Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NDavid Hubbard <david.c.hubbard@gmail.com>

The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution.  This patch extends the
LM70 driver to support the TMP121.  The TMP123 differs in pin assign-
ment.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).

Other fixes:  doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: NKaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: NJean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Add document about bfin-gpio when requesting a pin
both as gpio and gpio interrupt.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

Introduce a new kernel parameter `coredump_filter'.  Setting a value to
this parameter causes the default bitmask of coredump_filter to be
changed.

It is useful for users to change coredump_filter settings for the whole
system at boot time.  Without this parameter, users have to change
coredump_filter settings for each /proc/<pid>/ in an initializing script.
Signed-off-by: NHidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reformat text to (mostly) stay within 80 columns of text.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add some (more) early_param boot options to kernel-parameters.txt.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add info on how to use DOC: sections in kernel-doc.  DOC: sections enable
the addition of inline source file comments that are general in nature
instead of being specific to a function, struct, union, enum, or typedef.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update Documentation/s390/ files to reflect changed header files
locations.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update several Documentation/ files and a few sub-dir files (only one
change in each) to reflect changed header files locations.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add documentation on how to use kernel-doc for function parameters
that are "..." (varargs).
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allows kprobes to probe __exit routine.  This adds flags member to struct
kprobe.  When module is freed(kprobes hooks module_notifier to get this
event), kprobes which probe the functions in that module are set to "Gone"
flag to the flags member.  These "Gone" probes are never be enabled.
Users can check the GONE flag through debugfs.

This also removes mod_refcounted, because we couldn't free a module if
kprobe incremented the refcount of that module.

[akpm@linux-foundation.org: document some locking]
[mhiramat@redhat.com: bugfix: pass aggr_kprobe to arch_remove_kprobe]
[mhiramat@redhat.com: bugfix: release old_p's insn_slot before error return]
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Acked-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated.  This in turn happens only when
someone tells the chip to read its temperature sensors.  Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

f_op->poll is the only vfs operation which is not allowed to sleep.  It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions.  The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.

This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events.  The
only added overhead is an extra function call during wake up and
negligible.

This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.

While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.

* s/type * symbol/type *symbol/		   : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c

Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An unfortunate feature of the Unevictable LRU work was that reclaiming an
anonymous page involved an extra scan through the anon_vma: to check that
the page is evictable before allocating swap, because the swap could not
be freed reliably soon afterwards.

Now try_to_free_swap() has replaced remove_exclusive_swap_page(), that's
not an issue any more: remove try_to_munlock() call from
shrink_page_list(), leaving it to try_to_munmap() to discover if the page
is one to be culled to the unevictable list - in which case then
try_to_free_swap().

Update unevictable-lru.txt to remove comments on the try_to_munlock() in
shrink_page_list(), and shorten some lines over 80 columns.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: NRik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This change introduces two new sysctls to /proc/sys/vm:
dirty_background_bytes and dirty_bytes.

dirty_background_bytes is the counterpart to dirty_background_ratio and
dirty_bytes is the counterpart to dirty_ratio.

With growing memory capacities of individual machines, it's no longer
sufficient to specify dirty thresholds as a percentage of the amount of
dirtyable memory over the entire system.

dirty_background_bytes and dirty_bytes specify quantities of memory, in
bytes, that represent the dirty limits for the entire system.  If either
of these values is set, its value represents the amount of dirty memory
that is needed to commence either background or direct writeback.

When a `bytes' or `ratio' file is written, its counterpart becomes a
function of the written value.  For example, if dirty_bytes is written to
be 8096, 8K of memory is required to commence direct writeback.
dirty_ratio is then functionally equivalent to 8K / the amount of
dirtyable memory:

	dirtyable_memory = free pages + mapped pages + file cache

	dirty_background_bytes = dirty_background_ratio * dirtyable_memory
		-or-
	dirty_background_ratio = dirty_background_bytes / dirtyable_memory

		AND

	dirty_bytes = dirty_ratio * dirtyable_memory
		-or-
	dirty_ratio = dirty_bytes / dirtyable_memory

Only one of dirty_background_bytes and dirty_background_ratio may be
specified at a time, and only one of dirty_bytes and dirty_ratio may be
specified.  When one sysctl is written, the other appears as 0 when read.

The `bytes' files operate on a page size granularity since dirty limits
are compared with ZVC values, which are in page units.

Prior to this change, the minimum dirty_ratio was 5 as implemented by
get_dirty_limits() although /proc/sys/vm/dirty_ratio would show any user
written value between 0 and 100.  This restriction is maintained, but
dirty_bytes has a lower limit of only one page.

Also prior to this change, the dirty_background_ratio could not equal or
exceed dirty_ratio.  This restriction is maintained in addition to
restricting dirty_background_bytes.  If either background threshold equals
or exceeds that of the dirty threshold, it is implicitly set to half the
dirty threshold.
Acked-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Show node to memory section relationship with symlinks in sysfs

Add /sys/devices/system/node/nodeX/memoryY symlinks for all
the memory sections located on nodeX.  For example:
/sys/devices/system/node/node1/memory135 -> ../../memory/memory135
indicates that memory section 135 resides on node1.

Also revises documentation to cover this change as well as updating
Documentation/ABI/testing/sysfs-devices-memory to include descriptions
of memory hotremove files 'phys_device', 'phys_index', and 'state'
that were previously not described there.

In addition to it always being a good policy to provide users with
the maximum possible amount of physical location information for
resources that can be hot-added and/or hot-removed, the following
are some (but likely not all) of the user benefits provided by
this change.
Immediate:
  - Provides information needed to determine the specific node
    on which a defective DIMM is located.  This will reduce system
    downtime when the node or defective DIMM is swapped out.
  - Prevents unintended onlining of a memory section that was
    previously offlined due to a defective DIMM.  This could happen
    during node hot-add when the user or node hot-add assist script
    onlines _all_ offlined sections due to user or script inability
    to identify the specific memory sections located on the hot-added
    node.  The consequences of reintroducing the defective memory
    could be ugly.
  - Provides information needed to vary the amount and distribution
    of memory on specific nodes for testing or debugging purposes.
Future:
  - Will provide information needed to identify the memory
    sections that need to be offlined prior to physical removal
    of a specific node.

Symlink creation during boot was tested on 2-node x86_64, 2-node
ppc64, and 2-node ia64 systems.  Symlink creation during physical
memory hot-add tested on a 2-node x86_64 system.
Signed-off-by: NGary Hade <garyhade@us.ibm.com>
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These are only ever assigned constant strings and never modified.

This was noticed because Wolfram Sang needed to cast the result of
of_get_property() in order to assign it to the name field of a struct
uio_info.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates UIO documentation with the changes introduced by
previous UIO patch.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While reading Documentation/kobject.txt:

  Note kobject_rename does perform any locking or have a solid notion of
  what names are valid so the provide must provide their own sanity checking
  and serialization.

I expect better: You never see me hard with time word making sentence
coherent stuff.  Ever.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Acked-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reported-by: NBruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx

It's spelled "firmware".
Signed-off-by: NNick Andrew <nick@nick-andrew.net>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: NFrederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

- (better, more, bigger ...) then -> (...) than
Signed-off-by: NFrederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch adds the Kconfig option "CONFIG_OCFS2_FS_POSIX_ACL"
and mount options "acl" to enable acls in Ocfs2.
Signed-off-by: NTiger Yang <tiger.yang@oracle.com>
Signed-off-by: NMark Fasheh <mfasheh@suse.com>

/proc/*/stack adds the ability to query a task's stack trace. It is more
useful than /proc/*/wchan as it provides full stack trace instead of single
depth. Example output:

	$ cat /proc/self/stack
	[<c010a271>] save_stack_trace_tsk+0x17/0x35
	[<c01827b4>] proc_pid_stack+0x4a/0x76
	[<c018312d>] proc_single_show+0x4a/0x5e
	[<c016bdec>] seq_read+0xf3/0x29f
	[<c015a004>] vfs_read+0x6d/0x91
	[<c015a0c1>] sys_read+0x3b/0x60
	[<c0102eda>] syscall_call+0x7/0xb
	[<ffffffff>] 0xffffffff

[add save_stack_trace_tsk() on mips, ACK Ralf --adobriyan]
Signed-off-by: NKen Chen <kenchen@google.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

Add kbuild.txt to Documentation/kbuild
More stuff can be added later - at least we have
som of the varous environment variables documented now.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Create a kconfig user assistance guide, with a few tips and hints
about using menuconfig, xconfig, and gconfig.

Mostly contains user interface, environment variables, and search topics,
along with mini.config/custom.config usage.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Signed-off-by: NMark Lord <mlord@pobox.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
[tobias.lorenz@gmx.net: Code beautifications and documentation added]
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for Avermedia AVer TV GO 007 FM Plus (M15C) on
saa7134 driver (PCI ID 1461:f31d).
Signed-off-by: NPham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Since the i2c driver ID will be removed in the near future we have to
modify the v4l2 debugging API to use the driver name instead of driver ID.

Note that this API is not used in applications other than v4l2-dbg.cpp
as it is for debugging and testing only.

Should anyone use the old VIDIOC_G_CHIP_IDENT, then this will be logged
with a warning that it is deprecated and will be removed in 2.6.30.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Mention the new v4l2_file_operations struct.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Update the documentation now that the v4l2_dev field is in.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Changelog [v2]:
	- Add note indicating strict isolation is not possible unless all
	  mounts of devpts use the 'newinstance' mount option.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As planed, this removes ide-scsi.

The 2.6 kernel supports direct writing to ide CD drives, which
eliminates the need for ide-scsi. ide-scsi has been unmaintained and
marked as deprecated.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James.Bottomley@HansenPartnership.com
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>