SD / MMC did not operate properly when suspend transition failed.
Because the SCC was not reset at resume, issue of the command failed.
Call the host specific reset function and reset the hardware in order to
add reset of SCC. This change also fixes tuning on some stubborn cards
on Gen2.

Based on work from Masaharu Hayakawa.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On runtime power management resume, the host clock needs to be
enabled before calling tmio_mmc_reset. If the mmc device has a power
domain entry, the host clock is enabled via genpd_runtime_resume,
running before tmio_mmc_host_runtime_resume. If the mmc device has no
power domain entry, however, genpd_runtime_resume is not called. This
patch changes tmio_mmc_host_runtime_resume to enable the host clock
before calling tmio_mmc_reset.

Based on work from Masaharu Hayakawa.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The only user was converted to fill a sbc command which is the proper
way to do it because of AutoCMD23 feature of some hosts.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NClément Péron <peron.clem@gmail.com>
Reviewed-by: NAvri Altman <avri.altman@wdc.com>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In case dmaengine_prep_slave_sg fails we need to call dma_unmap_sg.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There are two variables len within bcm2835_prepare_dma. So rename the
result of dma_map_sg to sg_len. While we are at this add a bail out to
simplify the following change.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It's better to make sure that the timeout work is really terminated
before calling mmc_request_done.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

There are two accesses on the data requests which are not protected by
the mutex. So fix this accordingly.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We need to release the slave DMA channel during driver unload.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.

A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.

Link: https://github.com/raspberrypi/linux/issues/2728Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The bcm2835 mmc host tends to lock up for unknown reason so reset it on
timeout. The upper mmc block layer tries retransimitting with single
blocks which tends to work out after a long wait.

This is better than giving up and leaving the machine broken for no
obvious reason.

Fixes: 660fc733 ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: NMichal Suchanek <msuchanek@suse.de>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Simplify things by making the i.MX SDHCI driver just use
slot GPIO with descriptors instead of passing around the global
GPIO numbers that we want to get rid of.

As it turns out, just one single board is using the platform
data to pass in GPIOs numbers for CD and WP, so we augment this
to use a machine descriptor table instead.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NDong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The power GPIO line is passed with inversion flags and all from
the platform data. Switch to using an optional GPIO descriptor and
use this to switch the power.

Augment the only boardfile to pass in the proper "power" descriptor
in the GPIO descriptor machine table instead.

As the GPIO handling is now much simpler, we can cut down on some
overhead code.

Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NPaul Burton <paul.burton@mips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Modifty the JZ4740 driver to retrieve card detect and write
protect GPIO pins from GPIO descriptors instead of hard-coded
global numbers. Augment the only board file using this in the
process and cut down on passed in platform data.

Preserve the code setting the caps2 flags for CD and WP
as active low or high since the slot GPIO code currently
ignores the gpiolib polarity inversion semantice and uses
the raw accessors to read the GPIO lines, but set the right
polarity flags in the descriptor table for jz4740.

Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NPaul Burton <paul.burton@mips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The use of string pointers in the MMC slot GPIO context is
pretty dubious, allocating some 2*len extra bytes for each
label of the ro and wp pins.

Tidy this up using kasprintf() with dynamic allocation of
labels for these strings.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On few SDHCI-MSM controllers, the host controller's clock tuning
circuit may go out of sync if controller clocks are gated which
eventually will result in data CRC, command CRC/timeout errors.
To overcome this h/w limitation, the DLL needs to be re-initialized
and restored with its old settings once clocks are ungated.
Signed-off-by: NVeerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: NEvan Green <evgreen@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Existing data command CRC error handling is non-standard and does not work
with some Intel host controllers. Specifically, the assumption that the host
controller will continue operating normally after the error interrupt,
is not valid. Change the driver to handle the error in the same manner
as a data CRC error, taking care to ensure that the data line reset is
done for single or multi-block transfers, and it is done before
unmapping DMA.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Adopt the SPDX license identifier headers to ease license compliance
management.

Cc: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Whitelist R8A77990 E3 SoC in the SDHI driver. The SDHI core
present in the SoC is an 8tap variant of the Gen3 SDHI core.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The manual does not contain information that a wait is needed in the
tuning process, this might be a leftover from early development.
Removing the wait don't have any effect on operation so delete the wait
to shorten the initialization time.
Signed-off-by: NMasaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
Signed-off-by: NTakeshi Saito <takeshi.saito.xv@renesas.com>
[Niklas: fixup commit message]
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver sets an incorrect clock and depends on the clock driver
knowledge of this incorrect setting to still set a 200Mhz SDn clock.
Instead of spreading the workaround between the two drivers the clock
driver should be made aware of the ES versions where the special clock
handling is needed no need to keep this workaround in the SDHI driver.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK() macros.

Since commit 8bd9cb51 ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The function sdhci_allocate_bounce_buffer() always return zero at
present, so there's no need to have a return value, that will also make
error path easier.

CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChunyan Zhang <zhang.chunyan@linaro.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The SDHI/MMC controller in the RZ/A2 is almost the same as R-Car gen3, but
with some minor differences.
Signed-off-by: NChris Brandt <chris.brandt@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On our AT91SAM9260 board we use the same sdio bus for wifi and for the
sd card slot. This caused the atmel-mci to give the following splat on
the serial console:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 538 at drivers/mmc/host/atmel-mci.c:859 atmci_send_command+0x24/0x44
  Modules linked in:
  CPU: 0 PID: 538 Comm: mmcqd/0 Not tainted 4.14.76 #14
  Hardware name: Atmel AT91SAM9
  [<c000fccc>] (unwind_backtrace) from [<c000d3dc>] (show_stack+0x10/0x14)
  [<c000d3dc>] (show_stack) from [<c0017644>] (__warn+0xd8/0xf4)
  [<c0017644>] (__warn) from [<c0017704>] (warn_slowpath_null+0x1c/0x24)
  [<c0017704>] (warn_slowpath_null) from [<c033bb9c>] (atmci_send_command+0x24/0x44)
  [<c033bb9c>] (atmci_send_command) from [<c033e984>] (atmci_start_request+0x1f4/0x2dc)
  [<c033e984>] (atmci_start_request) from [<c033f3b4>] (atmci_request+0xf0/0x164)
  [<c033f3b4>] (atmci_request) from [<c0327108>] (mmc_start_request+0x280/0x2d0)
  [<c0327108>] (mmc_start_request) from [<c032800c>] (mmc_start_areq+0x230/0x330)
  [<c032800c>] (mmc_start_areq) from [<c03366f8>] (mmc_blk_issue_rw_rq+0xc4/0x310)
  [<c03366f8>] (mmc_blk_issue_rw_rq) from [<c03372c4>] (mmc_blk_issue_rq+0x118/0x5ac)
  [<c03372c4>] (mmc_blk_issue_rq) from [<c033781c>] (mmc_queue_thread+0xc4/0x118)
  [<c033781c>] (mmc_queue_thread) from [<c002daf8>] (kthread+0x100/0x118)
  [<c002daf8>] (kthread) from [<c000a580>] (ret_from_fork+0x14/0x34)
  ---[ end trace 594371ddfa284bd6 ]---

This is:
  WARN_ON(host->cmd);

This was fixed on our board by letting atmci_request_end determine what
state we are in. Instead of unconditionally setting it to STATE_IDLE on
STATE_END_REQUEST.
Signed-off-by: NJonas Danielsson <jonas@orbital-systems.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This commit removes the unnecessary of-node check since the
dw_mci_bluefield_match[] structure has only one entry.
Signed-off-by: NLiming Sun <lsun@mellanox.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

With the new validation code, a malicious user-space app could
potentially submit command streams with enough buffer-object and resource
references in them to have the resulting allocated validion nodes and
relocations make the kernel run out of GFP_KERNEL memory.

Protect from this by having the validation code reserve TTM graphics
memory when allocating.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NDeepak Rawat <drawat@vmware.com>
---
v2: Removed leftover debug printouts

Since this is not needed any more on the latest SMC firmware.
Signed-off-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

When support for bonding of RoCE devices was added, there was
necessarily a link between the RoCE device and the paired netdevice that
was part of the bond.  If you remove the mlx4_en module, that paired
association is broken (the RoCE device is still present but the paired
netdevice has been released).  We need to account for this in
is_upper_ndev_bond_master_filter() and filter out those links with a
broken pairing or else we later oops in netdev_next_upper_dev_rcu().

Fixes: 408f1242 ("IB/core: Delete lower netdevice default GID entries in bonding scenario")
Signed-off-by: NMark Zhang <markz@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Decoupled version bump from commit f6c36758 ("dm thin: send event
about thin-pool state change _after_ making it") because version bumps
just create conflicts when backporting to the stable trees.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The return statement is redundant as there is a return statement
immediately before it so we have dead code that can be removed.
Also remove the unused declaration of ret.

Detected by CoverityScan, CID#1473793 ("Structurally dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>

Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.

Fixes: 7dd4f672 ("drm/i915: Async GPU relocation processing")
References: 7fa28e14 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
(cherry picked from commit a889580c)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.

For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.

v2: Check that we allocated a large enough scratch for I830 w/a

Fixes: 06e562e7f515 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
(cherry picked from commit 51797499)
[Joonas: Use new function in gen9_init_indirectctx_bb too]
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Braswell is really picky about having our writes posted to memory before
we execute or else the GPU may see stale values. A wmb() is insufficient
as it only ensures the writes are visible to other cores, we need a full
mb() to ensure the writes are in memory and visible to the GPU.

The most frequent failure in flushing before execution is that we see
stale PTE values and execute the wrong pages.

References: 987abd5c ("drm/i915/execlists: Force write serialisation into context image vs execution")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206084431.9805-3-chris@chris-wilson.co.uk
(cherry picked from commit 490b8c65)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Noticed this while working on redoing the reference counting scheme in
the DP MST helpers. Nouveau doesn't attempt to call
drm_dp_mst_topology_mgr_destroy() at all, which leaves it leaking all of
the resources for drm_dp_mst_topology_mgr and it's children mstbs+ports.

Fixes: f479c0ba ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Should hopefully fix a regression some people have been seeing since EVO
push buffers were moved to VRAM by default on Pascal GPUs.

Fixes: d00ddd9d ("drm/nouveau/kms/nv50-: allocate push buffers in vidmem on pascal")
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 4.19+

Sending a DM event before a thin-pool state change is about to happen is
a bug.  It wasn't realized until it became clear that userspace response
to the event raced with the actual state change that the event was
meant to notify about.

Fix this by first updating internal thin-pool state to reflect what the
DM event is being issued about.  This fixes a long-standing racey/buggy
userspace device-mapper-test-suite 'resize_io' test that would get an
event but not find the state it was looking for -- so it would just go
on to hang because no other events caused the test to reevaluate the
thin-pool's state.

Cc: stable@vger.kernel.org
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

If CS is submitted using guilty ctx, we terminate amdgpu_cs_parser_init
before locking ctx->lock, latter in amdgpu_cs_parser_fini we still are
trying to release the lock just becase parser->ctx != NULL.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 7f3ef5de.

It causes new warnings [1] on shutdown when running the Google Kevin or
Scarlet (RK3399) boards under Chrome OS. Presumably our usage of DRM is
different than what Marc and Heiko test.

We're looking at a different approach (e.g., [2]) to replace this, but
IMO the revert should be taken first, as it already propagated to
-stable.

[1] Report here:
http://lkml.kernel.org/lkml/20181205030127.GA200921@google.com

WARNING: CPU: 4 PID: 2035 at drivers/gpu/drm/drm_mode_config.c:477 drm_mode_config_cleanup+0x1c4/0x294
...
 Call trace:
  drm_mode_config_cleanup+0x1c4/0x294
  rockchip_drm_unbind+0x4c/0x8c
  component_master_del+0x88/0xb8
  rockchip_drm_platform_remove+0x2c/0x44
  rockchip_drm_platform_shutdown+0x20/0x2c
  platform_drv_shutdown+0x2c/0x38
  device_shutdown+0x164/0x1b8
  kernel_restart_prepare+0x40/0x48
  kernel_restart+0x20/0x68
...
 Memory manager not clean during takedown.
 WARNING: CPU: 4 PID: 2035 at drivers/gpu/drm/drm_mm.c:950 drm_mm_takedown+0x34/0x44
...
  drm_mm_takedown+0x34/0x44
  rockchip_drm_unbind+0x64/0x8c
  component_master_del+0x88/0xb8
  rockchip_drm_platform_remove+0x2c/0x44
  rockchip_drm_platform_shutdown+0x20/0x2c
  platform_drv_shutdown+0x2c/0x38
  device_shutdown+0x164/0x1b8
  kernel_restart_prepare+0x40/0x48
  kernel_restart+0x20/0x68
...

[2] https://patchwork.kernel.org/patch/10556151/
    https://www.spinics.net/lists/linux-rockchip/msg21342.html
    [PATCH] drm/rockchip: shutdown drm subsystem on shutdown

Fixes: 7f3ef5de ("drm/rockchip: Allow driver to be shutdown on reboot/kexec")
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Vicente Bergas <vicencb@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: stable@vger.kernel.org
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205181657.177703-1-briannorris@chromium.org