In order to allow querying of the VID for which a RIF was created, add
a new function that returns a FID for a given RIF.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to guard against removal of a PVID for which a FID was
allocated, spectrum_switchdev needs to first determine whether there is
a RIF associated with a given bridge. To that end, publish a preexisting
function mlxsw_sp_rif_find_by_dev().
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For bridge netdevices, instead of assuming that the router traffic is on
VLAN 1, look at the bridge PVID.

This patch assumes that the PVID doesn't change after the router
interface is created (i.e. after the IP address is assigned).
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the follow-up patch, mlxsw_sp_rif_vlan_fid_get() will be changed in a
way that could fail. Give that function a possibility to explain the
failure through extack.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.

Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.

This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: NMark Brown <broonie@kernel.org>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switchdev notifications for addition of SWITCHDEV_OBJ_ID_PORT_VLAN are
distributed not only on clean addition, but also when flags on an
existing VLAN are changed. mlxsw_sp_bridge_port_vlan_add() calls
mlxsw_sp_port_vlan_get() to get at the port_vlan in question, which
implicitly references the object. This then leads to discrepancies in
reference counting when the VLAN is removed. spectrum.c warns about the
problem when the module is removed:

[13578.493090] WARNING: CPU: 0 PID: 2454 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2973 mlxsw_sp_port_remove+0xfd/0x110 [mlxsw_spectrum]
[...]
[13578.627106] Call Trace:
[13578.629617]  mlxsw_sp_fini+0x2a/0xe0 [mlxsw_spectrum]
[13578.634748]  mlxsw_core_bus_device_unregister+0x3e/0x130 [mlxsw_core]
[13578.641290]  mlxsw_pci_remove+0x13/0x40 [mlxsw_pci]
[13578.646238]  pci_device_remove+0x31/0xb0
[13578.650244]  device_release_driver_internal+0x14f/0x220
[13578.655562]  driver_detach+0x32/0x70
[13578.659183]  bus_remove_driver+0x47/0xa0
[13578.663134]  pci_unregister_driver+0x1e/0x80
[13578.667486]  mlxsw_sp_module_exit+0xc/0x3fa [mlxsw_spectrum]
[13578.673207]  __x64_sys_delete_module+0x13b/0x1e0
[13578.677888]  ? exit_to_usermode_loop+0x78/0x80
[13578.682374]  do_syscall_64+0x39/0xe0
[13578.685976]  entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fix by putting the port_vlan when mlxsw_sp_port_vlan_bridge_join()
determines it's a flag-only change.

Fixes: b3529af6 ("spectrum: Reference count VLAN entries")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f34436a4 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route replace logic so that the
first matching route (i.e., same metric) is replaced.

Have mlxsw replace the first matching route as well.

Fixes: f34436a4 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f34436a4 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route append logic so that
dev-only routes can be appended and not only gatewayed routes.

Align mlxsw with the new behaviour.

Fixes: f34436a4 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The kzalloc() function has a 2-factor argument form, kcalloc(). This
patch replaces cases of:

        kzalloc(a * b, gfp)

with:
        kcalloc(a * b, gfp)

as well as handling cases of:

        kzalloc(a * b * c, gfp)

with:

        kzalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kzalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kzalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kzalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kzalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kzalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kzalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kzalloc
+ kcalloc
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kzalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kzalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kzalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kzalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kzalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kzalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kzalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kzalloc(sizeof(THING) * C2, ...)
|
  kzalloc(sizeof(TYPE) * C2, ...)
|
  kzalloc(C1 * C2 * C3, ...)
|
  kzalloc(C1 * C2, ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kzalloc
+ kcalloc
  (
-	E1 * E2
+	E1, E2
  , ...)
)
Signed-off-by: NKees Cook <keescook@chromium.org>

Return messages in extack for port split/unsplit errors. e.g.,
    $ devlink port split swp1s1 count 4
    Error: mlxsw_spectrum: Port cannot be split further.
    devlink answers: Invalid argument

    $ devlink port unsplit swp4
    Error: mlxsw_spectrum: Port was not split.
    devlink answers: Invalid argument
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add extack argument to reload, port_split and port_unsplit operations.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When offloading mirroring to gretap or ip6gretap netdevices, an 802.1q
bridge is one of the soft devices permissible in the underlay when
resolving the packet path. After the packet path is resolved to a
particular bridge egress device, flags on packet VLAN determine whether
the egressed packet should be tagged.

The current logic however only ever sets the VLAN tag, never suppresses
it. Thus if there's a VLAN netdevice above the bridge that determines
the packet VLAN, that VLAN is never unset, and mirroring is configured
with VLAN tagging.

Fix by setting the packet VLAN on both branches: set to zero (for unset)
when BRIDGE_VLAN_INFO_UNTAGGED, copy the resolved VLAN (e.g. from bridge
PVID) otherwise.

Fixes: 946a11e7 ("mlxsw: spectrum_span: Allow bridge for gretap mirror")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN deletion notifications are emitted before the relevant change is
projected to bridge configuration. Thus, like with VLAN addition,
schedule SPAN respin for later.

Fixes: c520bc69 ("mlxsw: Respin SPAN on switchdev events")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there's no special support for the bridge events, the driver
returns -EOPNOTSUPP, and thus the commit never happens. Therefore
schedule respin during the prepare stage: there's no real difference one
way or another.

This fixes the problem that mirror-to-gretap offload wouldn't adapt to
changes in bridge vlan configuration right away and another notification
would have to arrive for mlxsw to catch up.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.

Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far, the PCI BAR0 register is used for triggering FW reset. However,
that is a legacy attitude and it is recommended to use MRSR to perform
reset instead. So do that. Move the reset into init() function as
the cmd interface needs to be used. With that, IRQ initialization needs
to be moved as well. As a side effect, the reset move simplifies
the devlink reload flow.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an exception in command interface processing in case the MRSR
register is written to. The register triggers FW reset and during the
reset FW returns an error. So handle this by ignoring this error while
writing to MRSR register.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN 1 is internally used for untagged traffic. Prevent creation of
explicit netdevice for that VLAN, because that currently isn't supported
and leads to the NULL pointer dereference cited below.

Fix by preventing creation of VLAN devices with VID of 1 over mlxsw
devices or LAG devices that involve mlxsw devices.

[  327.175816] ================================================================================
[  327.184544] UBSAN: Undefined behaviour in drivers/net/ethernet/mellanox/mlxsw/spectrum_fid.c:200:12
[  327.193667] member access within null pointer of type 'const struct mlxsw_sp_fid'
[  327.201226] CPU: 0 PID: 8983 Comm: ip Not tainted 4.17.0-rc4-petrm_net_ip6gre_headroom-custom-140 #11
[  327.210496] Hardware name: Mellanox Technologies Ltd. "MSN2410-CB2F"/"SA000874", BIOS 4.6.5 03/08/2016
[  327.219872] Call Trace:
[  327.222384]  dump_stack+0xc3/0x12b
[  327.234007]  ubsan_epilogue+0x9/0x49
[  327.237638]  ubsan_type_mismatch_common+0x1f9/0x2d0
[  327.255769]  __ubsan_handle_type_mismatch+0x90/0xa7
[  327.264716]  mlxsw_sp_fid_type+0x35/0x50 [mlxsw_spectrum]
[  327.270255]  mlxsw_sp_port_vlan_router_leave+0x46/0xc0 [mlxsw_spectrum]
[  327.277019]  mlxsw_sp_inetaddr_port_vlan_event+0xe1/0x340 [mlxsw_spectrum]
[  327.315031]  mlxsw_sp_netdevice_vrf_event+0xa8/0x100 [mlxsw_spectrum]
[  327.321626]  mlxsw_sp_netdevice_event+0x276/0x430 [mlxsw_spectrum]
[  327.367863]  notifier_call_chain+0x4c/0x150
[  327.372128]  __netdev_upper_dev_link+0x1b3/0x260
[  327.399450]  vrf_add_slave+0xce/0x170 [vrf]
[  327.403703]  do_setlink+0x658/0x1d70
[  327.508998]  rtnl_newlink+0x908/0xf20
[  327.559128]  rtnetlink_rcv_msg+0x50c/0x720
[  327.571720]  netlink_rcv_skb+0x16a/0x1f0
[  327.583450]  netlink_unicast+0x2ca/0x3e0
[  327.599305]  netlink_sendmsg+0x3e2/0x7f0
[  327.616655]  sock_sendmsg+0x76/0xc0
[  327.620207]  ___sys_sendmsg+0x494/0x5d0
[  327.666117]  __sys_sendmsg+0xc2/0x130
[  327.690953]  do_syscall_64+0x66/0x370
[  327.694677]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  327.699782] RIP: 0033:0x7f4c2f3f8037
[  327.703393] RSP: 002b:00007ffe8c389708 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  327.711035] RAX: ffffffffffffffda RBX: 000000005b03f53e RCX: 00007f4c2f3f8037
[  327.718229] RDX: 0000000000000000 RSI: 00007ffe8c389760 RDI: 0000000000000003
[  327.725431] RBP: 00007ffe8c389760 R08: 0000000000000000 R09: 00007f4c2f443630
[  327.732632] R10: 00000000000005eb R11: 0000000000000246 R12: 0000000000000000
[  327.739833] R13: 00000000006774e0 R14: 00007ffe8c3897e8 R15: 0000000000000000
[  327.747096] ================================================================================

Fixes: 9589a7b5 ("mlxsw: spectrum: Handle VLAN devices linking / unlinking")
Suggested-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since devlink knows the info needed to generate the physical port name
in a generic way for all devlink users, use the helper to do the job.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Devlink ports can have specific flavour according to the purpose of use.
This patch extend attrs_set so the driver can say which flavour port
has. Initial flavours are:
physical, cpu, dsa
User can query this to see right away what is the purpose of each port.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When resolving a path that the packet will take after being encapsulated
in mirror-to-gretap scenarios, one of the devices en route could be a
LAG. In that case, mirror to first up slave that corresponds to a front
panel port.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENOENT is suitable when an item is looked for in a collection and can't
be found. The failure here is actually a depletion of a resource, where
ENOBUFS is the more fitting error code.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling the variable l3edev was relevant when neighbor lookup was the
last stage in the simulated pipeline. Now that mlxsw handles bridges and
vlan devices as well, calling it "L3" is a misnomer.

Thus in mlxsw_sp_span_dmac(), rename to "dev", because that function is
just a service routine where the distinction between tunnel and egress
device isn't necessary.

In mlxsw_sp_span_entry_tunnel_parms_common(), rename to "edev" to
emphasize that the routine traces packet egress.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resources are not freed in the reverse order of the allocation.
Labels are also mixed-up.

Fix it and reorder code and labels in the error handling path of
'mlxsw_core_bus_device_register()'

Fixes: ef3116e5 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When mirroring to a gretap or ip6gretap device, allow the underlay
packet path to include VLAN devices. The following configurations are
supported in underlay:

- vlan over phys
- vlan-unaware bridge where the egress device is vlan over phys
- vlan over vlan-aware bridge where the egress device is phys
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload "tc action mirred mirror" to a device that is a vlan device on
top of a front-panel port device. The hardware encapsulates the mirrored
packets in a VLAN tag. That includes the case that the mirrored traffic
is already VLAN-tagged--in that case the monitor traffic will be
double-tagged, just like in the software path.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MLXSW_REG_MPAT_SPAN_TYPE_REMOTE_ETH to support VLAN-encapsulated
port mirroring.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.

To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check number of CQEs for CQE version 2 reported by QUERY_AQ_CAP command.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use previously added resources to query FW support for multiple versions
of CQEs. Use the biggest version supported. For SDQs, it has no sense to
use version 2 as it does not introduce any new features, but it is
twice the size of CQE version 1.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce definitions of fields in CQE version 1 and 2. Also, introduce
common helpers that would call appropriate version-specific helpers
according to the version enum passed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add resources that FW uses to report supported CQE versions.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.

However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 9776d325 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.

Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.

Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.

Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When handling mirroring to a gretap or ip6gretap netdevice in mlxsw, the
underlay address (i.e. the remote address of the tunnel) may be routed
to a bridge.

In that case, look up the resolved neighbor Ethernet address in that
bridge's FDB. Then configure the offload to direct the mirrored traffic
to that port, possibly with tagging.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes to switchdev artifact can make a SPAN entry offloadable or
unoffloadable. To that end:

- Listen to SWITCHDEV_FDB_*_TO_BRIDGE notifications in addition to
  the *_TO_DEVICE ones, to catch whatever activity is sent to the
  bridge (likely by mlxsw itself).

  On each FDB notification, respin SPAN to reconcile it with the FDB
  changes.

- Also respin on switchdev port attribute changes (which currently
  covers changes to STP state of ports) and port object additions and
  removals.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since switchdev events can trigger SPAN respin, it is necessary that the
data structures are available. Register SPAN first, with a commentary on
what the dependencies are.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>