Remove "label" properties from the LEDs device tree nodes, since
we don't have nice labels on the PCB.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add HDMI support to the HiHope RZ/G2[MN] mother board common
dtsi.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the HDMI encoder to the R8A774A1 DT in disabled state.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the dynamic power coefficient of A57 and A53 CPUs.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Setup a thermal zone driven by SoC temperature sensor. Create passive trip
points and bind them to CPUFreq cooling device that supports power
extension.

Based on work by Dien Pham <dien.pham.ry@renesas.com> for r8a7796 SoC.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Set the capacity-dmips-mhz for RZ/G2M(r8a774a1) SoC, that is based on
dhrystone.

Based on work done by Gaku Inami <gaku.inami.xw@bp.renesas.com> for
r8a7796 SoC.

The average dhrystone result for 5 iterations is as below:

r8a774a1 SoC (CA57x2 + CA53x4)
  CPU   max-freq   dhrystone
  ---------------------------------
  CA57   1500 MHz  11428571 lps/s
  CA53   1200 MHz   5000000 lps/s

From this, CPU capacity-dmips-mhz for CA57 and CA53 are calculated
as follows:

r8a774a1 SoC
  CA57 : 1024 / (11428571 / 1500) * (11428571 / 1500) = 1024
  CA53 : 1024 / (11428571 / 1500) * ( 5000000 / 1200) =  560

Since each CPUs have different max frequencies, the final CPU
capacities of A53 scaled by the above difference is as below

$ cat /sys/devices/system/cpu/cpu*/cpu_capacity
1024
1024
448
448
448
448
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds the "cpu-map" into r8a774a1 composed of multi-cluster. This
definition is used to parse the cpu topology.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> for r8a7796 SoC.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds LEDs support to the HiHope RZ/G2[MN] Main Board
common device tree.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables USB3.0 host/peripheral device node for the HiHope
RZ/G2M board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add USB 2.0 support to the HiHope RZ/G2M.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Similarly to what done for the r8a7796 with commit 737e05bf
("arm64: dts: renesas: revise properties for R-Car Gen3 SoCs'
usb 2.0"), this patch lists the clock for the USB High-Speed Module
(HS-USB) with the USB2.0 Host (EHCI/OHCI) IP DT node, and it lists
the clock for the USB2.0 Host IP with the HS-USB module DT node.

Fixes: 4c2c2fb9 ("arm64: dts: renesas: r8a774a1: Add USB2.0 phy and host(EHCI/OHCI) device nodes")
Fixes: ed898d4f ("arm64: dts: renesas: r8a774a1: Add USB-DMAC and HSUSB device nodes")
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds TMU[01234] device tree nodes to the r8a774a1
SoC specific DT.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds the CMT[0123] device tree nodes to the
r8a774a1 SoC specific DT.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds uSD and eMMC support to the HiHope RZ/G2M
board.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since the R8A77990 SoC uses DU{0,1}, the range from the base address to
the 0x4000 address is used.
This patch fixed it.

Fixes: 13ee2bfc ("arm64: dts: renesas: r8a77990: Add display output support")
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables TI HD3SS3220 device and support usb role switch
for the CAT 874 platform.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables USB3.0 host/peripheral device node for the cat874
board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the new renesas,companion property to the LVDS0 node to point to the
companion LVDS encoder LVDS1.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NJacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: NJacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Enable RWDT and use 60 seconds as default timeout.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables PCIEC[01] PCI express controller on the sub board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Declare pcie bus clock, since it is generated on the HiHope RZ/G2M main
board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds PCIe{0,1} device nodes for R8A774A1 SoC.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The HiHope RZ/G2M sub board sits below the HiHope RZ/G2M main board.
This patch also adds ethernet support along with a dtsi common to
both HiHope RZ/G2M and RZ/G2N sub boards.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NChris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch adds pincontrol support to scif2/scif clock.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NChris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Basic support for the HiHope RZ/G2M main board:
  - Memory,
  - Main crystal,
  - Serial console

This patch also includes a dtsi common to both HiHope RZ/G2M
and RZ/G2N main boards.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NChris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The RZ/G2M (a.k.a. r8a774a1) comes with two clusters of
processors, similarly to the r8a7796.
The first cluster is made of A57s, the second cluster is
made of A53s.

The operating points for the cluster with the A57s are:

 Frequency | Voltage
-----------|---------
 500 MHz   | 0.82V
 1.0 GHz   | 0.82V
 1.5 GHz   | 0.82V

The operating points for the cluster with the A53s are:

 Frequency | Voltage
-----------|---------
 800 MHz   | 0.82V
 1.0 GHz   | 0.82V
 1.2 GHz   | 0.82V

This patch adds the definitions for the operating points
to the SoC specific DT.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NChris Paterson <Chris.Paterson2@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the dynamic power coefficient of A53 CPUs.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.

In R-Car Gen3, IPA is supported for only one channel
Reason:
  Currently, IPA controls base on only CPU temperature.
  And only one thermal channel is assembled closest
  CPU cores is selected as target of IPA.
  If other channels are used, IPA controlling is not properly.

A single cooling device is described for all A53 CPUs as this
reflects that physically there is only one cooling device present.

This patch improves on an earlier version by:

* Omitting cooling-max-level and cooling-min-level properties which
  are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
  property.
* Defers adding dynamic-power-coefficient properties to a separate patch as
  these are properties of the CPU.

The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: NDien Pham <dien.pham.ry@renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the dynamic power coefficient of A57 and A53 CPUs.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.

In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
  Currently, IPA controls base on only CPU temperature.
  And only one thermal channel is assembled closest
  CPU cores is selected as target of IPA.
  If other channels are used, IPA controlling is not properly.

The A57 cooling device supports 5 cooling states which can be categorised
as follows:

0 & 1) boost (clocking up)
2)     default
3 & 4) cooling (clocking down)

Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.

A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.

This patch improves on an earlier version by:

* Omitting cooling-max-level and cooling-min-level properties which
  are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
  property.
* Using cooling-device indexes such that maximum refers to maximum cooling
  rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
  these are properties of the CPU.

The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: NDien Pham <dien.pham.ry@renesas.com>
Signed-off-by: NAn Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the dynamic power coefficient of A57 and A53 CPUs.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.

In R-Car Gen3, IPA is supported for only one channel
 (on H3/M3/M3N SoCs, it is channel THS3). Reason:
  Currently, IPA controls base on only CPU temperature.
  And only one thermal channel is assembled closest
  CPU cores is selected as target of IPA.
  If other channels are used, IPA controlling is not properly.

The A57 cooling device supports 5 cooling states which can be categorised
as follows:

0 & 1) boost (clocking up)
2)     default
3 & 4) cooling (clocking down)

Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.

A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.

This patch improves on an earlier version by:

* Omitting cooling-max-level and cooling-min-level properties which
  are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
  property.
* Using cooling-device indexes such that maximum refers to maximum cooling
  rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
  these are properties of the CPU.

The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: NDien Pham <dien.pham.ry@renesas.com>
Signed-off-by: NHien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: NAn Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Describe the dynamic power coefficient of A57 and A53 CPUs.

Based on work by Gaku Inami <gaku.inami.xw@bp.renesas.com> and others.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.

In R-Car Gen3, IPA is supported for only one channel
(on H3/M3/M3N SoCs, it is channel THS3). Reason:
  Currently, IPA controls base on only CPU temperature.
  And only one thermal channel is assembled closest
  CPU cores is selected as target of IPA.
  If other channels are used, IPA controlling is not properly.

The A5 cooling device supports 5 cooling states which can be categorised as
follows:

0 & 1) boost (clocking up)
2)     default
3 & 4) cooling (clocking down)

Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.

A single cooling device is described for all A57 CPUs and a separate
cooling device is described for all A53 CPUs. This reflects that physically
there is only one cooling device present for each type of CPU.

This patch improves on an earlier version by:

* Omitting cooling-max-level and cooling-min-level properties which
  are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
  property.
* Using cooling-device indexes such that maximum refers to maximum cooling
  rather than the inverse.
* Defers adding dynamic-power-coefficient properties to a separate patch as
  these are properties of the CPU.

The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.
Signed-off-by: NDien Pham <dien.pham.ry@renesas.com>
Signed-off-by: NKeita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: NHien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: NAn Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Since the commit 233da2c9 ("dt-bindings: phy: rcar-gen3-phy-usb2:
Revise #phy-cells property") revised the #phy-cells, this patch follows
the updated document for R-Car Gen3 and RZ/A2 SoCs.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

It is incorrect to specify the no-ether-link property for the AVB device on
the Ebisu board. This is because the property should only be used when a
board does not provide a proper AVB_LINK signal. However, the Ebisu board
does provide this signal.

As per 87c059e9 ("arm64: dts: renesas: salvator-x: Remove renesas,
no-ether-link property") this fixes a bug:

    Steps to reproduce:
    - start AVB TX stream (Using aplay via MSE),
    - disconnect+reconnect the eth cable,
    - after a reconnection the eth connection goes iteratively up/down
      without user interaction,
    - this may heal after some seconds or even stay for minutes.

    As the documentation specifies, the "renesas,no-ether-link" option
    should be used when a board does not provide a proper AVB_LINK signal.
    There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
    and ULCB starter kits since the AVB_LINK is correctly handled by HW.

    Choosing to keep or remove the "renesas,no-ether-link" option will have
    impact on the code flow in the following ways:
    - keeping this option enabled may lead to unexpected behavior since the
      RX & TX are enabled/disabled directly from adjust_link function
      without any HW interrogation,
    - removing this option, the RX & TX will only be enabled/disabled after
      HW interrogation. The HW check is made through the LMON pin in PSR
      register which specifies AVB_LINK signal value (0 - at low level;
      1 - at high level).

    In conclusion, the present change is also a safety improvement because
    it removes the "renesas,no-ether-link" option leading to a proper way
    of detecting the link state based on HW interrogation and not on
    software heuristic.

Fixes: 8441ef64 ("arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB")
Signed-off-by: NTakeshi Kihara <takeshi.kihara.df@renesas.com>
[simon: updated changelog]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Apparently this DTS crossed over with commit 31af04cd ("arm64: dts:
Remove inconsistent use of 'arm,armv8' compatible string") and missed
out on the cleanup, so put it right.
Signed-off-by: NRobin Murphy <robin.murphy@arm.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Convert bootargs from ip=dhcp to ip=on
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables BT support for the CAT874 board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This patch enables WLAN support for the CAT874 board.
Signed-off-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>