Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 01 9月, 2016 32 次提交
    • R
      net: asix: see 802.3 spec for phy reset · a243c2ef
      由 Robert Foss 提交于 
      From: Grant Grundler <grundler@chromium.org>

https://lkml.org/lkml/2014/11/11/947

Ben Hutchings is correct. IEEE 802.3 spec section "22.2.4.1.1 Reset" requires
up to 500ms delay. Mitigate the "max" delay by polling the phy until BCM_RESET
bit is clear.
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NRobert Foss <robert.foss@collabora.com>
Tested-by: NRobert Foss <robert.foss@collabora.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a243c2ef
    • R
      net: asix: Fix AX88772x resume failures · 4c1442aa
      由 Robert Foss 提交于 
      From: Allan Chou <allan@asix.com.tw>

The change fixes AX88772x resume failure by
- Restore incorrect AX88772A PHY registers when resetting
- Need to stop MAC operation when suspending
- Need to restart MII when restoring PHY
Signed-off-by: NAllan Chou <allan@asix.com.tw>
Signed-off-by: NRobert Foss <robert.foss@collabora.com>
Tested-by: NRobert Foss <robert.foss@collabora.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4c1442aa
    • R
      net: asix: Avoid looping when the device is disconnected · 8a46f665
      由 Robert Foss 提交于 
      From: Vincent Palatin <vpalatin@chromium.org>

Check the answers from the USB stack and avoid re-sending multiple times
the request if the device has disappeared.
Signed-off-by: NVincent Palatin <vpalatin@chromium.org>
Signed-off-by: NRobert Foss <robert.foss@collabora.com>
Tested-by: NRobert Foss <robert.foss@collabora.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8a46f665
    • R
      net: asix: Add in_pm parameter · d9fe64e5
      由 Robert Foss 提交于 
      From: Freddy Xin <freddy@asix.com.tw>

In order to R/W registers in suspend/resume functions, in_pm flags are
added to some functions to determine whether the nopm version of usb
functions is called.

Save BMCR and ANAR PHY registers in suspend function and restore them
in resume function.

Reset HW in resume function to ensure the PHY works correctly.
Signed-off-by: NFreddy Xin <freddy@asix.com.tw>
Signed-off-by: NRobert Foss <robert.foss@collabora.com>
Tested-by: NRobert Foss <robert.foss@collabora.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d9fe64e5
    • J
      net: axienet: constify ethtool_ops structures · c7735f1b
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c7735f1b
    • J
      r8152: constify ethtool_ops structures · 407a471d
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      407a471d
    • J
      net: mediatek: constify ethtool_ops structures · 6a38cb15
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6a38cb15
    • D
      Merge branch 'ppp-recursion' · 127661a4
      由 David S. Miller 提交于 
      Guillaume Nault says:

====================
ppp: fix deadlock upon recursive xmit

This series fixes the issue reported by Feng where packets looping
through a ppp device makes the module deadlock:
https://marc.info/?l=linux-netdev&m=147134567319038&w=2

The problem can occur on virtual interfaces (e.g. PPP over L2TP, or
PPPoE on vxlan devices), when a PPP packet is routed back to the PPP
interface.

PPP's xmit path isn't reentrant, so patch #1 uses a per-cpu variable
to detect and break recursion. Patch #2 sets the NETIF_F_LLTX flag to
avoid lock inversion issues between ppp and txqueue locks.

There are multiple entry points to the PPP xmit path. This series has
been tested with lockdep and should address recursion issues no matter
how the packet entered the path.

A similar issue in L2TP is not covered by this series:
l2tp_xmit_skb() also isn't reentrant, and it can be called as part of
PPP's xmit path (pppol2tp_xmit()), or directly from the L2TP socket
(l2tp_ppp_sendmsg()). If a packet is sent by l2tp_ppp_sendmsg() and
routed to the parent PPP interface, then it's going to hit
l2tp_xmit_skb() again.

Breaking recursion as done in ppp_generic is not enough, because we'd
still have a lock inversion issue (locking in l2tp_xmit_skb() can
happen before or after locking in ppp_generic). The best approach would
be to use the ip_tunnel functions and remove the socket locking in
l2tp_xmit_skb(). But that'd be something for net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      127661a4
    • G
      ppp: declare PPP devices as LLTX · 07712770
      由 Guillaume Nault 提交于 
      ppp_xmit_process() already locks the xmit path. If HARD_TX_LOCK() tries
to hold the _xmit_lock we can get lock inversion.

[  973.726130] ======================================================
[  973.727311] [ INFO: possible circular locking dependency detected ]
[  973.728546] 4.8.0-rc2 #1 Tainted: G           O
[  973.728986] -------------------------------------------------------
[  973.728986] accel-pppd/1806 is trying to acquire lock:
[  973.728986]  (&qdisc_xmit_lock_key){+.-...}, at: [<ffffffff8146f6fe>] sch_direct_xmit+0x8d/0x221
[  973.728986]
[  973.728986] but task is already holding lock:
[  973.728986]  (l2tp_sock){+.-...}, at: [<ffffffffa0202c4a>] l2tp_xmit_skb+0x1e8/0x5d7 [l2tp_core]
[  973.728986]
[  973.728986] which lock already depends on the new lock.
[  973.728986]
[  973.728986]
[  973.728986] the existing dependency chain (in reverse order) is:
[  973.728986]
-> #3 (l2tp_sock){+.-...}:
[  973.728986]        [<ffffffff810b3130>] lock_acquire+0x150/0x217
[  973.728986]        [<ffffffff815752f4>] _raw_spin_lock+0x2d/0x3c
[  973.728986]        [<ffffffffa0202c4a>] l2tp_xmit_skb+0x1e8/0x5d7 [l2tp_core]
[  973.728986]        [<ffffffffa01b2466>] pppol2tp_xmit+0x1f2/0x25e [l2tp_ppp]
[  973.728986]        [<ffffffffa0184f59>] ppp_channel_push+0xb5/0x14a [ppp_generic]
[  973.728986]        [<ffffffffa01853ed>] ppp_write+0x104/0x11c [ppp_generic]
[  973.728986]        [<ffffffff811b2ec6>] __vfs_write+0x56/0x120
[  973.728986]        [<ffffffff811b3f4c>] vfs_write+0xbd/0x11b
[  973.728986]        [<ffffffff811b4cb2>] SyS_write+0x5e/0x96
[  973.728986]        [<ffffffff81575ba5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[  973.728986]
-> #2 (&(&pch->downl)->rlock){+.-...}:
[  973.728986]        [<ffffffff810b3130>] lock_acquire+0x150/0x217
[  973.728986]        [<ffffffff81575334>] _raw_spin_lock_bh+0x31/0x40
[  973.728986]        [<ffffffffa01808e2>] ppp_push+0xa7/0x82d [ppp_generic]
[  973.728986]        [<ffffffffa0184675>] __ppp_xmit_process+0x48/0x877 [ppp_generic]
[  973.728986]        [<ffffffffa018505b>] ppp_xmit_process+0x4b/0xaf [ppp_generic]
[  973.728986]        [<ffffffffa01853f7>] ppp_write+0x10e/0x11c [ppp_generic]
[  973.728986]        [<ffffffff811b2ec6>] __vfs_write+0x56/0x120
[  973.728986]        [<ffffffff811b3f4c>] vfs_write+0xbd/0x11b
[  973.728986]        [<ffffffff811b4cb2>] SyS_write+0x5e/0x96
[  973.728986]        [<ffffffff81575ba5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[  973.728986]
-> #1 (&(&ppp->wlock)->rlock){+.-...}:
[  973.728986]        [<ffffffff810b3130>] lock_acquire+0x150/0x217
[  973.728986]        [<ffffffff81575334>] _raw_spin_lock_bh+0x31/0x40
[  973.728986]        [<ffffffffa0184654>] __ppp_xmit_process+0x27/0x877 [ppp_generic]
[  973.728986]        [<ffffffffa018505b>] ppp_xmit_process+0x4b/0xaf [ppp_generic]
[  973.728986]        [<ffffffffa01852da>] ppp_start_xmit+0x21b/0x22a [ppp_generic]
[  973.728986]        [<ffffffff8143f767>] dev_hard_start_xmit+0x1a9/0x43d
[  973.728986]        [<ffffffff8146f747>] sch_direct_xmit+0xd6/0x221
[  973.728986]        [<ffffffff814401e4>] __dev_queue_xmit+0x62a/0x912
[  973.728986]        [<ffffffff814404d7>] dev_queue_xmit+0xb/0xd
[  973.728986]        [<ffffffff81449978>] neigh_direct_output+0xc/0xe
[  973.728986]        [<ffffffff8150e62b>] ip6_finish_output2+0x5a9/0x623
[  973.728986]        [<ffffffff81512128>] ip6_output+0x15e/0x16a
[  973.728986]        [<ffffffff8153ef86>] dst_output+0x76/0x7f
[  973.728986]        [<ffffffff8153f737>] mld_sendpack+0x335/0x404
[  973.728986]        [<ffffffff81541c61>] mld_send_initial_cr.part.21+0x99/0xa2
[  973.728986]        [<ffffffff8154441d>] ipv6_mc_dad_complete+0x42/0x71
[  973.728986]        [<ffffffff8151c4bd>] addrconf_dad_completed+0x1cf/0x2ea
[  973.728986]        [<ffffffff8151e4fa>] addrconf_dad_work+0x453/0x520
[  973.728986]        [<ffffffff8107a393>] process_one_work+0x365/0x6f0
[  973.728986]        [<ffffffff8107aecd>] worker_thread+0x2de/0x421
[  973.728986]        [<ffffffff810816fb>] kthread+0x121/0x130
[  973.728986]        [<ffffffff81575dbf>] ret_from_fork+0x1f/0x40
[  973.728986]
-> #0 (&qdisc_xmit_lock_key){+.-...}:
[  973.728986]        [<ffffffff810b28d6>] __lock_acquire+0x1118/0x1483
[  973.728986]        [<ffffffff810b3130>] lock_acquire+0x150/0x217
[  973.728986]        [<ffffffff815752f4>] _raw_spin_lock+0x2d/0x3c
[  973.728986]        [<ffffffff8146f6fe>] sch_direct_xmit+0x8d/0x221
[  973.728986]        [<ffffffff814401e4>] __dev_queue_xmit+0x62a/0x912
[  973.728986]        [<ffffffff814404d7>] dev_queue_xmit+0xb/0xd
[  973.728986]        [<ffffffff81449978>] neigh_direct_output+0xc/0xe
[  973.728986]        [<ffffffff81487811>] ip_finish_output2+0x5db/0x609
[  973.728986]        [<ffffffff81489590>] ip_finish_output+0x152/0x15e
[  973.728986]        [<ffffffff8148a0d4>] ip_output+0x8c/0x96
[  973.728986]        [<ffffffff81489652>] ip_local_out+0x41/0x4a
[  973.728986]        [<ffffffff81489e7d>] ip_queue_xmit+0x5a5/0x609
[  973.728986]        [<ffffffffa0202fe4>] l2tp_xmit_skb+0x582/0x5d7 [l2tp_core]
[  973.728986]        [<ffffffffa01b2466>] pppol2tp_xmit+0x1f2/0x25e [l2tp_ppp]
[  973.728986]        [<ffffffffa0184f59>] ppp_channel_push+0xb5/0x14a [ppp_generic]
[  973.728986]        [<ffffffffa01853ed>] ppp_write+0x104/0x11c [ppp_generic]
[  973.728986]        [<ffffffff811b2ec6>] __vfs_write+0x56/0x120
[  973.728986]        [<ffffffff811b3f4c>] vfs_write+0xbd/0x11b
[  973.728986]        [<ffffffff811b4cb2>] SyS_write+0x5e/0x96
[  973.728986]        [<ffffffff81575ba5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[  973.728986]
[  973.728986] other info that might help us debug this:
[  973.728986]
[  973.728986] Chain exists of:
  &qdisc_xmit_lock_key --> &(&pch->downl)->rlock --> l2tp_sock

[  973.728986]  Possible unsafe locking scenario:
[  973.728986]
[  973.728986]        CPU0                    CPU1
[  973.728986]        ----                    ----
[  973.728986]   lock(l2tp_sock);
[  973.728986]                                lock(&(&pch->downl)->rlock);
[  973.728986]                                lock(l2tp_sock);
[  973.728986]   lock(&qdisc_xmit_lock_key);
[  973.728986]
[  973.728986]  *** DEADLOCK ***
[  973.728986]
[  973.728986] 6 locks held by accel-pppd/1806:
[  973.728986]  #0:  (&(&pch->downl)->rlock){+.-...}, at: [<ffffffffa0184efa>] ppp_channel_push+0x56/0x14a [ppp_generic]
[  973.728986]  #1:  (l2tp_sock){+.-...}, at: [<ffffffffa0202c4a>] l2tp_xmit_skb+0x1e8/0x5d7 [l2tp_core]
[  973.728986]  #2:  (rcu_read_lock){......}, at: [<ffffffff81486981>] rcu_lock_acquire+0x0/0x20
[  973.728986]  #3:  (rcu_read_lock_bh){......}, at: [<ffffffff81486981>] rcu_lock_acquire+0x0/0x20
[  973.728986]  #4:  (rcu_read_lock_bh){......}, at: [<ffffffff814340e3>] rcu_lock_acquire+0x0/0x20
[  973.728986]  #5:  (dev->qdisc_running_key ?: &qdisc_running_key#2){+.....}, at: [<ffffffff8144011e>] __dev_queue_xmit+0x564/0x912
[  973.728986]
[  973.728986] stack backtrace:
[  973.728986] CPU: 2 PID: 1806 Comm: accel-pppd Tainted: G           O    4.8.0-rc2 #1
[  973.728986] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[  973.728986]  ffff7fffffffffff ffff88003436f850 ffffffff812a20f4 ffffffff82156e30
[  973.728986]  ffffffff82156920 ffff88003436f890 ffffffff8115c759 ffff88003344ae00
[  973.728986]  ffff88003344b5c0 0000000000000002 0000000000000006 ffff88003344b5e8
[  973.728986] Call Trace:
[  973.728986]  [<ffffffff812a20f4>] dump_stack+0x67/0x90
[  973.728986]  [<ffffffff8115c759>] print_circular_bug+0x22e/0x23c
[  973.728986]  [<ffffffff810b28d6>] __lock_acquire+0x1118/0x1483
[  973.728986]  [<ffffffff810b3130>] lock_acquire+0x150/0x217
[  973.728986]  [<ffffffff810b3130>] ? lock_acquire+0x150/0x217
[  973.728986]  [<ffffffff8146f6fe>] ? sch_direct_xmit+0x8d/0x221
[  973.728986]  [<ffffffff815752f4>] _raw_spin_lock+0x2d/0x3c
[  973.728986]  [<ffffffff8146f6fe>] ? sch_direct_xmit+0x8d/0x221
[  973.728986]  [<ffffffff8146f6fe>] sch_direct_xmit+0x8d/0x221
[  973.728986]  [<ffffffff814401e4>] __dev_queue_xmit+0x62a/0x912
[  973.728986]  [<ffffffff814404d7>] dev_queue_xmit+0xb/0xd
[  973.728986]  [<ffffffff81449978>] neigh_direct_output+0xc/0xe
[  973.728986]  [<ffffffff81487811>] ip_finish_output2+0x5db/0x609
[  973.728986]  [<ffffffff81486853>] ? dst_mtu+0x29/0x2e
[  973.728986]  [<ffffffff81489590>] ip_finish_output+0x152/0x15e
[  973.728986]  [<ffffffff8148a0bc>] ? ip_output+0x74/0x96
[  973.728986]  [<ffffffff8148a0d4>] ip_output+0x8c/0x96
[  973.728986]  [<ffffffff81489652>] ip_local_out+0x41/0x4a
[  973.728986]  [<ffffffff81489e7d>] ip_queue_xmit+0x5a5/0x609
[  973.728986]  [<ffffffff814c559e>] ? udp_set_csum+0x207/0x21e
[  973.728986]  [<ffffffffa0202fe4>] l2tp_xmit_skb+0x582/0x5d7 [l2tp_core]
[  973.728986]  [<ffffffffa01b2466>] pppol2tp_xmit+0x1f2/0x25e [l2tp_ppp]
[  973.728986]  [<ffffffffa0184f59>] ppp_channel_push+0xb5/0x14a [ppp_generic]
[  973.728986]  [<ffffffffa01853ed>] ppp_write+0x104/0x11c [ppp_generic]
[  973.728986]  [<ffffffff811b2ec6>] __vfs_write+0x56/0x120
[  973.728986]  [<ffffffff8124c11d>] ? fsnotify_perm+0x27/0x95
[  973.728986]  [<ffffffff8124d41d>] ? security_file_permission+0x4d/0x54
[  973.728986]  [<ffffffff811b3f4c>] vfs_write+0xbd/0x11b
[  973.728986]  [<ffffffff811b4cb2>] SyS_write+0x5e/0x96
[  973.728986]  [<ffffffff81575ba5>] entry_SYSCALL_64_fastpath+0x18/0xa8
[  973.728986]  [<ffffffff810ae0fa>] ? trace_hardirqs_off_caller+0x121/0x12f
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      07712770
    • G
      ppp: avoid dealock on recursive xmit · 55454a56
      由 Guillaume Nault 提交于 
      In case of misconfiguration, a virtual PPP channel might send packets
back to their parent PPP interface. This typically happens in
misconfigured L2TP setups, where PPP's peer IP address is set with the
IP of the L2TP peer.
When that happens the system hangs due to PPP trying to recursively
lock its xmit path.

[  243.332155] BUG: spinlock recursion on CPU#1, accel-pppd/926
[  243.333272]  lock: 0xffff880033d90f18, .magic: dead4ead, .owner: accel-pppd/926, .owner_cpu: 1
[  243.334859] CPU: 1 PID: 926 Comm: accel-pppd Not tainted 4.8.0-rc2 #1
[  243.336010] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[  243.336018]  ffff7fffffffffff ffff8800319a77a0 ffffffff8128de85 ffff880033d90f18
[  243.336018]  ffff880033ad8000 ffff8800319a77d8 ffffffff810ad7c0 ffffffff0000039e
[  243.336018]  ffff880033d90f18 ffff880033d90f60 ffff880033d90f18 ffff880033d90f28
[  243.336018] Call Trace:
[  243.336018]  [<ffffffff8128de85>] dump_stack+0x4f/0x65
[  243.336018]  [<ffffffff810ad7c0>] spin_dump+0xe1/0xeb
[  243.336018]  [<ffffffff810ad7f0>] spin_bug+0x26/0x28
[  243.336018]  [<ffffffff810ad8b9>] do_raw_spin_lock+0x5c/0x160
[  243.336018]  [<ffffffff815522aa>] _raw_spin_lock_bh+0x35/0x3c
[  243.336018]  [<ffffffffa01a88e2>] ? ppp_push+0xa7/0x82d [ppp_generic]
[  243.336018]  [<ffffffffa01a88e2>] ppp_push+0xa7/0x82d [ppp_generic]
[  243.336018]  [<ffffffff810adada>] ? do_raw_spin_unlock+0xc2/0xcc
[  243.336018]  [<ffffffff81084962>] ? preempt_count_sub+0x13/0xc7
[  243.336018]  [<ffffffff81552438>] ? _raw_spin_unlock_irqrestore+0x34/0x49
[  243.336018]  [<ffffffffa01ac657>] ppp_xmit_process+0x48/0x877 [ppp_generic]
[  243.336018]  [<ffffffff81084962>] ? preempt_count_sub+0x13/0xc7
[  243.336018]  [<ffffffff81408cd3>] ? skb_queue_tail+0x71/0x7c
[  243.336018]  [<ffffffffa01ad1c5>] ppp_start_xmit+0x21b/0x22a [ppp_generic]
[  243.336018]  [<ffffffff81426af1>] dev_hard_start_xmit+0x15e/0x32c
[  243.336018]  [<ffffffff81454ed7>] sch_direct_xmit+0xd6/0x221
[  243.336018]  [<ffffffff814273a8>] __dev_queue_xmit+0x52a/0x820
[  243.336018]  [<ffffffff814276a9>] dev_queue_xmit+0xb/0xd
[  243.336018]  [<ffffffff81430a3c>] neigh_direct_output+0xc/0xe
[  243.336018]  [<ffffffff8146b5d7>] ip_finish_output2+0x4d2/0x548
[  243.336018]  [<ffffffff8146a8e6>] ? dst_mtu+0x29/0x2e
[  243.336018]  [<ffffffff8146d49c>] ip_finish_output+0x152/0x15e
[  243.336018]  [<ffffffff8146df84>] ? ip_output+0x74/0x96
[  243.336018]  [<ffffffff8146df9c>] ip_output+0x8c/0x96
[  243.336018]  [<ffffffff8146d55e>] ip_local_out+0x41/0x4a
[  243.336018]  [<ffffffff8146dd15>] ip_queue_xmit+0x531/0x5c5
[  243.336018]  [<ffffffff814a82cd>] ? udp_set_csum+0x207/0x21e
[  243.336018]  [<ffffffffa01f2f04>] l2tp_xmit_skb+0x582/0x5d7 [l2tp_core]
[  243.336018]  [<ffffffffa01ea458>] pppol2tp_xmit+0x1eb/0x257 [l2tp_ppp]
[  243.336018]  [<ffffffffa01acf17>] ppp_channel_push+0x91/0x102 [ppp_generic]
[  243.336018]  [<ffffffffa01ad2d8>] ppp_write+0x104/0x11c [ppp_generic]
[  243.336018]  [<ffffffff811a3c1e>] __vfs_write+0x56/0x120
[  243.336018]  [<ffffffff81239801>] ? fsnotify_perm+0x27/0x95
[  243.336018]  [<ffffffff8123ab01>] ? security_file_permission+0x4d/0x54
[  243.336018]  [<ffffffff811a4ca4>] vfs_write+0xbd/0x11b
[  243.336018]  [<ffffffff811a5a0a>] SyS_write+0x5e/0x96
[  243.336018]  [<ffffffff81552a1b>] entry_SYSCALL_64_fastpath+0x13/0x94

The main entry points for sending packets over a PPP unit are the
.write() and .ndo_start_xmit() callbacks (simplified view):

.write(unit fd) or .ndo_start_xmit()
       \
        CALL ppp_xmit_process()
               \
                LOCK unit's xmit path (ppp->wlock)
                |
                CALL ppp_push()
                       \
                        LOCK channel's xmit path (chan->downl)
                        |
                        CALL lower layer's .start_xmit() callback
                               \
                                ... might recursively call .ndo_start_xmit() ...
                               /
                        RETURN from .start_xmit()
                        |
                        UNLOCK channel's xmit path
                       /
                RETURN from ppp_push()
                |
                UNLOCK unit's xmit path
               /
        RETURN from ppp_xmit_process()

Packets can also be directly sent on channels (e.g. LCP packets):

.write(channel fd) or ppp_output_wakeup()
       \
        CALL ppp_channel_push()
               \
                LOCK channel's xmit path (chan->downl)
                |
                CALL lower layer's .start_xmit() callback
                       \
                        ... might call .ndo_start_xmit() ...
                       /
                RETURN from .start_xmit()
                |
                UNLOCK channel's xmit path
               /
        RETURN from ppp_channel_push()

Key points about the lower layer's .start_xmit() callback:

  * It can be called directly by a channel fd .write() or by
    ppp_output_wakeup() or indirectly by a unit fd .write() or by
    .ndo_start_xmit().

  * In any case, it's always called with chan->downl held.

  * It might route the packet back to its parent unit using
    .ndo_start_xmit() as entry point.

This patch detects and breaks recursion in ppp_xmit_process(). This
function is a good candidate for the task because it's called early
enough after .ndo_start_xmit(), it's always part of the recursion
loop and it's on the path of whatever entry point is used to send
a packet on a PPP unit.

Recursion detection is done using the per-cpu ppp_xmit_recursion
variable.

Since ppp_channel_push() too locks the channel's xmit path and calls
the lower layer's .start_xmit() callback, we need to also increment
ppp_xmit_recursion there. However there's no need to check for
recursion, as it's out of the recursion loop.
Reported-by: NFeng Gao <gfree.wind@gmail.com>
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      55454a56
    • S
      xgbe: constify get_netdev_ops and get_ethtool_ops · ce0b15d1
      由 stephen hemminger 提交于 
      Casting away const is bad practice. Since this is ARM specific driver
don't have hardware actually test this.

Having getter functions for ops is really unnecessary code bloat, but
not going to touch that.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ce0b15d1
    • D
      Merge branch 'dsa-mdb-support' · 07469f8c
      由 David S. Miller 提交于 
      Vivien Didelot says:

====================
net: dsa: add MDB support

This patchset adds the switchdev MDB object support to the DSA layer.

The MDB support for the mv88e6xxx driver is very similar to the FDB
support. The FDB operations care about unicast addresses while the MDB
operations care about multicast addresses.

Both operation set load/purge/dump the Address Translation Table (ATU),
thus common code is used.

Changes in v2 based on Andrew's comments:
  - drop "group" in multicast database related doc and comment
  - change _one for more relevant _fid in mv88e6xxx_port_db_dump_one
  - return -EOPNOTSUPP if switchdev obj ID is neither _FDB nor _MDB
====================
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      07469f8c
    • V
      net: dsa: mv88e6xxx: add MDB support · 7df8fbdd
      由 Vivien Didelot 提交于 
      Add support for the MDB operations. This consists of
loading/purging/dumping multicast addresses for a given port in the ATU.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7df8fbdd
    • V
      net: dsa: mv88e6xxx: make switchdev DB ops generic · 83dabd1f
      由 Vivien Didelot 提交于 
      The MDB support for the mv88e6xxx driver will be very similar to the FDB
support, since it consists of loading/purging/dumping address to/from
the Address Translation Unit (ATU).

Prepare the support for MDB by making the FDB code accessing the ATU
generic. The FDB operations now provide access to the unicast addresses
while the MDB operations will provide access to the multicast addresses.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      83dabd1f
    • V
      net: dsa: add MDB support · 8df30255
      由 Vivien Didelot 提交于 
      Add SWITCHDEV_OBJ_ID_PORT_MDB support to the DSA layer.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      8df30255
    • D
      Merge branch 'liquidio-CN23XX-part-1' · dbeb714a
      由 David S. Miller 提交于 
      Raghu Vatsavayi says:

====================
liquidio CN23XX support

Following patchset adds support for new device "CN23XX" in
liquidio family of adapters. As adviced by you I have split
the previous V3 patch of 18 patches into two halves. This
first patchset has first 10 patches, which are tested against
net-next. I will post the second half after this one.

This V4 patch also addressed all the comments from previous
submission:
1) Avoid busy loop while reading registers.
2) Other minor comments about debug messages and constants.

Please apply patches in following order as some of the
patches depend on earlier patches.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      dbeb714a
    • R
      liquidio: CN23XX firmware download · c0eab5b3
      由 Raghu Vatsavayi 提交于 
      Add firmware download support for cn23xx device.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c0eab5b3
    • R
      liquidio: MSIX support for CN23XX · 5b07aee1
      由 Raghu Vatsavayi 提交于 
      This patch adds support msix interrupt for cn23xx device.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5b07aee1
    • R
      liquidio: CN23XX queue manipulation · 1b7c55c4
      由 Raghu Vatsavayi 提交于 
      This patch adds support for cn23xx queue manipulation.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1b7c55c4
    • R
      liquidio: CN23XX register setup · 3451b97c
      由 Raghu Vatsavayi 提交于 
      Adds support for initializing cn23xx device registers
related to mac, input/output and pf global config.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3451b97c
    • R
      liquidio: CN23XX device init and sriov config · 72c00912
      由 Raghu Vatsavayi 提交于 
      Add support for cn23xx device init and sriov queue config.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      72c00912
    • R
      liquidio: CN23XX queue definitions · e86b1ab6
      由 Raghu Vatsavayi 提交于 
      Add support for cn23xx specific queue definitions and
features.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e86b1ab6
    • R
      liquidio: CN23XX register definitions · 5bc67f58
      由 Raghu Vatsavayi 提交于 
      This patch adds register definitions and structures for new
device cn23xx.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      5bc67f58
    • R
      liquidio: Common enable irq function · cd8b1eb4
      由 Raghu Vatsavayi 提交于 
      Add support of common irq enable functionality for both
iq(instruction queue) and oq(output queue).
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cd8b1eb4
    • R
      liquidio: Firmware version management · 83101ce3
      由 Raghu Vatsavayi 提交于 
      This patch contains changes for firmware version management.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      83101ce3
    • R
      liquidio: Consolidate common functionality · 32581245
      由 Raghu Vatsavayi 提交于 
      Consolidate common functionality of various devices
from different files into lio_core.c/octeon_console.c.
Signed-off-by: NDerek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: NSatanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      32581245
    • G
      net: wan: sbni: Spelling s/acknoweledge/acknowledge/, Grammar · 650097cd
      由 Geert Uytterhoeven 提交于 
      Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      650097cd
    • J
      net: systemport: constify ethtool_ops structures · c1ab0e9c
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c1ab0e9c
    • J
      dwc_eth_qos: constify ethtool_ops structures · 777065e5
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      777065e5
    • J
      net: hisilicon: constify ethtool_ops structures · bc6f0136
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      bc6f0136
    • J
      net: bcmgenet: constify ethtool_ops structures · 70591ab9
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      70591ab9
    • J
      net: ethernet: et131x: constify ethtool_ops structures · 1eff7002
      由 Julia Lawall 提交于 
      Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops.  These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };

@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;

@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)

@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1eff7002
  3. 31 8月, 2016 8 次提交
    • A
      qede: hide 32-bit compile warning · 84fd1b19
      由 Arnd Bergmann 提交于 
      The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:

drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
      buf[cnt++] = QEDE_TQSTATS_DATA(edev,
                               ^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
      buf[cnt++] = QEDE_TQSTATS_DATA(edev,
                      ^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2 ("qede: Add support for per-queue stats.")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      84fd1b19
    • A
      ravb: avoid unused function warnings · 1ddcf41f
      由 Arnd Bergmann 提交于 
      When CONFIG_PM_SLEEP is disabled, we get a couple of harmless warnings:

drivers/net/ethernet/renesas/ravb_main.c:2117:12: error: 'ravb_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/renesas/ravb_main.c:2104:12: error: 'ravb_suspend' defined but not used [-Werror=unused-function]

The simplest solution here is to replace the #ifdef with __maybe_unused
annotations, which lets the compiler do the right thing by itself.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0184165b ("ravb: add sleep PM suspend/resume support")
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1ddcf41f
    • D
      Merge branch 'mpls-fragmentation-and-gso-fixes' · 7ba9d103
      由 David S. Miller 提交于 
      David Ahern says:

====================
net: mpls: fragmentation and gso fixes for locally originated traffic

This series fixes mtu and fragmentation for tunnels using lwtunnel
output redirect, and fixes GSO for MPLS for locally originated traffic
reported by Lennert Buytenhek.

A follow on series will address fragmentation and GSO for forwarded
MPLS traffic. Hardware offload of GSO with MPLS also needs to be
addressed.

Simon: Can you verify this works with OVS for single and multiple
       labels?

v4
- more updates to mpls_gso_segment per Alex's comments (thanks, Alex)
- updates to teaching OVS about marking MPLS labels as the network header

v3
- updates to mpls_gso_segment per Alex's comments
- dropped skb->encapsulation = 1 from mpls_xmit per Alex's comment

v2
- consistent use of network_header in skb to fix GSO for MPLS
- update MPLS code in OVS to network_header and inner_network_header
====================
Tested-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7ba9d103
    • D
      net: veth: Set features for MPLS · 607fca9a
      由 David Ahern 提交于 
      veth does not really transmit packets only moves the skb from one
netdev to another so gso and checksum is not really needed. Add
the features to mpls_features to get the same benefit and performance
with MPLS as without it.
Reported-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      607fca9a
    • D
      net: mpls: Fixups for GSO · 48d2ab60
      由 David Ahern 提交于 
      As reported by Lennert the MPLS GSO code is failing to properly segment
large packets. There are a couple of problems:

1. the inner protocol is not set so the gso segment functions for inner
   protocol layers are not getting run, and

2  MPLS labels for packets that use the "native" (non-OVS) MPLS code
   are not properly accounted for in mpls_gso_segment.

The MPLS GSO code was added for OVS. It is re-using skb_mac_gso_segment
to call the gso segment functions for the higher layer protocols. That
means skb_mac_gso_segment is called twice -- once with the network
protocol set to MPLS and again with the network protocol set to the
inner protocol.

This patch sets the inner skb protocol addressing item 1 above and sets
the network_header and inner_network_header to mark where the MPLS labels
start and end. The MPLS code in OVS is also updated to set the two
network markers.

>From there the MPLS GSO code uses the difference between the network
header and the inner network header to know the size of the MPLS header
that was pushed. It then pulls the MPLS header, resets the mac_len and
protocol for the inner protocol and then calls skb_mac_gso_segment
to segment the skb.

Afterward the inner protocol segmentation is done the skb protocol
is set to mpls for each segment and the network and mac headers
restored.
Reported-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      48d2ab60
    • R
      net: lwtunnel: Handle fragmentation · 14972cbd
      由 Roopa Prabhu 提交于 
      Today mpls iptunnel lwtunnel_output redirect expects the tunnel
output function to handle fragmentation. This is ok but can be
avoided if we did not do the mpls output redirect too early.
ie we could wait until ip fragmentation is done and then call
mpls output for each ip fragment.

To make this work we will need,
1) the lwtunnel state to carry encap headroom
2) and do the redirect to the encap output handler on the ip fragment
(essentially do the output redirect after fragmentation)

This patch adds tunnel headroom in lwtstate to make sure we
account for tunnel data in mtu calculations during fragmentation
and adds new xmit redirect handler to redirect to lwtunnel xmit func
after ip fragmentation.

This includes IPV6 and some mtu fixes and testing from David Ahern.
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      14972cbd
    • E
      net: batch calls to flush_all_backlogs() · 41852497
      由 Eric Dumazet 提交于 
      After commit 145dd5f9 ("net: flush the softnet backlog in process
context"), we can easily batch calls to flush_all_backlogs() for all
devices processed in rollback_registered_many()

Tested:

Before patch, on an idle host.

modprobe dummy numdummies=10000
perf stat -e context-switches -a rmmod dummy

 Performance counter stats for 'system wide':

         1,211,798      context-switches

       1.302137465 seconds time elapsed

After patch:

perf stat -e context-switches -a rmmod dummy

 Performance counter stats for 'system wide':

           225,523      context-switches

       0.721623566 seconds time elapsed
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      41852497
    • M
      ixgbe: Eliminate useless message and improve logic · ae3cb8cb
      由 Mark Rustad 提交于 
      Remove a useless log message and improve the logic for setting
a PHY address from the contents of the MNG_IF_SEL register.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ae3cb8cb