New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current  FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add ethtool flow control configuration support.

Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.

Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.

Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".

This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds CM3 memory map.
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NMarcin Wojtas <mw@semihalf.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to support the possibility of per-device event channel
settings (e.g. lateeoi spurious event thresholds) add a xenbus device
pointer to struct irq_info() and modify the related event channel
binding interfaces to take the pointer to the xenbus device as a
parameter instead of the domain id of the other side.

While at it remove the stale prototype of bind_evtchn_to_irq_lateeoi().
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NBoris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: NWei Liu <wei.liu@kernel.org>
Reviewed-by: NPaul Durrant <paul@xen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of a common event for rx and tx queue the event should be
regarded to be spurious if no rx and no tx requests are pending.

Unfortunately the condition for testing that is wrong causing to
decide a event being spurious if no rx OR no tx requests are
pending.

Fix that plus using local variables for rx/tx pending indicators in
order to split function calls and if condition.

Fixes: 23025393 ("xen/netback: use lateeoi irq binding")
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NJan Beulich <jbeulich@suse.com>
Reviewed-by: NPaul Durrant <paul@xen.org>
Reviewed-by: NWei Liu <wl@xen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bond driver needs to be patched to support new ethtool speeds.
Currently it emits a single warning [1] when it encounters an unknown
speed. As evident by the two previous patches, this is not explicit
enough. Instead, promote it to an error.

[1]
bond10: (slave swp1): unknown ethtool speed (200000) for port 1 (set it to 0)

v2:
* Use pr_err_once() instead of WARN_ONCE()
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to be able to use 3ad mode with 400G devices we need to extend
the supported speeds.
Signed-off-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to be able to use 3ad mode with 200G devices we need to extend
the supported speeds.
Signed-off-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

per queue coalescing allows better and more finegrained control
over interrupt rates.
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

handle netpoll case when qede_poll is called by
netpoll layer with budget 0
Signed-off-by: NBhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: NIgor Russkikh <irusskikh@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, a random stack value is being returned because variable
_ret_ is not properly initialized. This variable is actually not
used anymore and it should be removed.

Fix this by removing all instances of variable ret and return 0.

Fixes: 64749c9c ("net: hns3: remove redundant return value of hns3_uninit_all_ring()")
Addresses-Coverity-ID: 1501700 ("Uninitialized scalar variable")
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

plat_dat is initialized by stmmac_probe_config_dt().
So, initialization is not required by priv->plat.
This removes unnecessary initialization and variables.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the operations to set desired mode and retrieve the current
mode.

This feature was tested with an IP101G.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IP101G provides three counters: RX packets, CRC errors and symbol
errors. The error counters can be configured to clear automatically on
read. Unfortunately, this isn't true for the RX packet counter. Because
of this and because the RX packet counter is more likely to overflow,
than the error counters implement only support for the error counters.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Registers >= 16 are paged. Be sure to set the page. It seems this was
working for now, because the default is correct for the registers used
in the driver at the moment. But this will also assume, nobody will
change the page select register before linux is started. The page select
register is _not_ reset with a soft reset of the PHY.

To ease the function reuse between the non-paged register space of the
IP101A and the IP101G, add noop read_page()/write_page() callbacks so
the IP101G functions can also be used for the IP101A.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This bit is reserved as 'always-write-1'. While this is not a particular
error, because we are only setting it, guard it by checking the model to
prevent errors in the future.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately, the IP101A and IP101G share the same PHY identifier.
While most of the functions are somewhat backwards compatible, there is
for example the APS_EN bit on the IP101A but on the IP101G this bit
reserved. Also, the IP101G has many more functionalities.

Deduce the model by accessing the page select register which - according
to the datasheet - is not available on the IP101A. If this register is
writable, assume we have an IP101G.

Split the combined IP101A/G driver into two separate drivers.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY core already resets the PHY before .config_init() if a
.soft_reset() op is registered. Drop the open-coded ip1xx_reset().
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't sometimes use the address operator and sometimes not. Drop it and
make the code look uniform.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the datasheet of the IP101A/G there is no revision field
and MII_PHYSID2 always reads as 0x0c54. Use PHY_ID_MATCH_EXACT() then.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simpify the initializations of the structures. There is no functional
change.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.

Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of_match_ptr() on xrs700x_mdio_dt_ids so that NULL is substituted
when CONFIG_OF isn't defined. This will prevent unnecessary use of
xrs700x_mdio_dt_ids when CONFIG_OF isn't defined.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix unused variable warning that occurs when CONFIG_OF isn't defined by
adding __maybe_unused.

>> drivers/net/dsa/xrs700x/xrs700x_i2c.c:127:34: warning: unused
variable 'xrs700x_i2c_dt_ids' [-Wunused-const-variable]
   static const struct of_device_id xrs700x_i2c_dt_ids[] = {
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit c9dca822 ("net-loopback: set lo dev initial state to UP"),
linux started automatically bringing up the loopback device of a newly
created namespace. However, an existing user script might reasonably have
the following stanza when creating a new namespace -- and in fact at least
tools/testing/selftests/net/fib_nexthops.sh in Linux's very own testsuite
does:

 # set -e
 # ip netns add foo
 # ip -netns foo addr add 127.0.0.1/8 dev lo
 # ip -netns foo link set lo up
 # set +e

This will now fail, because the kernel reasonably rejects "ip addr add" of
a duplicate address. The described change of behavior therefore constitutes
a breakage. Revert it.

Fixes: c9dca822 ("net-loopback: set lo dev initial state to UP")
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Reviewed-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.

Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.

This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this warning:
WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

stats_lock is no longer used. So remove it.
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several spinlock_t definitions without comments.
Add them.
Signed-off-by: NLijun Pan <lijunp213@gmail.com>
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>