These enums want to be named MLXSW_REG_QEEC_HIERARCHY_, but due to a typo
lack the second H. That is confusing and complicates searching.

But actually the enumerators should be named _HR_, because that is how
their enum type is called. So rename them as appropriate.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure to enable EMAD string TLV only after using the required firmware
version.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the trap IDs used to report layer 3 exceptions.

Trapped packets are first reported to devlink and then injected to the
kernel's receive path. All the packets have 'offload_fwd_mark' set in
order to prevent them from potentially being forwarded by the bridge
again.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, mlxsw does not differentiate between these two cases of
routes with invalid nexthops:

1. Nexthops whose nexthop device is a mlxsw upper (has a RIF), but whose
neighbour could not be resolved

2. Nexthops whose nexthop device is not a mlxsw upper (e.g., management
interface)

Up until now this did not matter and mlxsw trapped packets for both
cases using the same trap ID. However, packets that should have been
routed in hardware (case 1), but incurred a problem are considered
exceptions and should be reported to the user. The two cases should
therefore be split between two different trap IDs.

Allocate a new adjacency entry during initialization and upon the
insertion of the first route with an invalid mlxsw nexthop, program this
entry to discard packets. Packets hitting this entry will be reported
using new trap ID - "DISCARD_ROUTER3".

In the future, the entry could be written during initialization, but
currently firmware requires a valid RIF, which is not available at this
stage.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, packets that cannot be routed in hardware (e.g., nexthop
device is not upper of mlxsw), are trapped to the kernel for forwarding.
Such packets are trapped using "RTR_INGRESS0" trap. This trap also traps
packets that hit reject routes (e.g., "unreachable") so that the kernel
will generate the appropriate ICMP error message for them.

Subsequent patch will need to only report to devlink packets that hit a
reject route, which is impossible as long as "RTR_INGRESS0" is
overloaded like that.

Solve this by using "RTR_INGRESS1" trap for packets that hit reject
routes.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.

Fixes: 4a7f970f ("mlxsw: spectrum: Replace port_to_module array with array of structs")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the check generic for any possible value, not only 2 and 4.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During recreation of original unsplit ports, just simply iterate over
the whole gap and recreate whatever originally existed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code considers only split by 2 or 4. Make the base port
getting generic and allow split by 8 to be handled correctly. Generalize
the used port checks as well.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't compute the original base local port during unsplit, rather
remember it in mlxsw_sp_port structure during split port creation.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-3 the modules have 8 lanes, so split by count 2 results in
two split ports each of 4 lanes. Add a resource that can be used to
obtain local port offset in that case.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get local port offsets of split port in a separate helper function and
use it in both split and unsplit function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver assumes certain values in the PMLP register. Add checks that
verify that PMLP register provides fitting values.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass the port mapping structure down to create, module_map and other
function instead of individual values.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use constant max width value and instead of that, use the actual
width of the port. Also don't pass module value and use the value
stored in the same structure.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the initial PMLP register configuration into array of structures
instead of just simple array of module numbers.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when user does split, he is not able to distinguish if the
port cannot be split because it is already split, or because it cannot
be split at all. Add another check for split flag to distinguish this.
Also add check forbidding split when maximal width is 1.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fact that the port cannot be split further should be checked before
checking the count, so move it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the max module width is hard-coded according to ASIC type.
That is not entirely correct, as the max module width might differ
per-board. Use PMTM register to query FW for maximal width of a module.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to Spectrum-1, enforce a specific firmware version
for Spectrum-2 so that the driver and firmware are always in sync with
regards to new features.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The version adds support for querying port module type. It will be used
by a followup patch set from Jiri to make port split code more generic.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch supports an enhanced switched port analyzer that enables
selecting network traffic for analysis by a network analyzer.

SPAN agents are configured and consumed whenever a tc filter is added
with a mirror action to a new destination. The destination can either be
a physical port (e.g., swp1), a VLAN device or a gretap.

Expose the maximum number of SPAN agents and their current usage to the
user.
Signed-off-by: NDanielle Ratson <danieller@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend speed support with 400Gbps
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add new API for FW "minor" and "subminor" version validation for
sharing it between "spectrum" and "minimal" drivers.
Use it in "spectrum" driver.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the devlink reaload the extack is present, so propagate it all
the way down to register_fib_notifier() call in spectrum_router.c.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When creating netdevices for ports, put them under network namespace
that the core/parent devlink belongs to.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Follow-up patch is going to allow to reload devlink instance into
different network namespace, so use devlink_net() helper instead
of init_net.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlxsw_sp instance is not interested in events happening in other
network namespaces. So use "_net" variants for netdevice notifier
registration/unregistration and get only events which are happening in
the net the instance is in.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.

The above did not matter much until commit b5ce611f ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.

Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.

Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.

Fixes: b5ce611f ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: NAlex Kushnarov <alexanderk@mellanox.com>
Tested-by: NAlex Kushnarov <alexanderk@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register CPU port with devlink.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 5d23e415 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").

If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.

Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new version supports extended error reporting from firmware via a
new TLV in the EMAD packet. Similar to netlink extended ack.

It also fixes an issue in the PCI code that can result in false AER
errors under high Tx rate.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.

Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 275e928f ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.

Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.

Therefore, remove 56G support from mlxsw.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.

The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend existing driver for Spectrum and Spectrum-2 ASICs
to support Spectrum-3 ASIC as well.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of sp2 pci driver registration fail, fix the error path to
start with sp1 pci driver unregister.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some matches and actions are not supported on egress. Track such rules
and forbid a bind of block which contains them to egress.

With this patch, the kernel tells the user he cannot do that:
$ tc qdisc add dev ens16np1 ingress_block 22 clsact
$ tc filter add block 22 protocol 802.1q pref 2 handle 101 flower vlan_id 100 skip_sw action pass
$ tc qdisc add dev ens16np2 egress_block 22 clsact
Error: mlxsw_spectrum: Block cannot be bound to egress because it contains unsupported rules.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike Spectrum-1, the KVD (Key-value database) of Spectrum-2 is not
partitioned, so only expose the entire KVD size. This enables users to
query the total size of the KVD.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.

This patch restores the block sharing feature.

Fixes: da3eeb90 ("net: flow_offload: add list handling functions")
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>