This patch cleans devlink resources by calling devlink_port_unregister()
to avoid the following issues:

- Kernel panic when triggering reset flow.
- Memory leak due to unfreed resources in mlx4_init_port_info().

Fixes: 09d4d087 ("mlx4: Implement devlink interface")
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Disable ALDPS and EEE to avoid the possible failure when setting the PHY.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove r8153_enable_eee().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the PHY relative settings together to hw_phy_cfg().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move enabling PHY to init(), otherwise some other settings may fail.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the following functions forward.

	r8152_mmd_indirect()
	r8152_mmd_read()
	r8152_mmd_write()
	r8152_eee_en()
	r8152b_enable_eee()
	r8153_eee_en()
	r8153_enable_eee()
	r8152b_enable_fc()
	r8153_aldps_en()
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We were missing check for 25G and 100G while checking port speed,
which lead to less number of queues getting allocated for 25G & 100G
adapters and leading to low throughput. Adding the missing check for
both NIC and vNIC driver.

Also fixes port advertisement for 25G and 100G in ethtool output.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit fe56b9e6 ("qed: Add module with basic common support")
has introduced a stack corruption during probe, where filling a
local struct with data to be sent to management firmware is incorrectly
filled; The data is written outside of the struct and corrupts
the stack.

Changes from v1:
----------------
 - Correct the value written [Caught by David Laight]

Fixes: fe56b9e6 ("qed: Add module with basic common support")
Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

E-switch mode changes involve creating HW tables, potentially allocating
netdevices, etc, and things can fail. Add an attempt to rollback to the
existing mode when changing to the new mode fails. Only if rollback fails,
getting proper SRIOV functionality requires module unload or sriov
disablement/enablement.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enablement of the SRIOV e-switch in certain mode (switchdev or legacy)
fails, we must set the mode to none. Otherwise, we'll run into double free
based crashes when further attempting to deal with the e-switch (such
as when disabling sriov or unloading the driver).
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FW command output length should be only the length of struct
mlx5_cmd_fc_bulk out field. Failing to do so will cause the memcpy
call which is invoked later in the driver to write over wrong memory
address and corrupt kernel memory which results in random crashes.

This bug was found using the kernel address sanitizer (kasan).

Fixes: a351a1b0 ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Alexey Khoroshilov (https://lkml.org/lkml/2016/9/9/737):
riocm_send_close() is called from rio_cm_shutdown() under
spin_lock_bh(idr_lock), but riocm_send_close() uses a GFP_KERNEL
allocation.

Fix by taking riocm_send_close() outside of spinlock protected code.

[akpm@linux-foundation.org: remove unneeded `if (!list_empty())']
Link: http://lkml.kernel.org/r/20160915175402.10122-1-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Reported-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a regression caused by commit 2bc46b3a ("[media] media/pci:
convert drivers to use the new vb2_queue dev field").

Three places where q->dev should be set were missed, causing
a WARN.

Fixes: 2bc46b3a ("[media] media/pci: convert drivers to use the new vb2_queue dev field").
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NMarton Balint <cus@passwd.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

On a imx6ul-pico board the following error is seen during system suspend:

dpm_run_callback(): platform_pm_resume+0x0/0x54 returns -110
PM: Device 2090000.flexcan failed to resume: error -110

The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.

In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.

Based on a patch from Dong Aisheng in the NXP kernel.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Similar to struct drm_update_draw, struct drm_mode_fb_cmd2 has an
unaligned 64 bit field (modifier). This get packed differently between
32 bit and 64 bit modes on architectures that can handle unaligned 64
bit access (X86 and IA64).  Other architectures pack the structs the
same and don't need the compat wrapper. Use the same condition for
drm_mode_fb_cmd2 as we use for drm_update_draw.

Note that only the modifier will be packed differently between compat
and non-compat versions.
Reviewed-by: NRob Clark <robdclark@gmail.com>
Signed-off-by: NKristian H. Kristensen <hoegsberg@chromium.org>
[seanpaul added not at bottom of commit msg re: modifier]
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473801645-116011-1-git-send-email-hoegsberg@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

MAC devices use the RWKPKTEN and MGKPKTEN bits of the PMT Control/Status
register to generate power management events.
So this patch is to properly set the RWKPKTEN [BIT(2)] inside the
PMT register (needed in case of global unicast).
Reported-by: NAditi SHARMA <aditi-hed.sharma@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When CONFIG_PM is not set, we get a warning about an unused function:

drivers/gpu/drm/exynos/exynos_drm_gsc.c:1219:12: error: 'gsc_clk_ctrl' defined but not used [-Werror=unused-function]
 static int gsc_clk_ctrl(struct gsc_context *ctx, bool enable)
            ^~~~~~~~~~~~

This removes the two #ifdef checks in this file and instead marks the
functions as __maybe_unused, which is a more reliable way of doing the
same, allowing better build coverage and avoiding the warning above.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Move code from system sleep pm to runtime pm callbacks to ensure proper
driver state preservation when device is under power domain. Then, use
generic helpers for using runtime pm for system sleep pm.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Use generic helpers instead of open-coding usage of runtime pm for system
sleep pm, which was potentially broken for some corner cases.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Fix unsupported GEM memory type error message to include the memory type
information.
Signed-off-by: NShuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Commit 6e7333d3 "net: add rx_nohandler stat counter" added the new entry
rx_nohandler into struct rtnl_link_stats64. Unfortunately the bna
driver foolishly depends on the structure. It uses part of it for
ethtool statistics and it's not bad but the driver assumes its size
is constant as it defines string for each existing entry. The problem
occurs when the structure is extended because you need to modify bna
driver as well. If not any attempt to retrieve ethtool statistics results
in crash in bnad_get_strings().
The patch changes BNAD_ETHTOOL_STATS_NUM so it counts real number of
strings in the array and also removes rtnl_link_stats64 entries that
are not used in output and are always zero.

Fixes: 6e7333d3 "net: add rx_nohandler stat counter"
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ba5ca784 "bna: check for dma mapping errors" added besides other
things a statistic that counts number of DMA buffer mapping failures
per each Rx queue. This counter is not included in ethtool stats output.

Fixes: ba5ca784 "bna: check for dma mapping errors"
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error during netback_probe() (e.g. an entry missing on the
xenstore) netback_remove() is called on the new device, which will set
the device backend state to XenbusStateClosed by calling
set_backend_state(). However, the backend state wasn't initialized by
netback_probe() at this point, which will cause and invalid transaction
and set_backend_state() to BUG().

Initialize the backend state at the beginning of netback_probe() to
XenbusStateInitialising, and create two new valid state transitions on
set_backend_state(), from XenbusStateInitialising to XenbusStateClosed,
and from XenbusStateInitialising to XenbusStateInitWait.
Signed-off-by: NFilipe Manco <filipe.manco@neclab.eu>
Acked-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The userspace memory region 'mr' is allocated with kzalloc in
__rvt_alloc_mr  however it is incorrectly being freed with vfree in
__rvt_free_mr. Fix this by using kfree to free it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NDennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Decrement qp reference when handling error path
in completer to prevent kmem_cache leak.

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: NYonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

rxe_requester() is sending a pkt with rxe_xmit_packet() and
then calls rxe_update() to update the wqe and qp's psn values.
But sometimes the response is received before the requester
had time to update the wqe in which case the completer
acts on errornous wqe values.
This fix updates the wqe and qp before actually sending
the request and rolls back when xmit fails.

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: NYonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When handling ack for atomic opcodes like "fetch&add"
or "cmp&swp", the method send_atomic_ack() saves the ack
before sending it, in case it gets lost and never reach the
requester. In which case the method duplicate_request()
will need to find it using the duplicated request.psn.
But send_atomic_ack() used a wrong psn value and thus
the above ack was never found.
This fix uses the ack.psn to locate the ack in case
its needed.
This fix also copies the ack packet to the skb's control buffer
since duplicate_request() will need it when calling rxe_xmit_packet()

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: NYonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Disable creation of a UDP socket for ipv6 when
CONFIG_IPV6 is not enabeld. Since udp_sock_create6()
returns 0 when CONFIG_IPV6 is not set

[   46.888632] IP: [<c220705a>] setup_udp_tunnel_sock+0x6/0x4f
[   46.891355] *pdpt = 0000000000000000 *pde = f000ff53f000ff53
[   46.893918] Oops: 0002 [#1] PREEMPT
[   46.896014] CPU: 0 PID: 1 Comm: swapper Not tainted 4.7.0-rc4-00001-g8700e3e7 #1
[   46.900280] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[   46.904905] task: cf06c040 ti: cf05e000 task.ti: cf05e000
[   46.907854] EIP: 0060:[<c220705a>] EFLAGS: 00210246 CPU: 0
[   46.911137] EIP is at setup_udp_tunnel_sock+0x6/0x4f
[   46.914070] EAX: 00000044 EBX: 00000001 ECX: cf05fef0 EDX: ca8142e0
[   46.917236] ESI: c2c4505b EDI: cf05fef0 EBP: cf05fed0 ESP: cf05fed0
[   46.919836]  DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[   46.922046] CR0: 80050033 CR2: 000001fc CR3: 02cec000 CR4: 000006b0
[   46.924550] Stack:
[   46.926014]  cf05ff10 c1fd4657 ca8142e0 0000000a 00000000 00000000 0000b712 00000008
[   46.931274]  00000000 6bb5bd01 c1fd48de 00000000 00000000 cf05ff1c 00000000 00000000
[   46.936122]  cf05ff1c c1fd4bdf 00000000 cf05ff28 c2c4507b ffffffff cf05ff88 c2bf1c74
[   46.942350] Call Trace:
[   46.944403]  [<c1fd4657>] rxe_setup_udp_tunnel+0x8f/0x99
[   46.947689]  [<c1fd48de>] ? net_to_rxe+0x4e/0x4e
[   46.950567]  [<c1fd4bdf>] rxe_net_init+0xe/0xa4
[   46.953147]  [<c2c4507b>] rxe_module_init+0x20/0x4c
[   46.955448]  [<c2bf1c74>] do_one_initcall+0x89/0x113
[   46.957797]  [<c2bf15eb>] ? set_debug_rodata+0xf/0xf
[   46.959966]  [<c2bf1dbc>] ? kernel_init_freeable+0xbe/0x15b
[   46.962262]  [<c2bf1ddc>] kernel_init_freeable+0xde/0x15b
[   46.964418]  [<c232eb54>] kernel_init+0x8/0xd0
[   46.966618]  [<c2333122>] ret_from_kernel_thread+0xe/0x24
[   46.969592]  [<c232eb4c>] ? rest_init+0x6f/0x6f

Fixes: 8700e3e7 ("Soft RoCE driver")
Signed-off-by: NYonatan Cohen <yonatanc@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Set the source mac address in the FTE when L2 specification
is provided.

Fixes: 038d2ef8 ('IB/mlx5: Add flow steering support')
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.

Fixes: d603c809 ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: NDavid Chang <dchang@suse.com>
Signed-off-by: NNoa Osherovich <noaos@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Modify the mlx4_ib_diag_counters() to avoid the following error in the
hypervisor when the slave tries to query the hardware counters in SR-IOV
mode.

mlx4_core 0000:81:00.0: Unknown command:0x30 accepted from slave:1

Fixes: 3f85f2aa ("IB/mlx4: Add diagnostic hardware counters")
Signed-off-by: NKamal Heib <kamalh@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.

For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes.  Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.

However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.

Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.

Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.

Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.

Fixes: 1ffeb2eb ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.

This fix separates scope bits and join states bits a nibble each.

Fixes: b9c5d6a6 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

This fix solves a race between light flush and on the fly joins.
Light flush doesn't set the device to down and unset IPOIB_OPER_UP
flag, this means that if while flushing we have a MC join in progress
and the QP was attached to BC MGID we can have a mismatches when
re-attaching a QP to the BC MGID.

The light flush would set the broadcast group to NULL causing an on
the fly join to rejoin and reattach to the BC MCG as well as adding
the BC MGID to the multicast list. The flush process would later on
remove the BC MGID and detach it from the QP. On the next flush
the BC MGID is present in the multicast list but not found when trying
to detach it because of the previous double attach and single detach.

[18332.714265] ------------[ cut here ]------------
[18332.717775] WARNING: CPU: 6 PID: 3767 at drivers/infiniband/core/verbs.c:280 ib_dealloc_pd+0xff/0x120 [ib_core]
...
[18332.775198] Hardware name: Red Hat KVM, BIOS Bochs 01/01/2011
[18332.779411]  0000000000000000 ffff8800b50dfbb0 ffffffff813fed47 0000000000000000
[18332.784960]  0000000000000000 ffff8800b50dfbf0 ffffffff8109add1 0000011832f58300
[18332.790547]  ffff880226a596c0 ffff880032482000 ffff880032482830 ffff880226a59280
[18332.796199] Call Trace:
[18332.798015]  [<ffffffff813fed47>] dump_stack+0x63/0x8c
[18332.801831]  [<ffffffff8109add1>] __warn+0xd1/0xf0
[18332.805403]  [<ffffffff8109aebd>] warn_slowpath_null+0x1d/0x20
[18332.809706]  [<ffffffffa025d90f>] ib_dealloc_pd+0xff/0x120 [ib_core]
[18332.814384]  [<ffffffffa04f3d7c>] ipoib_transport_dev_cleanup+0xfc/0x1d0 [ib_ipoib]
[18332.820031]  [<ffffffffa04ed648>] ipoib_ib_dev_cleanup+0x98/0x110 [ib_ipoib]
[18332.825220]  [<ffffffffa04e62c8>] ipoib_dev_cleanup+0x2d8/0x550 [ib_ipoib]
[18332.830290]  [<ffffffffa04e656f>] ipoib_uninit+0x2f/0x40 [ib_ipoib]
[18332.834911]  [<ffffffff81772a8a>] rollback_registered_many+0x1aa/0x2c0
[18332.839741]  [<ffffffff81772bd1>] rollback_registered+0x31/0x40
[18332.844091]  [<ffffffff81773b18>] unregister_netdevice_queue+0x48/0x80
[18332.848880]  [<ffffffffa04f489b>] ipoib_vlan_delete+0x1fb/0x290 [ib_ipoib]
[18332.853848]  [<ffffffffa04df1cd>] delete_child+0x7d/0xf0 [ib_ipoib]
[18332.858474]  [<ffffffff81520c08>] dev_attr_store+0x18/0x30
[18332.862510]  [<ffffffff8127fe4a>] sysfs_kf_write+0x3a/0x50
[18332.866349]  [<ffffffff8127f4e0>] kernfs_fop_write+0x120/0x170
[18332.870471]  [<ffffffff81207198>] __vfs_write+0x28/0xe0
[18332.874152]  [<ffffffff810e09bf>] ? percpu_down_read+0x1f/0x50
[18332.878274]  [<ffffffff81208062>] vfs_write+0xa2/0x1a0
[18332.881896]  [<ffffffff812093a6>] SyS_write+0x46/0xa0
[18332.885632]  [<ffffffff810039b7>] do_syscall_64+0x57/0xb0
[18332.889709]  [<ffffffff81883321>] entry_SYSCALL64_slow_path+0x25/0x25
[18332.894727] ---[ end trace 09ebbe31f831ef17 ]---

Fixes: ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: NAlex Vesker <valex@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

There is skb_clone(skb, GFP_KERNEL) in spinlock context
in rxe_rcv_mcast_pkt().

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before.  However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.

Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid.  It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below.  To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NWade Berrier <wberrier@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>