New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds CM3 memory map.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

per queue coalescing allows better and more finegrained control
over interrupt rates.
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

handle netpoll case when qede_poll is called by
netpoll layer with budget 0
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, a random stack value is being returned because variable
_ret_ is not properly initialized. This variable is actually not
used anymore and it should be removed.

Fix this by removing all instances of variable ret and return 0.

Fixes: 64749c9c ("net: hns3: remove redundant return value of hns3_uninit_all_ring()")
Addresses-Coverity-ID: 1501700 ("Uninitialized scalar variable")
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

plat_dat is initialized by stmmac_probe_config_dt().
So, initialization is not required by priv->plat.
This removes unnecessary initialization and variables.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this warning:
WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stats_lock is no longer used. So remove it.
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several spinlock_t definitions without comments.
Add them.
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following checkpatch checks:
CHECK: Macro argument 'off' may be better as '(off)' to
avoid precedence issues
CHECK: Alignment should match open parenthesis
CHECK: multiple assignments should be avoided
CHECK: Blank lines aren't necessary before a close brace '}'
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: Unnecessary parentheses around 'rc != H_FUNCTION'
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: Avoid multiple line dereference
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: networking block comments don't use an empty /* line, use /* Comment...
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following checkpatch warnings:
WARNING: Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
WARNING: Prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return negative error code -ENOMEM from the ioremap() error
handling case instead of 0, as done elsewhere in this function.

Fixes: 1958fc2f ("net/mlx5: SF, Add auxiliary device driver")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Fix to return negative error code from the mlx5e_tc_tun_init() error
handling case instead of 0, as done elsewhere in this function.

This commit also using 0 instead of 'ret' when success since it is
always equal to 0.

Fixes: 8914add2 ("net/mlx5e: Handle FIB events to update tunnel endpoint device")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

The mlx5_chains_get_table() function doesn't return NULL, it returns
error pointers so we need to fix this condition.

Fixes: 34ca6535 ("net/mlx5: E-Switch, Indirect table infrastructure")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NVlad Buslov <vladbu@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Exclude contents of tc_tun.h header when CONFIG_MLX5_ESWITCH is disabled to
prevent compile-time errors when compiling with such config.

Fixes: 0d9f9647 ("net/mlx5e: Extract tc tunnel encap/decap code to dedicated file")
Signed-off-by: NVlad Buslov <vladbu@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Fix the following coccicheck warnings:

./drivers/net/ethernet/mellanox/mlx5/core/fs_core.c:575:2-14: WARNING:
Assignment of 0/1 to bool variable.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NJiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

There is a spelling mistake in a netdev_warn message. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

There is a spelling mistake in a netdev_warn message. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Remove including <generated/utsrelease.h> that don't need it.

Fixes: 17a7612b ("net/mlx5_core: Clean driver version and name")
Signed-off-by: NZou Wei <zou_wei@huawei.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

There are some spelling mistakes in the Kconfig. Fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

This entry used when skipping the parser needed,
for example, the custom header pretended to ethernet header.
Suggested-by: NLiron Himi <liron@marvell.com>
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register set_link_ksetting callback with driver such that
link configurations parameters like advertised mode,speed, duplex
and autoneg can be configured.

below command
ethtool -s eth0 advertise 0x1 speed 10 duplex full autoneg on
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register get_link_ksettings callback to get link status information
from the driver. As virtual function (vf) shares same physical link
same API is used for both the drivers and for loop back drivers
simply returns the fixed values as its does not have physical link.

ethtool eth3
Settings for eth3:
        Supported ports: [ ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
                                10000baseKR/Full
                                1000baseX/Full
        Supports auto-negotiation: No
        Supported FEC modes: BaseR RS
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: None

ethtool lbk0
Settings for lbk0:
	Speed: 100000Mb/s
        Duplex: Full
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX supports setting advertised link modes on physical link.
This patch adds support to derive cgx mode from ethtool
link mode and pass it to firmware to configure the same.
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CGX LMAC, the physical interface support link configuration parameters
like speed, auto negotiation, duplex  etc. Firmware saves these into
memory region shared between firmware and this driver.

This patch adds mailbox handler set_link_mode, fw_data_get to
configure and read these parameters.
Signed-off-by: NChristina Jacob <cjacob@marvell.com>
Signed-off-by: NSunil Goutham <sgoutham@marvell.com>
Signed-off-by: NHariprasad Kelam <hkelam@marvell.com>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>