object info.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.

Instead merely make them const and put the const in the right spot.
Signed-off-by: NBehan Webster <behanw@converseincode.com>
Reviewed-by: NMark Charlebois <charlebm@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NMatt Porter <mporter@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Braswell eMMC host controller specifies an incorrect
timeout clock frequncy in the capabilities registers.
The correct value is 1 MHz.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let a driver override the timeout clock frequency by
populating it before calling sdhci_add_host().  Note
the value will otherwise be zero because sdhci_host is
zeroed when allocated.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add support for card detect for Bay Trail
and Braswell SD Card host controllers in PCI
mode.

This uses the gpio descriptor API which can find
gpio descriptors, for example, on an ACPI comapnion
device.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add quirk SDHCI_QUIRK2_STOP_WITH_TC for Intel BYT host controllers.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a HID (INT33BB) and UID (3) for a SD Card host controller.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add quirk SDHCI_QUIRK2_STOP_WITH_TC for Intel host controllers.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

commit 98e90de9
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.

It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: NJavier Martinez Canillas <javier@dowhile0.org>
Tested-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>