The bnx2x_select_queue() was using __skb_tx_hash() to select the
transmit queue, totally ignoring XPS settings, while XPS can help
performance quite significantly, so change the bnx2x_select_queue()
to use __dev_pick_tx() instead which will use XPS if configured.

Based on patches from Ying Cai and Havard Skinnemoen
Reported-by: Ngovindarajulu.v <govindarajulu90@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Ying Cai <ycai@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forcing uninitialized state allows us to upgrade and reinitialize the adapter.

FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
At this point driver supports above and greater than above version of firmware.
If it doesn't find the required firmware version than it forces the adapter to
be reinitialized as shown below.

1) If FW_ON_ADAPTER < FW_VERSION and we're the MASTER_PF force uninitialized
   state and a FW upgrade if available.

       - If FW_ON_ADAPTER < /lib/firmware/cxgb4/t*fw.bin we will update the
         adapters FW.
       - If FW_ON_ADAPTER >= /lib/firmware/cxgb4/t*fw.bin don't upgrade FW.
       - If upgrade_fw() fails force reinitialization of the adapter anyways,
         it might still work.

   Either way forcing the uninitialized state allows cxgb4 reinitialize FW.

2) If FW_ON_ADAPTER >= FW_VERSION driver follows normal path.
Signed-off-by: NJay Hernandez <jay@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Allwinner A10 has an ethernet controller that seem to be developped
internally by them.

The exact feature set of this controller is unknown, since there is no
public documentation for this IP, and this driver is mostly the one
published by Allwinner that has been heavily cleaned up.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_enable_device() will set device power state to D0,
so it's no need to do it again in tulip_init_one().
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_enable_device() will set device power state to D0,
so it's no need to do it again in qlcnic_attach_func().
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_enable_device() will set device power state to D0,
so it's no need to do it again in jme_init_one().
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds device tree parsing support for the shared driver of mv643xx_eth.
As the bindings are slightly different from current PPC bindings new binding
documentation is also added. Following PPC-style device setup, the shared
driver now also adds port platform_devices and sets up port platform_data.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet controllers found on Kirkwood SoCs not only suffer from loosing
MAC address register contents on clock gating but also some important
registers are reset to values that would break ethernet. This patch
clears the CLK125_BYPASS_EN bit for DT enabled Kirkwood only by using
of_device_is_compatible() instead of #ifdefs. Non-DT Kirkwood is not
affected as it installs a clock gating workaround because of the MAC
address issue above. Other Orion SoCs do not suffer from register reset,
do not have the bit in question, or do not have the register at all.
Moreover, system controllers on PPC using this driver should also be
protected from clearing that bit.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This connects to a phy node passed to the port device instead of probing
the phy by phy_addr.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of managed devm_ioremap and remove corresponding iounmap.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using a separated mdio bus driver with mvmdio, phy_detach on network device
removal will not stop the phy and finally lead to NULL pointer dereference
in mvmdio due to non-existent network device. Use phy_disconnect instead
to properly stop phy device from accessing network device prior removal of
the network device.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct email address and years.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable emaclite for Xilinx ARM Zynq platform.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Emaclite can be used on ARM zynq where in_be32/out_be32 IO
functions are not present. Use standard __raw_readl/__raw_writel
IO functions instead.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

xemaclite_adjust_link is used locally.
It removes sparse warning:
drivers/net/ethernet/xilinx/xilinx_emaclite.c:916:6: warning:
symbol 'xemaclite_adjust_link' was not declared. Should it be static?
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For system which contains at least two ethernet IP where
one IP manage MDIO bus with several PHYs.

Example dts node:
ethernet_mac0: ethernet@81000000 {
	compatible = "xlnx,xps-ethernetlite-1.00.a";
	device_type = "network";
	interrupt-parent = <&xps_intc_0>;
	interrupts = < 1 0 >;
		local-mac-address = [ 00 0a 35 00 db bb ];
	phy-handle = <&ethernet_mac0_phy0>;
	reg = < 0x81000000 0x10000 >;
	xlnx,duplex = <0x1>;
	xlnx,family = "spartan3e";
	xlnx,include-internal-loopback = <0x0>;
	xlnx,include-mdio = <0x1>;
	xlnx,rx-ping-pong = <0x0>;
	xlnx,tx-ping-pong = <0x0>;
	ethernet_mac0_mdio {
		#address-cells = <1>;
		#size-cells = <0>;
		ethernet_mac0_phy0: phy@1 {
			reg = <0x1>;
		} ;
		ethernet_mac0_phy1: phy@3 {
			reg = <0x3>;
		} ;
	} ;
} ;
ethernet_mac2: ethernet@81040000 {
	compatible = "xlnx,xps-ethernetlite-1.00.a";
	device_type = "network";
	interrupt-parent = <&xps_intc_0>;
	interrupts = < 11 0 >;
		local-mac-address = [ 00 0a 35 00 db bb ];
	phy-handle = <&ethernet_mac0_phy1>;
	reg = < 0x81040000 0x10000 >;
	xlnx,duplex = <0x1>;
	xlnx,family = "spartan3e";
	xlnx,include-internal-loopback = <0x0>;
	xlnx,include-mdio = <0x0>;
	xlnx,rx-ping-pong = <0x0>;
	xlnx,tx-ping-pong = <0x0>;
} ;
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be more verbose when any problem happens.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Adapters do not support co-existence of INTx Interrupt with
  MSI-X or MSI among multiple functions. Prevent attaching
  of a function during normal load, if adapter gets into mixed
  mode of interrupts
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o log "Unknown" board name and "Unknown" serial number in case
  of mismatched adapter type found. This will avoid weird characters
  logs when an adapter is in bad state or corrupted.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->transport_header
will be an offset from head. This is corrected by using wrappers that
ensure that comparisons and calculations are always made using pointers.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>

v2->v3: fix typo on simeth
	shortened dev_getter
	shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d063
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to save power, let's disable the regulator in the suspend function and
enable it in resume.

Tested on a mx28evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe the clocks are enabled prior than the acquiring the interrupts.

In the remove function we need to do the opposite: first remove the interrupts
and then disable the clocks.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case of error during probe, disable the PHY regulator.

Do the same in fec_drv_remove().
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when fec_enet_init fails it jumps to 'failed_init' error path, which
will attemp to free the interrupts.

This is wrong because at this point the interrupts have not even been acquired.

Swap failed_init/failed_irq to fix the error path.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().

This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: NKalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.

This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the PCI shutdown callback to support un-orderly shutdown, i.e.,
shutdowns in which the remove callback will not be called.

Due to the lack of this functionality, when an un-orderly shutdown occurred,
it was possible for wake-on-lan to remain disabled.

This is now fixed as the callback introduces the correct place in which
`system_state' can be queried and wake-on-lan be configured accordingly.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0eb43b4b
"bnx2x, bnx2fc: Use per port max exchange resources" has changed the number
of available FCoE exchanges, even in scenarios when some of the functions has
no FCoE support; This needlessly degraded the available resources.

Remedy this by calculating the maximal number of functions that may actually
utilize said connection.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A PF should ack the firmware when receiving unknown messages through the VF's
mailbox. This prevents the VF mailbox from being stuck in case of a VF sending
a message unknown to the PF (e.g. VF with more advanced version).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>