Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In normal operation we see this series of messages as the host drives
the network device:

 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
 ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
 ftgmac100 1e660000.ethernet eth0: NCSI interface down
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI interface up
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
 ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
 ftgmac100 1e660000.ethernet eth0: NCSI interface down
 ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
 ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
 ftgmac100 1e660000.ethernet eth0: NCSI interface up

This makes all of these messages netdev_dbg. They are still useful to
debug eg. misbehaving network device firmware, but we do not need them
filling up the kernel logs in normal operation.
Acked-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the ASPEED datasheet, gigabit speeds require a clock of
100MHz or higher. Other speeds require 25MHz or higher. This patch
configures a 100MHz clock if the system has a direct-attached
PHY, or 25MHz if the system is running NC-SI which is limited to 100MHz.

There appear to be no other upstream users of the FTGMAC100 driver it is
hard to know the clocking requirements of other platforms. Therefore a
conservative approach was taken with enabling clocks. If the platform is
not ASPEED, both requesting the clock and configuring the speed is
skipped.
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Tested-by: NAndrew Jeffery <andrew@aj.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register the ndo_vlan_rx_{add,kill}_vid callbacks and set the
NETIF_F_HW_VLAN_CTAG_FILTER if NCSI is available.
This allows the VLAN core to notify the NCSI driver when changes occur
so that the remote NCSI channel can be properly configured to filter on
the set VLAN tags.
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_napi_del() should be paired with netif_napi_add(), however no
such call takes place in ftgmac100_probe(). This triggers a NULL
pointer dereference if e.g. no PHY is found by the MDIO probe:

	 [ 2.770000] libphy: Fixed MDIO Bus: probed
	 [ 2.770000] ftgmac100 1e660000.ethernet: Generated random MAC address 66:58:c0:5a:50:b8
	 [ 2.790000] libphy: ftgmac100_mdio: probed
	 [ 2.790000] ftgmac100 1e660000.ethernet (unnamed net_device) (uninitialized): eth%d: no PHY found
	 [ 2.790000] ftgmac100 1e660000.ethernet: MII Probe failed!
	 [ 2.810000] Unable to handle kernel NULL pointer dereference at virtual address 00000004
	 [ 2.810000] pgd = 80004000
	 [ 2.810000] [00000004] *pgd=00000000
	 [ 2.810000] Internal error: Oops: 805 [#1] ARM
	 [ 2.810000] CPU: 0 PID: 1 Comm: swapper Not tainted 4.10.17-1a4df30c39cf5ee0e3d2528c409787ccbb4a672a #1
	 [ 2.810000] Hardware name: ASpeed SoC
	 [ 2.810000] task: 9e421b60 task.stack: 9e4a0000
	 [ 2.810000] PC is at netif_napi_del+0x74/0xa4
	 [ 2.810000] LR is at ftgmac100_probe+0x290/0x674
	 [ 2.810000] pc : [<80331004>] lr : [<80292b30>] psr: 60000013
	 [ 2.810000] sp : 9e4a1d70 ip : 9e4a1d88 fp : 9e4a1d84
	 [ 2.810000] r10: 9e565000 r9 : ffffffed r8 : 00000007
	 [ 2.810000] r7 : 9e565480 r6 : 9ec072c0 r5 : 00000000 r4 : 9e5654d8
	 [ 2.810000] r3 : 9e565530 r2 : 00000000 r1 : 00000000 r0 : 9e5654d8
	 [ 2.810000] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
	 [ 2.810000] Control: 00c5387d Table: 80004008 DAC: 00000055
	 [ 2.810000] Process swapper (pid: 1, stack limit = 0x9e4a0188)
	 [ 2.810000] Stack: (0x9e4a1d70 to 0x9e4a2000)
	 [ 2.810000] 1d60: 9e565000 9e549e10 9e4a1dcc 9e4a1d88
	 [ 2.810000] 1d80: 80292b30 80330f9c ffffffff 9e4a1d98 80146058 9ec072c0 00009e10 00000000
	 [ 2.810000] 1da0: 9e549e18 9e549e10 ffffffed 805f81f4 fffffdfb 00000000 00000000 00000000
	 [ 2.810000] 1dc0: 9e4a1dec 9e4a1dd0 80243df8 802928ac 9e549e10 8062cbd8 8062cbe0 805f81f4
	 [ 2.810000] 1de0: 9e4a1e24 9e4a1df0 80242178 80243da4 803001d0 802ffa60 9e4a1e24 9e549e10
	 [ 2.810000] 1e00: 9e549e44 805f81f4 00000000 00000000 805b8840 8058a6b0 9e4a1e44 9e4a1e28
	 [ 2.810000] 1e20: 80242434 80241f04 00000000 805f81f4 80242344 00000000 9e4a1e6c 9e4a1e48
	 [ 2.810000] 1e40: 80240148 80242350 9e425bac 9e4fdc90 9e790e94 805f81f4 9e790e60 805f5640
	 [ 2.810000] 1e60: 9e4a1e7c 9e4a1e70 802425dc 802400d8 9e4a1ea4 9e4a1e80 80240ba8 802425c0
	 [ 2.810000] 1e80: 8050b6ac 9e4a1e90 805f81f4 ffffe000 805b8838 80616720 9e4a1ebc 9e4a1ea8
	 [ 2.810000] 1ea0: 80243068 80240a68 805ab24c ffffe000 9e4a1ecc 9e4a1ec0 80244a38 80242fec
	 [ 2.810000] 1ec0: 9e4a1edc 9e4a1ed0 805ab264 80244a04 9e4a1f4c 9e4a1ee0 8058ae70 805ab258
	 [ 2.810000] 1ee0: 80032c68 801e3fd8 8052f800 8041af2c 9e4a1f4c 9e4a1f00 80032f90 8058a6bc
	 [ 2.810000] 1f00: 9e4a1f2c 9e4a1f10 00000006 00000006 00000000 8052f220 805112f0 00000000
	 [ 2.810000] 1f20: 9e4a1f4c 00000006 80616720 805cf400 80616720 805b8838 80616720 00000057
	 [ 2.810000] 1f40: 9e4a1f94 9e4a1f50 8058b040 8058add0 00000006 00000006 00000000 8058a6b0
	 [ 2.810000] 1f60: 3940bf3d 00000007 f115c2e8 00000000 803fd158 00000000 00000000 00000000
	 [ 2.810000] 1f80: 00000000 00000000 9e4a1fac 9e4a1f98 803fd170 8058af38 00000000 803fd158
	 [ 2.810000] 1fa0: 00000000 9e4a1fb0 8000a5e8 803fd164 00000000 00000000 00000000 00000000
	 [ 2.810000] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
	 [ 2.810000] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 d11dcae8 af8ddec5
	 [ 2.810000] [<80331004>] (netif_napi_del) from [<80292b30>] (ftgmac100_probe+0x290/0x674)
	 [ 2.810000] [<80292b30>] (ftgmac100_probe) from [<80243df8>] (platform_drv_probe+0x60/0xc0)
	 [ 2.810000] [<80243df8>] (platform_drv_probe) from [<80242178>] (driver_probe_device+0x280/0x44c)
	 [ 2.810000] [<80242178>] (driver_probe_device) from [<80242434>] (__driver_attach+0xf0/0x104)
	 [ 2.810000] [<80242434>] (__driver_attach) from [<80240148>] (bus_for_each_dev+0x7c/0xb0)
	 [ 2.810000] [<80240148>] (bus_for_each_dev) from [<802425dc>] (driver_attach+0x28/0x30)
	 [ 2.810000] [<802425dc>] (driver_attach) from [<80240ba8>] (bus_add_driver+0x14c/0x268)
	 [ 2.810000] [<80240ba8>] (bus_add_driver) from [<80243068>] (driver_register+0x88/0x104)
	 [ 2.810000] [<80243068>] (driver_register) from [<80244a38>] (__platform_driver_register+0x40/0x54)
	 [ 2.810000] [<80244a38>] (__platform_driver_register) from [<805ab264>] (ftgmac100_driver_init+0x18/0x20)
	 [ 2.810000] [<805ab264>] (ftgmac100_driver_init) from [<8058ae70>] (do_one_initcall+0xac/0x168)
	 [ 2.810000] [<8058ae70>] (do_one_initcall) from [<8058b040>] (kernel_init_freeable+0x114/0x1cc)
	 [ 2.810000] [<8058b040>] (kernel_init_freeable) from [<803fd170>] (kernel_init+0x18/0x104)
	 [ 2.810000] [<803fd170>] (kernel_init) from [<8000a5e8>] (ret_from_fork+0x14/0x2c)
	 [ 2.810000] Code: e594205c e5941058 e2843058 e3a05000 (e5812004)
	 [ 3.210000] ---[ end trace f32811052fd3860c ]---
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The error paths set err, but it's not returned.

I wondered if we should fix all of the callers to check the returned
value, but Ben explains why the code is this way:

> Most call sites ignore it on purpose. There's nothing we can do if
> we fail to get a buffer at interrupt time, so we point the buffer to
> the scratch page so the HW doesn't DMA into lalaland and lose the
> packet.
>
> The one call site that tests and can fail is the one used when brining
> the interface up. If we fail to allocate at that point, we fail the
> ifup. But as you noticed, I do have a bug not returning the error.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Populate mii_bus->parent with our own platform device before
registering, which makes it easier to locate the MDIO bus
in sysfs when trying to diagnose problems.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We had reports of 50us not being sufficient to reset the MAC,
thus hitting the "Hardware reset failed" error bringing the
interface up on some AST2400 based machines.

This bumps the timeout to 200us.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to ensure the loads from the descriptor are done after the
MMIO store clearing the interrupts has completed, otherwise we
might still miss work.

A read back from the MMIO register will "push" the posted store and
ioread32 has a barrier on weakly aordered architectures that will
order subsequent accesses.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This uses the standard phy-mode property
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just call the interrupt handler with interrupts locally disabled
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports HW vlan tag insertion and extraction. Add support
for it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the ndo_set_rx_mode() callback to configure the
multicast filters, promisc and allmulti options.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hopefully my understanding of how the hardware works is correct,
as the documentation isn't completely clear. So far I have seen
no obvious issue. Pause seem to also work with NC-SI.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A non-wired up implementation accidentally made its way in
a previous patch (Make ring sizes configurable via ethtool).

This removes it and wires up the generic phy_ethtool_nway_reset
instead.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I haven't seen any improvement above that size on the machines
I've tested with.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We set an arbitrary max at 1024 since we pre-allocate the actual
descriptor arrays and skb arrays to the full size to keep the
code a bit simpler and avoid allocation failures in the reset
task.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear stale interrupts on entry, configure FIFO sizes, set FIFO
thresholds, configure interrupt mitigation.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The helpers just take space but don't provide much value. Simple
one line comments are more explanatory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To remove more confusion. This function is about obtaining the
initial MAC address at driver probe time.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To avoid confusion with the ndo callback and generally be
clearer about the purpose of that function
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So features can be turned on/off via ethtool
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.

Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.

Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The documentation describes NETIF_F_IP_CSUM as deprecated
so let's switch to NETIF_F_HW_CSUM and use the helper to
handle unhandled protocols.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Directly access the fields when needed. The accessors add clutter
not clarity and in some cases cause unnecessary read-modify-write
type access on the slow (uncached) descriptor memory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add NETIF_F_SG and create multiple TX ring entries for skb fragments.

On reclaim, the skb is only freed on the segment marked as "last".
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Those are non-cachable stores, let's avoid those we don't need. Remove
the helper, it's not particularly helpful and since it uses "priv"
I can't move it to the header file.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This moves the packet freeing to a separate function
which is also used by ftgmac100_free_buffers() and will
be used more in the error path of fragmented sends.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We'll use variants of this accessor without barriers when
building series of descriptors for fragmented sends
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have a private lock which isn't terribly useful, and we maintain
a "tx_pending" counter for information that's already available
via a trivial arithmetic operation. Then we unconditionaly wake
the queue even when not stopped. Finally our code in tx isn't
really safe vs. a concurrent reclaim. The aspeed chips aren't SMP
today but I prefer the code being right and future proof.

So rip that out and replace it with more "standard" queue handling,
currently with a threshold of 1 queue element, which will be
increased when we implement fragmented sends.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than in the descriptor. The descriptor is mapped non-cachable
and rather slow to access.

Since to do that we need to keep track of the tx "pointer" we also
have no use of all the accesors to manipulate it, just open code
it, it's as clear and will help when adding fragmented sends.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than just transmitting garbage past the end of the small
packet.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a simple goto to a drop path at the tail of the function,
it will be used in a few more cases soon
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will make subsequent rework of the tx path simpler
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move it below ftgmac100_xmit() and the rest of the tx path

No code change.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have a reset task to reset our chip, use it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HW incorrectly calculates the frame size without the vlan
tag and compares that against 64. It will thus flag 64-bytes
frames with a vlan tag as 60-bytes frames "runt" packets
which we'll then drop. Thus we end up dropping ARP packets
on vlan's ...

It does that whether vlan tag stripping is enabled or not.

This works around it by ignoring the "runt" error bit of the
frame has been vlan tagged and is at least 60 bytes.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Directly access the fields when needed. The accessors add clutter
not clarity and in some cases cause unnecessary read-modify-write
type access on the slow (uncached) descriptor memory.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>