- 07 6月, 2012 31 次提交
-
-
由 Rajkumar Manoharan 提交于
program BT to control SPDT everytime while loading switch table from eeprom. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The chain index to perform IQ calibration is counted to number of valid tx chains and then used for indexing chain specific registers. If the chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0 registers for chain 1. So use real chain index instead sequential one. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Fix bad indentation & if nesting to lose about two levels of unnecessary indentation. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
The wrong ADC sample phase that happen between awake and network/full sleep will lead to improper rx noisefloor calibration. Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Also, use atomic operations to check the flags. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly to track offchannel state. Also pass the correct boolean value to ath9k_hw_startpcureceive(). Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Exposed by sparse: ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
The 'setChip' variable is unused, remove it and simplify the functions. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
MCI has to be handled only when BTCOEX is actually enabled. Check for this condition before calling MCI related functions from various reset/calibration call-sites. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
The default value that is being programmed to AR_RTC_KEEP_AWAKE is 0x2, there is no need to program it manually in various functions. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
MCI interrupts have to be enabled only when BTCOEX is actually in use. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
ASPM has to be disabled when BTCOEX is in use, do this properly by calling the bus-specific ASPM init routine after the BTCOEX scheme has been determined. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Instead of cluttering ath9k_init_device() with 'ath_softc' specific initialization code, use ath9k_init_softc() to setup driver-specific work routines, timers etc. Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Arik Nemtsov 提交于
When performing a HW restart for an AP mode interface, add stations back only after the AP is beaconing. This mimics the normal flow of STA addition on AP. Some devices (wlcore) do not support adding stations before beaconing, so this has the added benefit of making recovery work for them. Signed-off-by: NArik Nemtsov <arik@wizery.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chris Yungmann 提交于
Fixed checkpatch and sparse warnings related to aiutils.* Signed-off-by: NChris Yungmann <yungmann.chris@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The remain-on-channel time validation shouldn't depend on the value of HZ, as it does now with the check against jiffies, since then you might use a value that works on one system but not on another. Fix it by checking against a minimum that's fixed. Also add validation of the wait duration for a management frame TX since this also translates into remain-on-channel internally. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
I found this core on a BCM4322, a PCI card in the Linksys WRT610N V1. This core is not used by the driver, this patch just makes ssb show the correct name. Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Pontus Fuchs 提交于
drv_resume can get called without a prior call to drv_suspend. Consider the following steps: 1. Suspend is started but driver's drv_suspend returns error. 2. Suspend is aborted. local->wowlan flag is left set. 3. Interface is removed. 4. Suspend again. This time open_count is 0 so drv_suspend is not called and local->wowlan not cleared. 5. On resume ieee80211_reconfig will call drv_resume since local->wowlan is set. Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Chun-Yeow Yeoh 提交于
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Make mac80211 print a message when it disables HT due to the connection using WEP/TKIP or due to the AP not supporting WMM/QoS. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
For each EDCA TX queue change default settings (in STA mode) to conform old 802.11b/g channel access rules. This is needed for drivers that do not have QoS enable/disable "switch" (like rt2x00) to make them work properly with legacy APs. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Configure CWmin based on slot time for IBSS mode. This helps in increasing the beacon distribution of ath9k to accepted levels in 11a mode. Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Zero.Lin 提交于
Signed-off-by: NZero.Lin <Zero.Lin@mediatek.com> Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Similar like other drivers including iwl3945, do not configure group keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Stanislaw Gruszka 提交于
Similar like other drivers, do not configure group keys to the hardware (on Ad-Hoc mode) to make IBSS RSN work. Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com> Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Zefir Kurtisi 提交于
Updates for spectral scanning register modification for AR93x: * fix bits for spectral_scan_count * add bits for new parameters Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Alex Hung 提交于
__rfkill_switch_all() switches the state of devices of a given type; however, it does not switch devices of all type (RFKILL_TYPE_ALL). As a result, it ignores the keycode "KEY_RFKILL" from another module, i.e. eeepc-wmi. This fix is to make __rfkill_switch_all() to be able to switch not only devices of a given type but also all devices. Signed-off-by: NAlex Hung <alex.hung@canonical.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Now that we've removed all uses of the set_channel API except for the monitor channel and in libertas, clarify this. Split the libertas mesh use into a new libertas_set_mesh_channel() operation, just to keep backward compatibility, and rename the normal set_channel() to set_monitor_channel(). Also describe the desired set_monitor_channel() semantics more clearly. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless由 John W. Linville 提交于
Conflicts: drivers/net/wireless/iwlwifi/iwl-drv.c
-
- 06 6月, 2012 9 次提交
-
-
由 Stanislav Yakovlev 提交于
We separate reading of device's eeprom content from writing it back to the device's sram. Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Avinash Patil 提交于
Mark bss_config parameters as invalid before setting AP channel. This prevents from setting invalid parameters while setting AP channel to FW. Signed-off-by: NAvinash Patil <patila@marvell.com> Signed-off-by: NKiran Divekar <dkiran@marvell.com> Signed-off-by: NBing Zhao <bzhao@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Just like the AP mode patch, instead of setting the channel and then joining the mesh network, provide the channel to join the network on to the join_mesh() function. Like in AP mode, you can also give the channel to the join-mesh nl80211 command now. Unlike AP mode, it picks a default channel if none was given. As libertas uses mesh mode interfaces but has no join_mesh callback and we can't simply break it, keep some compatibility code for that case and configure the channel directly for it. In the non-libertas case, where we store the channel until join, allow setting it while the interface is down. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
If it worked (Felix says it doesn't right now), the typical use-case for WDS interfaces would be to be slaved to AP mode interfaces. Therefore, it isn't necessary to set the channel on WDS interfaces. As they don't support powersave or anything like that, they also couldn't use a different channel anyway. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of setting the channel first and then starting the AP, let cfg80211 store the channel and provide it as one of the AP settings. This means that now you have to set the channel before you can start an AP interface, but since hostapd/wpa_supplicant always do that we're OK with this change. Alternatively, it's now possible to give the channel as an attribute to the start-ap nl80211 command, overriding any preset channel. Cc: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Change cfg80211_can_beacon_sec_chan() to return true if there is no secondary channel to simplify all the current users of it. They all check the channel type before calling the function because it returns false if there's no secondary channel. Also actually document the return value. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Move the set_channel function up so it can be used by other code in this file in the future. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
There's no need for ieee80211_set_channel to check whether a change in configuration happened since ieee80211_hw_config() auto-detects it. Additionally, it's wrong to pretend the HT config for the BSS changed, it didn't, the BSS can't be up & running (AP beaconing etc.) when the channel type is changed anyway. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-