There were several strings found without line feeds, fix
them by adding a line feed, as is typical.  Without this
lotsofmessagescanbejumbledtogether.

This patch has known checkpatch warnings from long lines
for the NL_* messages, because checkpatch doesn't know
how to ignore them.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the PF VFs MDD event message to rate limit once per second and
report the total number Rx|Tx event count. Add support to print pending
MDD events that occur during the rate limit. The use of net_ratelimit did
not allow for per VF Rx|Tx granularity.

Additional PF MDD log messages are guarded by netif_msg_[rx|tx]_err().

Since VF RX MDD events disable the queue, add ethtool private flag
mdd-auto-reset-vf to configure VF reset to re-enable the queue.

Disable anti-spoof detection interrupt to prevent spurious events
during a function reset.

To avoid race condition do not make PF MDD register reads conditional
on global MDD result.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fallthrough comments are used to explicitly indicate the code is intended
to flow from one case statement to the next in a switch statement rather
than break out of the switch statement.  They are only needed when a case
has one or more statements to execute before falling through to the next
case, not when there is a list of cases for which the same statement(s)
should be executed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when we enable/disable all Rx queues we do the following
sequence for each Rx queue and then move to the next queue.

1. Enable/Disable the Rx queue via register write.
2. Read the configuration register to determine if the Rx queue was
enabled/disabled successfully.

In some cases enabling/disabling queue 0 fails because of step 2 above.
Fix this by doing step 1 for all of the Rx queues and then step 2 for
all of the Rx queues.

Also, there are cases where we enable/disable a single queue (i.e.
SR-IOV and XDP) so add a new function that does step 1 and 2 above with
a read flush in between.

This change also required a single Rx queue to be enabled/disabled with
and without waiting for the change to propagate through hardware. Fix
this by adding a boolean wait flag to the necessary functions.

Also, add the keywords "one" and "all" to distinguish between
enabling/disabling a single Rx queue and all Rx queues respectively.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool.  Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe.  This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Display all of the supported and advertised link modes based on the PHY
capability with media.

Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide support to change or retrieve RSS hash options for a flow type.
The supported flow-types are: tcp4, tcp6, udp4, udp6, sctp4, sctp6.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Check for all unused parameters, if ethtool sent one of them,
print info about that and return error.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.

There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.

Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().

This patch is generated using following script:

EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"

git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do

	if [[ "$file" =~ $EXCLUDE_FILES ]]; then
		continue
	fi
	sed -i  -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.comCo-developed-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net

Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively.  Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.

Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.

For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: NUsha Ketineni <usha.k.ketineni@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ethtool -m support to read eeprom data from SFP/QSFP modules.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.

Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.

In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.

This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
  network stack is expecting the NET_SKB_PAD to be provided and
  NET_IP_ALIGN can have a non-zero value (these can be typically equal
  to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
  buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
  buffer is implying the need for order 1 page, so that our page
  recycling scheme can still be applied;

With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.

In the followup patch the headroom/tailroom computation logic will be
introduced.

This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add zero copy AF_XDP support.  This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: NKrzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit.  Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Attempt to request an optional device-specific DDP package file
(one with the PCIe Device Serial Number in its name so that different DDP
package files can be used on different devices). If the optional package
file exists, download it to the device. If not, download the default
package file.

Log an appropriate message based on whether or not a DDP package
file exists and the return code from the attempt to download it to the
device.  If the download fails and there is not already a package file on
the device, go into "Safe Mode" where some features are not supported.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The FW build id is currently being displayed as an int which doesn't make
sense. Instead display FW build id as a hex value. Also add other useful
information to the output such as NVM version, API patch info, and FW
build hash.
Signed-off-by: NLukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an additional boolean parameter to the ice_init_dcb
function.  This boolean controls if the LLDP MIB change
events are registered for.  Also, add a new function
defined ice_cfg_lldp_mib_change.  The additional function
is necessary to be able to register for LLDP MIB change
events after calling ice_init_dcb.  The net effect of these
two changes is to allow a delayed registration for MIB change
events so that the driver is not accepting events before it
is ready for them.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver has supported a transmit work limit
that was configurable from ethtool for a long time, but
there are no good use cases for having it be a variable
that can be changed at run time.  In addition, this
variable was noted to be causing performance overhead
due to cache misses.

Just remove the variable and let the code use a constant
so that the functionality is maintained (a limit on the
number of transmits that will be cleaned in any one call
to the clean routines) without the cache miss.

Removes code, removes a variable, removes testing surface. Yay.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the user sets an odd value for [tx|rx]-usecs we align the
value because the hardware only understands ITR values in multiples of
2. This seems misleading because we are essentially telling the user
that the ITR value is odd, when in fact we have changed it internally.
Fix this by reporting that setting odd ITR values is not allowed.

Also, while making changes to ice_set_rc_coalesce() I noticed a bit of
code/error duplication. Make the necessary changes to remove the
duplication.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Users expect ethtool statistics to be updated on-demand when invoking
'ethtool -S <iface>' instead of providing a snapshot of statistics taken
once a second (the frequency of the watchdog task where stats are currently
updated).  Update stats every time 'ethtool -S <iface>' is run.

Also, fix an indentation style issue and an unnecessary local variable
initialization in ice_get_ethtool_stats() discovered while investigating
the subject issue.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current flag name of "enable-fw-lldp" is a bit cumbersome.

Change priv-flag name to "fw-lldp-agent" with a value of on or
off.  This is more straight-forward in meaning.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When ETHTOOL_GLINKSETTINGS is defined get pause param pause->autoneg
reports SW configured setting, however when not defined get pause param
pause->autoneg reports the link status. Set pause param needs to compare
pause->autoneg with the same source as get pause param to block the user
from changing autoneg with the set pause param option, or the user
may be incorrectly blocked from changing Rx|Tx pause settings.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for reporting link partner advertising when
ETHTOOL_GLINKSETTINGS defined. Get pause param reports the Tx/Rx
pause configured, and then ethtool issues ETHTOOL_GSET ioctl and
ice_get_settings_link_up reports the negotiated Tx/Rx pause. Negotiated
pause frame report per IEEE 802.3-2005 table 288-3.

$ ethtool --show-pause ens6f0
Pause parameters for ens6f0:
Autonegotiate:  on
RX:             on
TX:             on
RX negotiated:  on
TX negotiated:  on

$ ethtool ens6f0
Settings for ens6f0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Supported FEC modes: None BaseR RS
        Advertised link modes:  25000baseCR/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: None BaseR RS
        Link partner advertised link modes:  Not reported
        Link partner advertised pause frame use: Symmetric
        Link partner advertised auto-negotiation: Yes
        Link partner advertised FEC modes: Not reported
        Speed: 25000Mb/s
        Duplex: Full
        Port: Direct Attach Copper
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x00000007 (7)
                               drv probe link
        Link detected: yes

When ETHTOOL_GLINKSETTINGS is not defined, get pause param reports the
negotiated Tx/Rx pause.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch mostly capitalizes abbreviations in code comments. Fixed some
typos and removed some unnecessary newlines as well.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add call to configure dropping egress LLDP packets in ice_vsi_setup
and remove the rule in ice_vsi_release.

Add calls to add/remove rule to route LLDP packets to default VSI when
FW LLDP engine is disabled/enabled and remove rule if applied during
ice_vsi_release.

In the function ice_add_eth_mac(), there is a line that hard codes the
filter info flag to TX. This is incorrect as this flag will be set by
the calling function that built the list of filters to add. So remove
the hard coded value.

This patch also contains a fix to stop treating the DCBx state of
"Not Started" as an error state that kicks DCB in SW mode. This will
address having non-cabled interfaces automatically go into SW mode
with the FW engine running.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds driver support for Forward Error Correction (FEC)
and ethtool handlers to set/get FEC params.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the path for re-enabling FW LLDP engine, there is
a call to register for LLDP MIB change events.  This
call is redundant, in that the call to ice_pf_dcb_cfg
will already register the driver for these events.  Also,
the call as it stands now is too early in the flow before
before DCB is configured.

Remove the redundant call.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we have two MSI-x (IRQ) trackers, one for OS requested MSI-x
entries (sw_irq_tracker) and one for hardware MSI-x vectors
(hw_irq_tracker). Generally the sw_irq_tracker has less entries than the
hw_irq_tracker because the hw_irq_tracker has entries equal to the max
allowed MSI-x per PF and the sw_irq_tracker is mainly the minimum (non
SR-IOV portion of the vectors, kernel granted IRQs). All of the non
SR-IOV portions of the driver (i.e. LAN queues, RDMA queues, OICR, etc.)
take at least one of each type of tracker resource. SR-IOV only grabs
entries from the hw_irq_tracker. There are a few issues with this approach
that can be seen when doing any kind of device reconfiguration (i.e.
ethtool -L, SR-IOV, etc.). One of them being, any time the driver creates
an ice_q_vector and associates it to a LAN queue pair it will grab and
use one entry from the hw_irq_tracker and one from the sw_irq_tracker.
If the indices on these does not match it will cause a Tx timeout, which
will cause a reset and then the indices will match up again and traffic
will resume. The mismatched indices come from the trackers not being the
same size and/or the search_hint in the two trackers not being equal.
Another reason for the refactor is the co-existence of features with
SR-IOV. If SR-IOV is enabled and the interrupts are taken from the end
of the sw_irq_tracker then other features can no longer use this space
because the hardware has now given the remaining interrupts to SR-IOV.

This patch reworks how we track MSI-x vectors by removing the
hw_irq_tracker completely and instead MSI-x resources needed for SR-IOV
are determined all at once instead of per VF. This can be done because
when creating VFs we know how many are wanted and how many MSI-x vectors
each VF needs. This also allows us to start using MSI-x resources from
the end of the PF's allowed MSI-x vectors so we are less likely to use
entries needed for other features (i.e. RDMA, L2 Offload, etc).

This patch also reworks the ice_res_tracker structure by removing the
search_hint and adding a new member - "end". Instead of having a
search_hint we will always search from 0. The new member, "end", will be
used to manipulate the end of the ice_res_tracker (specifically
sw_irq_tracker) during runtime based on MSI-x vectors needed by SR-IOV.
In the normal case, the end of ice_res_tracker will be equal to the
ice_res_tracker's num_entries.

The sriov_base_vector member was added to the PF structure. It is used
to represent the starting MSI-x index of all the needed MSI-x vectors
for all SR-IOV VFs. Depending on how many MSI-x are needed, SR-IOV may
have to take resources from the sw_irq_tracker. This is done by setting
the sw_irq_tracker->end equal to the pf->sriov_base_vector. When all
SR-IOV VFs are removed then the sw_irq_tracker->end is reset back to
sw_irq_tracker->num_entries. The sriov_base_vector, along with the VF's
number of MSI-x (pf->num_vf_msix), vf_id, and the base MSI-x index on
the PF (pf->hw.func_caps.common_cap.msix_vector_first_id), is used to
calculate the first HW absolute MSI-x index for each VF, which is used
to write to the VPINT_ALLOC[_PCI] and GLINT_VECT2FUNC registers to
program the VFs MSI-x PCI configuration bits. Also, the sriov_base_vector
is used along with VF's num_vf_msix, vf_id, and q_vector->v_idx to
determine the MSI-x register index (used for writing to GLINT_DYN_CTL)
within the PF's space.

Interrupt changes removed any references to hw_base_vector, hw_oicr_idx,
and hw_irq_tracker. Only sw_base_vector, sw_oicr_idx, and sw_irq_tracker
variables remain. Change all of these by removing the "sw_" prefix to
help avoid confusion with these variables and their use.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a handler for ethtool selftest. Selftest includes
testing link, interrupts, eeprom, registers and packet loopback.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes ethtool -S reported stats in ice driver to match
format and nomenclature of the ixgbe driver.
Signed-off-by: NRichard Rodriguez <richard.rodriguez@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>