Base versions handle constant folding now.  For headers exposed to
userspace, we must only expose the __ prefixed versions.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use cpu_to_le32 directly as it handles constant folding now, replace direct
uses of __constant_cpu_to_{endian} as well.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When forward-porting the tun accounting patch I managed to break
the send path compltely by dropping the tun_get call.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need the udelay() for all families, including AR5416.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used for ASPM.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The test to find out if we have FAT channels do not consider that
the value of regulatory_bands for the 5000 series is larger than its
eeprom size. Using the eeprom size is strange in itself.

Use a new EEPROM_REGULATORY_BAND_NO_FAT to indicate no FAT support
and test for that explicitly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NSamuel Ortiz <samuel.ortiz@intel.com>
Tested-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch remove w/a used for development boards.
These boards are not available thus no need to keep it inside driver
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It appears that you can completely mess up mac80211 in IBSS
mode by sending it a disassoc or deauth: it'll stop queues
and do a lot more but not ever do anything again. Fix this
by not handling all those frames in IBSS mode,
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code beyond this point is supposed to be used for
non-IBSS (managed) mode only.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just to make wext.c more self-contained.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all the code from mac80211 to keep track of BSSes
and use the cfg80211-provided code completely.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a more flexible BSS lookup function so that mac80211 or
other drivers can actually use this for getting the BSS to
connect to.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch introduces cfg80211_unlink_bss, a function to
allow a driver to remove a BSS from the internal list and
make it not show up in scan results any more -- this is
to be used when the driver detects that the BSS is no
longer available.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When cfg80211 users have their own allocated data in the per-BSS
private data, they will need to free this when the BSS struct is
destroyed. Add a free_priv method and fix one place where the BSS
was kfree'd rather than released properly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's no need to create a BSS struct only to pass it to
ieee80211_sta_join_ibss, so refactor this function into
__ieee80211_sta_join_ibss which takes all the relevant
paramters, and ieee80211_sta_join_ibss which takes a BSS
struct (used when joining an IBSS that already has other
members).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Essentially consisting of passing the sta_info pointer around,
instead of repeatedly doing hash lookups.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up the locking by splitting it into two functions,
this will also enable further cleanups of stopping all
sessions.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta_info pointer can very well be passed to
ieee80211_sta_tear_down_BA_sessions, this will
later allow us to pass it through even further.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As far as I can tell, there are possible lockups because both the RX
session_timer and TX addba_resp_timer are del_timer_sync'ed under
the sta spinlock which both timer functions take. Additionally, the
TX agg code seems to leak memory when TX aggregation is not disabled
before the sta_info is freed.

Fix this by making the free code a little smarter in the RX agg case,
and actually make the sta_info_destroy code free the TX agg info in
the TX agg case. We won't notify the peer, but it'll notice something
is wrong anyway, and normally this only happens after we've told it
in some other way we will no longer talk to it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When disabling TX aggregation because it was rejected or from
the timer (it was not accepted), there is a window where we
first set the state to operation, unlock, and then undo the
whole thing. Avoid that by splitting up the stop function.
Also get rid of the pointless sta_info indirection in the timer.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add documentation and move ieee80211_start_tx_ba_cb_irqsafe to right
after ieee80211_start_tx_ba_cb.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Doing so would be an MLME protocol violation when the peer disabled
the aggregation session. Quick driver review indicates that there are
error codes passed all over the drivers but cannot ever be nonzero
except in error conditions that would indicate mac80211 bugs.

No real changes here, since no drivers currently can return -EBUSY.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can only support aggregation on AP/STA right now. HT isn't defined
for IBSS, WDS or MESH. In the WDS/MESH cases it's not clear what to
put into the IBSS field, and we don't handle that in the code at all.
Also fix the code to handle VLAN correctly.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create two new files, agg-tx.c and agg-rx.c to make it clearer
which code is common (ht.c) and which is specific (agg-*.c).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The values are in TUs (1.024ms), not ms.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's a little confusing to get the BSSID outside the function
and pass it in, when it's only needed for this function, so
change that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hopefully the last required fix ... disable beaconing
only on beaconing interfaces, and thus avoid calling
ieee80211_if_config for purely virtual interfaces
(those driver doesn't know about).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We cannot currently hand off extra IEs to hw_scan, so reject
configuring extra IEs for probe request frames when hw_scan
is set.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Jouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make sure nobody passes in bogus values, and translate the values
(although it isn't necessary).
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This makes zd1211rw honour enable_beacon, as well as fixing
a memory leak: the beacon skb is leaked when configuring it
to the hardware fails.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Before we have a probe response frame (which is used as the
beacon too) there's no need to ask drivers to beacon, they
will not get a beacon anyway.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is rather confusing to see this in the log:
[  695.606877] __ratelimit: 40 callbacks suppressed
[  700.726878] __ratelimit: 40 callbacks suppressed

without ever seeing any actual message. This is because
zd1211rw doesn't compile out the net_ratelimit() call
properly if debugging is not enabled.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a directed tim bit is set, mac80211 currently disables power save
ands sends a null frame to the AP. But if dynamic power save is
disabled, mac80211 will not enable power save ever gain. Fix this by
adding ps-poll functionality to mac80211. When a directed tim bit is
set, mac80211 sends a ps-poll frame to the AP and checks for the more
data bit in the returned data frames.

Using ps-poll is slower than waking up with null frame, but it's saves more
power in cases where the traffic is low. Userspace can control if either
ps-poll or null wakeup method is used by enabling and disabling dynamic
power save.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 checks for the multicast tim bit from beacons,
disables power save and sends a null frame if the bit is set. This was
added to support ath9k. But this is a bit controversial because the AP will
send multicast frames immediately after the beacon and the time constraints
are really high. Relying mac80211 to be fast enough here might not be
reliable in all situations. And there's no need to send a null frame, AP
will send the frames immediately after the dtim beacon no matter what.

Also if dynamic power save is disabled (iwconfig wlan0 power timeout 0)
currently mac80211 disables power save whenever the multicast bit is set
but it's never enabled again after receiving the first multicast/broadcast
frame.

The current implementation is not usable on p54/stlc45xx and the
easiest way to fix this is to remove the multicast tim bit check
altogether. Handling multicast tim bit in host is rare, most of the
designs do this in firmware/hardware, so it's better not to have it in
mac80211. It's a lot better to do this in firmware/hardware, or if
that's not possible it could be done in the driver.

Also renamed the function to ieee80211_check_tim() to follow the style
of the file.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Acked-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>