Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY drivers don't indicate they support pause. They expect MAC drivers
to enable its support if the MAC has the needed hardware. Thus MAC
drivers should not mask Pause support, but enable it.

Change a few ANDs to ORs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy supported speed is being used to determine if the MAC should
be configured to 100 or 1G. The masking logic is broken. Instead, look
at 1G supported speeds to enable 1G MAC support.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report in standard netdev stats drops and errors as well as
RX multicast from the FW vNIC counters.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed extra characters from the names of structures to unify prefixes
used through the driver code (we normally use hw_atl for hw specifics).
HW_ATL_B0_ and HW_ATL_A0_ are the same and useless copies.
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed extra spaces, corrected alignment.
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support of Energy-Efficient Ethernet to aQuantia NIC's via ethtool
(according to the IEEE 802.3az specifications)
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Tested-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add WOL support. Currently only magic packet
(ethtool -s <ethX> wol g) feature is implemented.

Remove hw_set_power and move that to FW_OPS set_power:
because WOL configuration behaves differently on 1x and 2x
firmwares
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Tested-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added definitions and structures needed to support WOL.
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Tested-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the upload function, which worked incorrectly with
some chips.
Signed-off-by: NYana Esina <yana.esina@aquantia.com>
Signed-off-by: NNikita Danilov <nikita.danilov@aquantia.com>
Tested-by: NNikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the changes in patch 1 and 2, droq lock is not required.
So removing droq lock.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed oom task unconditional rescheduling every 250ms and created per
queue oom work queue for refilling buffers.

The oom task refills only if the available descriptors is fallen to 64.
There will be no packets coming in after hitting this level. So NAPI will
not run until oom task refills the buffers.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Control packets are processed in tasklet when interface is down and in
NAPI when interface is up. So tasklet can be disabled when interface up
and re-enabled when interface is down.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent commit updated vlan_cmd.dropnovlan_fm but failed to remove
the older assignment.  Fix this by removing the former redundant
assignment.

Detected by CoverityScan, CID#1473290 ("Unused value")

Fixes: a89cdd8e ("cxgb4: impose mandatory VLAN usage when non-zero TAG ID")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GMAC >= 4 also supports CBS. Lets enable the TC Ops for these versions.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Essentially reverts commit 8fd75c58 ("i40e: move ethtool
stats boiler plate code to i40e_ethtool_stats.h", 2018-08-30), and
additionally moves the similar code in i40evf into i40evf_ethtool.c.

The code was intially moved from i40e_ethtool.c into i40e_ethtool_stats.h
as a way of better logically organizing the code. This has two problems.
First, we can't have an inline function with variadic arguments on all
platforms. Second, it gave the appearance that we had plans to share
code between the i40e and i40evf drivers, due to having a near copy of
the contents in the i40evf/i40e_ethtool_stats.h file.

Patches which actually attempt to combine or share code between the i40e
and i40evf drivers have not materialized, and are likely a ways off.

Rather than fixing the one function which causes build issues, just move
this code back into the i40e_ethtool.c and i40evf_ethtool.c files. Note
that we also change these functions back from static inlines to just
statics, since they're no longer in a header file.

We can revisit this if/when work is done to actually attempt to share
code between drivers. Alternatively, this stats code could be made more
generic so that it can be shared across drivers as part of ethtool
kernel work.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a non-zero VLAN Tag ID is passed to t4_set_vlan_acl()
then impose mandatory VLAN Usage with that VLAN ID.
I.e any other VLAN ID should result in packets getting
dropped.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 48875222 ("liquidio: Add spoof checking on a VF MAC address")
Signed-off-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As you are already in a tasklet, it is unnecessary to call spin_lock_bh.
Signed-off-by: Njun qian <hangdianqj@163.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both WARN_ON() and WARN_ONCE() already contain an unlikely(), so it's not
necessary to wrap it into another.
Signed-off-by: NIgor Stoppa <igor.stoppa@huawei.com>
Cc: Madalin Bucur <madalin.bucur@nxp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c: In function 'bnxt_tc_parse_flow':
drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c:186:6: warning:
 variable 'addr_type' set but not used [-Wunused-but-set-variable]
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/cavium/liquidio/cn23xx_vf_device.c: In function 'cn23xx_setup_octeon_vf_device':
drivers/net/ethernet/cavium/liquidio/cn23xx_vf_device.c:619:20: warning:
 variable 'ring_flag' set but not used [-Wunused-but-set-variable]
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Provide the API to set/unset the spoof checking feature.
2. Add a function to periodically provide the count of found
   packets with spoof VF MAC address.
3. Prevent VF MAC address changing while the spoofchk of the VF is
   on unless the changing MAC address is issued from PF.
Signed-off-by: NWeilin Chang <weilin.chang@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new qed firmware with fixes and support for new features.

Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix

RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.

ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.

Misc:
- Debug Tools changes.
Signed-off-by: NDenis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VXLAN and GRE FW features have to currently be both advertised
for the driver to enable them.  Separate the handling.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the accesses to rtsyms now all going via special helpers
we can easily make sure the driver is not reading past the
end of the symbol.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NFrancois H. Theron <francois.theron@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ease of debug preface all error messages with the name
of the symbol which caused them.  Use the same message format
for existing messages while at it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NFrancois H. Theron <francois.theron@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return the error and report value through the output param.

Fixes: 640917dd ("nfp: support access to absolute RTsyms")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NFrancois H. Theron <francois.theron@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CHECKSUM_COMPLETE is not applicable to SCTP protocol.
Setting it for SCTP packets leads to CRC32c validation failure.

Fixes: bbceefce ("net/mlx5e: Support RX CHECKSUM_COMPLETE")
Signed-off-by: NAlaa Hleihel <alaa@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In multi-host (MH) NIC scheme, a single HW port serves multiple hosts
or sockets on the same host.
The HW uses a mechanism in the PCIe buffer which monitors
the amount of consumed PCIe buffers per host.
On a certain configuration, under congestion,
the HW emulates a switch doing ECN marking on packets using ECN
indication on the completion descriptor (CQE).

The driver needs to set the ECN bits on the packet SKB,
such that the network stack can react on that, this commit does that.
Signed-off-by: NNatali Shechtman <natali@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Changed "priv.clock.lock" lock from 'rw_lock' to 'seq_lock'
in order to improve packet rate performance.

Tested on Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz.
Sent 64b packets between two peers connected by ConnectX-5,
and measured packet rate for the receiver in three modes:
	no time-stamping (base rate)
	time-stamping using rw_lock (old lock) for critical region
	time-stamping using seq_lock (new lock) for critical region
Only the receiver time stamped its packets.

The measured packet rate improvements are:

	Single flow (multiple TX rings to single RX ring):
		without timestamping:	  4.26 (M packets)/sec
		with rw-lock (old lock):  4.1  (M packets)/sec
		with seq-lock (new lock): 4.16 (M packets)/sec
		1.46% improvement

	Multiple flows (multiple TX rings to six RX rings):
		without timestamping: 	  22   (M packets)/sec
		with rw-lock (old lock):  11.7 (M packets)/sec
		with seq-lock (new lock): 21.3 (M packets)/sec
		82.05% improvement

The packet rate improvement is due to the lack of atomic operations
for the 'readers' by the seq-lock.
Since there are much more 'readers' than 'writers' contention
on this lock, almost all atomic operations are saved.
this results in a dramatic decrease in overall
cache misses.
Signed-off-by: NShay Agroskin <shayag@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Not all profiles query the HW Q counters in update_stats() callback.
HW Q couners are limited per device and in case of representors all
their Q counters are allocated on the parent PF device.
Avoid reundant allocation of HW Q counters by moving the allocation
to init_rx profile callback.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Move the definition of mlx5e_priv_flags into en_ethtool.c because it's
only used there.

Fixes: 4e59e288 ("net/mlx5e: Introduce net device priv flags infrastructure")
Signed-off-by: NKamal Heib <kamalheib1@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Previous patch in series changed flow counter storage structure from
rb_tree to linked list in order to improve flow counter traversal
performance. The drawback of such solution is that flow counter lookup by
id becomes linear in complexity.

Store pointers to flow counters in idr in order to improve lookup
performance to logarithmic again. Idr is non-intrusive data structure and
doesn't require extending flow counter struct with new elements. This means
that idr can be used for lookup, while linked list from previous patch is
used for traversal, and struct mlx5_fc size is <= 2 cache lines.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to improve performance of flow counter stats query loop that
traverses all configured flow counters, replace rb_tree with double-linked
list. This change improves performance of traversing flow counters by
removing the tree traversal. (profiling data showed that call to rb_next
was most top CPU consumer)

However, lookup of flow flow counter in list becomes linear, instead of
logarithmic. This problem is fixed by next patch in series, which adds idr
for fast lookup. Idr is to be used because it is not an intrusive data
structure and doesn't require adding any new members to struct mlx5_fc,
which allows its control data part to stay <= 1 cache line in size.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters is added to struct mlx5_fc_stats. Lockless
NULL-terminated single linked list data type is used due to following
reasons:
 - This use case only needs to add single element to list and
 remove/iterate whole list. Lockless list doesn't require any additional
 synchronization for these operations.
 - First cache line of flow counter data structure only has space to store
 single additional pointer, which precludes usage of double linked list.

Remove flow counter 'deleted' flag that is no longer needed.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters will be added to struct mlx5_fc_stats. However,
the flow counter structure itself has no space left to store any more data
in first cache line. To free space that is needed to store additional list
node, convert current addlist double linked list (two pointers per node) to
atomic single linked list (one pointer per node).

Lockless NULL-terminated single linked list data type doesn't require any
additional external synchronization for operations used by flow counters
module (add single new element, remove all elements from list and traverse
them). Remove addlist_lock that is no longer needed.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>