- 14 2月, 2009 28 次提交
-
-
由 Johannes Berg 提交于
It appears that you can completely mess up mac80211 in IBSS mode by sending it a disassoc or deauth: it'll stop queues and do a lot more but not ever do anything again. Fix this by not handling all those frames in IBSS mode, Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The code beyond this point is supposed to be used for non-IBSS (managed) mode only. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Jouni Malinen <j@w1.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Just to make wext.c more self-contained. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Remove all the code from mac80211 to keep track of BSSes and use the cfg80211-provided code completely. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Add a more flexible BSS lookup function so that mac80211 or other drivers can actually use this for getting the BSS to connect to. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch introduces cfg80211_unlink_bss, a function to allow a driver to remove a BSS from the internal list and make it not show up in scan results any more -- this is to be used when the driver detects that the BSS is no longer available. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When cfg80211 users have their own allocated data in the per-BSS private data, they will need to free this when the BSS struct is destroyed. Add a free_priv method and fix one place where the BSS was kfree'd rather than released properly. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
There's no need to create a BSS struct only to pass it to ieee80211_sta_join_ibss, so refactor this function into __ieee80211_sta_join_ibss which takes all the relevant paramters, and ieee80211_sta_join_ibss which takes a BSS struct (used when joining an IBSS that already has other members). Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch adds basic scan capability to cfg80211/nl80211 and changes mac80211 to use it. The BSS list that cfg80211 maintains is made driver-accessible with a private area in each BSS struct, but mac80211 doesn't yet use it. That's another large project. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Essentially consisting of passing the sta_info pointer around, instead of repeatedly doing hash lookups. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Clean up the locking by splitting it into two functions, this will also enable further cleanups of stopping all sessions. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The sta_info pointer can very well be passed to ieee80211_sta_tear_down_BA_sessions, this will later allow us to pass it through even further. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
As far as I can tell, there are possible lockups because both the RX session_timer and TX addba_resp_timer are del_timer_sync'ed under the sta spinlock which both timer functions take. Additionally, the TX agg code seems to leak memory when TX aggregation is not disabled before the sta_info is freed. Fix this by making the free code a little smarter in the RX agg case, and actually make the sta_info_destroy code free the TX agg info in the TX agg case. We won't notify the peer, but it'll notice something is wrong anyway, and normally this only happens after we've told it in some other way we will no longer talk to it. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When disabling TX aggregation because it was rejected or from the timer (it was not accepted), there is a window where we first set the state to operation, unlock, and then undo the whole thing. Avoid that by splitting up the stop function. Also get rid of the pointless sta_info indirection in the timer. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Add documentation and move ieee80211_start_tx_ba_cb_irqsafe to right after ieee80211_start_tx_ba_cb. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Doing so would be an MLME protocol violation when the peer disabled the aggregation session. Quick driver review indicates that there are error codes passed all over the drivers but cannot ever be nonzero except in error conditions that would indicate mac80211 bugs. No real changes here, since no drivers currently can return -EBUSY. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We can only support aggregation on AP/STA right now. HT isn't defined for IBSS, WDS or MESH. In the WDS/MESH cases it's not clear what to put into the IBSS field, and we don't handle that in the code at all. Also fix the code to handle VLAN correctly. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Create two new files, agg-tx.c and agg-rx.c to make it clearer which code is common (ht.c) and which is specific (agg-*.c). Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The values are in TUs (1.024ms), not ms. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
It's a little confusing to get the BSSID outside the function and pass it in, when it's only needed for this function, so change that. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Hopefully the last required fix ... disable beaconing only on beaconing interfaces, and thus avoid calling ieee80211_if_config for purely virtual interfaces (those driver doesn't know about). Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We cannot currently hand off extra IEs to hw_scan, so reject configuring extra IEs for probe request frames when hw_scan is set. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Jouni Malinen <j@w1.fi> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Make sure nobody passes in bogus values, and translate the values (although it isn't necessary). Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Before we have a probe response frame (which is used as the beacon too) there's no need to ask drivers to beacon, they will not get a beacon anyway. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
When a directed tim bit is set, mac80211 currently disables power save ands sends a null frame to the AP. But if dynamic power save is disabled, mac80211 will not enable power save ever gain. Fix this by adding ps-poll functionality to mac80211. When a directed tim bit is set, mac80211 sends a ps-poll frame to the AP and checks for the more data bit in the returned data frames. Using ps-poll is slower than waking up with null frame, but it's saves more power in cases where the traffic is low. Userspace can control if either ps-poll or null wakeup method is used by enabling and disabling dynamic power save. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
Currently mac80211 checks for the multicast tim bit from beacons, disables power save and sends a null frame if the bit is set. This was added to support ath9k. But this is a bit controversial because the AP will send multicast frames immediately after the beacon and the time constraints are really high. Relying mac80211 to be fast enough here might not be reliable in all situations. And there's no need to send a null frame, AP will send the frames immediately after the dtim beacon no matter what. Also if dynamic power save is disabled (iwconfig wlan0 power timeout 0) currently mac80211 disables power save whenever the multicast bit is set but it's never enabled again after receiving the first multicast/broadcast frame. The current implementation is not usable on p54/stlc45xx and the easiest way to fix this is to remove the multicast tim bit check altogether. Handling multicast tim bit in host is rare, most of the designs do this in firmware/hardware, so it's better not to have it in mac80211. It's a lot better to do this in firmware/hardware, or if that's not possible it could be done in the driver. Also renamed the function to ieee80211_check_tim() to follow the style of the file. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
This issue happens only when we are associated with a 11n AP and power save is enabled. In the function 'ieee80211_master_start_xmit', ps_disable_work is queued where wake_queues is called. But before this work is executed, we check if the queues are stopped in _ieee80211_tx and return TX_AGAIN to ieee8011_tx which leads to the warning message. This patch fixes this erroneous case. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 2月, 2009 1 次提交
-
-
由 Jarek Poplawski 提交于
struct page walking should be done with proper accessor functions, not directly. With doubts from David S. Miller and Herbert Xu. Signed-off-by: NJarek Poplawski <jarkao2@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 2月, 2009 1 次提交
-
-
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 10 2月, 2009 10 次提交
-
-
由 David S. Miller 提交于
net/core/skbuff.c is a hodge-podge of symbol export placement. Some of the exports are right after the definition of the symbol being exported, others are clumped together into a big group at the end of the file. Make things consistent. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jarek Poplawski 提交于
Current "RTNETLINK answers: Invalid argument" warning, while trying to add multiq qdisc to non-multiqueue device, isn't very helpful and some of these devs can be changed btw., so let's use a better errno. With feedback from Stephen Hemminger <shemminger@vyatta.com> Reported-by: NBadalian Vyacheslav <slavon@bigtelecom.ru> Signed-off-by: NJarek Poplawski <jarkao2@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
> Kernel BUG at drivers/net/tun.c:444 > invalid opcode: 0000 [1] SMP > last sysfs file: /class/net/lo/ifindex > CPU 0 > Modules linked in: tun ipt_MASQUERADE iptable_nat ip_nat xt_state ip_conntrack > nfnetlink ipt_REJECT xt_tcpudp iptable_filter d > Pid: 6912, comm: qemu-kvm Tainted: G 2.6.18-128.el5 #1 > RIP: 0010:[<ffffffff886f57b0>] [<ffffffff886f57b0>] > :tun:tun_chr_readv+0x2b1/0x3a6 > RSP: 0018:ffff8102202c5e48 EFLAGS: 00010246 > RAX: 0000000000000000 RBX: ffff8102202c5e98 RCX: 0000000004010000 > RDX: ffff810227063680 RSI: ffff8102202c5e9e RDI: ffff8102202c5e92 > RBP: 0000000000010ff6 R08: 0000000000000000 R09: 0000000000000001 > R10: ffff8102202c5e94 R11: 0000000000000202 R12: ffff8102275357c0 > R13: ffff81022755e500 R14: 0000000000000000 R15: ffff8102202c5ef8 > FS: 00002ae4398db980(0000) GS:ffffffff803ac000(0000) knlGS:0000000000000000 > CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b > CR2: 00002ae4ab514000 CR3: 0000000221344000 CR4: 00000000000026e0 > Process qemu-kvm (pid: 6912, threadinfo ffff8102202c4000, task > ffff81022e58d820) > Stack: 00000000498735cb ffff810229d1a3c0 0000000000000000 ffff81022e58d820 > ffffffff8008a461 ffff81022755e528 ffff81022755e528 ffffffff8009f925 > 000005ea05ea0000 ffff8102209d0000 00001051143e1600 ffffffff8003c00e > Call Trace: > [<ffffffff8008a461>] default_wake_function+0x0/0xe > [<ffffffff8009f925>] enqueue_hrtimer+0x55/0x70 > [<ffffffff8003c00e>] hrtimer_start+0xbc/0xce > [<ffffffff886f58bf>] :tun:tun_chr_read+0x1a/0x1f > [<ffffffff8000b3f3>] vfs_read+0xcb/0x171 > [<ffffffff800117d4>] sys_read+0x45/0x6e > [<ffffffff8005d116>] system_call+0x7e/0x83 > > > Code: 0f 0b 68 40 62 6f 88 c2 bc 01 f6 42 0a 08 74 0c 80 4c 24 41 > RIP [<ffffffff886f57b0>] :tun:tun_chr_readv+0x2b1/0x3a6 > RSP <ffff8102202c5e48> > <0>Kernel panic - not syncing: Fatal exception This crashed when an LRO packet generated by bnx2x reached a tun device through the bridge. We're supposed to drop it at the bridge. However, because the check was placed in br_forward instead of __br_forward, it's only effective if we are sending the packet through a single port. This patch fixes it by moving the check into __br_forward. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Noriaki TAKAMIYA 提交于
When the user creates IPv6 over IPv6 tunnel, the device name created by the kernel isn't set to t->parm.name, which is referred as the result of ioctl(). Signed-off-by: NNoriaki TAKAMIYA <takamiya@po.ntts.co.jp> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Qu Haoran 提交于
When user tries to map all chunks given in argument, kernel works on a copy of the chunkmap, but at the end it doesn't check the copy, but the orginal one. Signed-off-by: NQu Haoran <haoran.qu@6wind.com> Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pablo Neira Ayuso 提交于
This patch fixes echoing if the socket that has sent the request to create/update/delete an entry is not subscribed to any multicast group. With the current code, ctnetlink would not send the echo message via unicast as nfnetlink_send() would be skip. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pablo Neira Ayuso 提交于
This patch fixes an inconsistency in the current ctnetlink code since NAT sequence adjustment bit can only be updated but not set in the conntrack entry creation. This patch is used by conntrackd to successfully recover newly created entries that represent connections with helpers and NAT payload mangling. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Leblond 提交于
This patch removes connection tracking handling for ICMPv6 messages related to Stateless Address Autoconfiguration, MLD, and MLDv2. They can not be tracked because they are massively using multicast (on pre-defined address). But they are not invalid and should not be detected as such. Signed-off-by: NEric Leblond <eric@inl.fr> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Leblond 提交于
The patch fixes a typo in the inverse mapping of Node Information request. Following draft-ietf-ipngwg-icmp-name-lookups-09, "Querier" sends a type 139 (ICMPV6_NI_QUERY) packet to "Responder" which answer with a type 140 (ICMPV6_NI_REPLY) packet. Signed-off-by: NEric Leblond <eric@inl.fr> Signed-off-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
There is no point having the bss information of currently associated AP when the AP is detected to be out of range. Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-