Now that userspace is making use of kernel-provided sanitized headers for
working out supported interfaces, we need to be a bit more diligent with
matching the syscall definitions with their actual wiring/support state.

In theory it shouldn't hurt anything since sys_ni_syscall will ultimately
do the right thing, but there's also not much need to lie about legacy
x86 syscalls that we've never supported.

This tightens things up a bit for uClibc at least.
Suggested-by: NCarmelo Amoroso <carmelo.amoroso@st.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If in big-endian mode, switch the PCI bus, too.

Tested on both litte-endian and big-endian sh7785lcr.
Signed-off-by: NThomas Schwinge <thomas@codesourcery.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When DMA is enabled, sh-sci transfer begins with
 uart_start()
  sci_start_tx()
    if (cookie_tx < 0) schedule_work()
Then, starts DMA when wq scheduled, -- (A)
 process_one_work()
  work_fn_rx()
   cookie_tx = desc->submit_tx()
And finishes when DMA transfer ends, -- (B)
 sci_dma_tx_complete()
  async_tx_ack()
  cookie_tx = -EINVAL
  (possible another schedule_work())

This A to B sequence is not reentrant, since controlling variables
(for example, cookie_tx above) are not queues nor lists. So, they
must be invoked as A B A B..., otherwise results in kernel crash.

To ensure the sequence, sci_start_tx() seems to test if cookie_tx < 0
(represents "not used") to call schedule_work().
But cookie_tx will not be set (to a cookie, also means "used") until
in the middle of work queue scheduled function work_fn_tx().

This gap between the test and set allows the breakage of the sequence
under the very frequently call of uart_start().
Another gap between async_tx_ack() and another schedule_work() results
in the same issue, too.

This patch introduces a new condition "cookie_tx == 0" just to mark
it is "busy" and assign it within spin-locked region to fill the gaps.
Signed-off-by: NTakashi Yoshii <takashi.yoshii.zj@renesas.com>
Reviewed-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

CHCR of SH7763, SH7764, SH7780 and SH7785 is constitution same as SH7757.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

CHCR of SH7723 and SH7730 is constitution same as SH7724.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reviewed-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Other files are not done include definitely by asm/system.h made
include in asm/bitops.h.
This patch remove asm/system.h from asm/bitops.h.

-----
LANG=C make ARCH=sh CROSS_COMPILE=sh4-linux-gnu-
  CHK     include/linux/version.h
  CHK     include/generated/utsrelease.h
make[1]: `include/generated/machtypes.h' is up to date.
  CC      arch/sh/kernel/asm-offsets.s
In file included from include/asm-generic/getorder.h:7,
               from /home/iwamatsu/work/kernel/sh-2.6-devel/arch/sh/include/asm/page.h:187,
               from /home/iwamatsu/work/kernel/sh-2.6-devel/arch/sh/include/asm/mmu.h:38,
               from /home/iwamatsu/work/kernel/sh-2.6-devel/arch/sh/include/asm/system_32.h:5,
               from /home/iwamatsu/work/kernel/sh-2.6-devel/arch/sh/include/asm/system.h:179,
               from /home/iwamatsu/work/kernel/sh-2.6-devel/arch/sh/include/asm/bitops.h:10,
               from include/linux/bitops.h:22,
               from include/linux/thread_info.h:52,
               from include/linux/preempt.h:9,
               from include/linux/spinlock.h:50,
               from include/linux/mmzone.h:7,
               from include/linux/gfp.h:4,
               from include/linux/mm.h:8,
               from arch/sh/kernel/asm-offsets.c:13:
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34: error: implicit declaration of function 'fls'
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42: error: implicit declaration of function 'fls64'
include/linux/log2.h: In function '__roundup_pow_of_two':
include/linux/log2.h:63: error: implicit declaration of function 'fls_long'
-----
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into sh-latest

Pull s390 patches part 2 from Martin Schwidefsky:
 "Some minor improvements and one additional feature for the 3.4 merge
  window: Hendrik added perf support for the s390 CPU counters."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  [S390] register cpu devices for SMP=n
  [S390] perf: add support for s390x CPU counters
  [S390] oprofile: Allow multiple users of the measurement alert interrupt
  [S390] qdio: log all adapter characteristics
  [S390] Remove unncessary export of arch_pick_mmap_layout

Pull UML changes from Richard Weinberger:
 "Mostly bug fixes and cleanups"

* 'for-linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (35 commits)
  um: Update defconfig
  um: Switch to large mcmodel on x86_64
  MTD: Relax dependencies
  um: Wire CONFIG_GENERIC_IO up
  um: Serve io_remap_pfn_range()
  Introduce CONFIG_GENERIC_IO
  um: allow SUBARCH=x86
  um: most of the SUBARCH uses can be killed
  um: deadlock in line_write_interrupt()
  um: don't bother trying to rebuild CHECKFLAGS for USER_OBJS
  um: use the right ifdef around exports in user_syms.c
  um: a bunch of headers can be killed by using generic-y
  um: ptrace-generic.h doesn't need user.h
  um: kill HOST_TASK_PID
  um: remove pointless include of asm/fixmap.h from asm/pgtable.h
  um: asm-offsets.h might as well come from underlying arch...
  um: merge processor_{32,64}.h a bit...
  um: switch close_chan() to struct line
  um: race fix: initialize delayed_work *before* registering IRQ
  um: line->have_irq is never checked...
  ...

Pull arch/microblaze fixes from Michal Simek

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Handle TLB skip size dynamically
  microblaze: Introduce TLB skip size
  microblaze: Improve TLB calculation for small systems
  microblaze: Extend space for compiled-in FDT to 32kB
  microblaze: Clear all MSR flags on the first kernel instruction
  microblaze: Use node name instead of compatible string
  microblaze: Fix mapin_ram function
  microblaze: Highmem support
  microblaze: Use active regions
  microblaze: Show more detailed information about memory
  microblaze: Introduce fixmap
  microblaze: mm: Fix lowmem max memory size limits
  microblaze: mm: Use ZONE_DMA instead of ZONE_NORMAL
  microblaze: trivial: Fix typo fault in timer.c
  microblaze: Use vsprintf extention %pf with builtin_return_address
  microblaze: Add PVR version string for MB 8.20.b and 8.30.a
  microblaze: Fix makefile to work with latest toolchain
  microblaze: Fix typo in early_printk.c

Pull ARM platform updates from Russell King:
 "This covers platform stuff for platforms I have a direct interest in
  (iow, I have the hardware).  Essentially:
   - as we no longer support any other Acorn platforms other than RiscPC
     anymore, we can collect all that code into mach-rpc.
   - convert Acorn expansion card stuff to use IRQ allocation functions,
     and get rid of NO_IRQ from there.
   - cleanups to the ebsa110 platform to move some private stuff out of
     its header files.
   - large amount of SA11x0 updates:
   - conversion of private DMA implementation to DMA engine support
     (this actually gives us greater flexibility in drivers over the old
     API.)
   - re-worked ucb1x00 updates - convert to genirq, remove sa11x0
     dependencies, fix various minor issues
   - move platform specific sa11x0 framebuffer data into platform files
     in arch/arm instead of keeping this in the driver itself
   - update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
     for SIR transmissions as well as FIR
   - rework sa1111 support for genirq, and irq allocation
   - fix sa1111 IRQ support so it works again
   - use sparse IRQ support

  After this, I have one more pull request remaining from my current
  set, which I think is going to be the most problematical as it
  generates 8 conflicts."

Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.

* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
  ARM: 7343/1: sa11x0: convert to sparse IRQ
  ARM: 7342/2: sa1100: prepare for sparse irq conversion
  ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
  ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
  ARM: sa11x0: remove unused DMA controller definitions
  ARM: sa11x0: remove old SoC private DMA driver
  USB: sa1111: add hcd .reset method
  USB: sa1111: add OHCI shutdown methods
  USB: sa1111: reorganize ohci-sa1111.c
  USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
  USB: sa1111: sparse and checkpatch cleanups
  ARM: sa11x0: don't static map sa1111
  ARM: sa1111: use dev_err() rather than printk()
  ARM: sa1111: cleanup sub-device registration and unregistration
  ARM: sa1111: only setup DMA for DMA capable devices
  ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
  ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
  ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
  ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
  ARM: sa1111: delete unused physical GPIO register definitions
  ...

Pull networking fixes from David Miller:
 1) Name string overrun fix in gianfar driver from Joe Perches.

 2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El

 3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso.

 4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso.

 5) Add a parameter to skb_add_rx_frag() so we can fix the truesize
    adjustments in the drivers that use it.  The individual drivers
    aren't fixed by this commit, but will be dealt with using follow-on
    commits.  From Eric Dumazet.

 6) Add some device IDs to qmi_wwan driver, from Andrew Bird.

 7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node().  From
    Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: fix a potential rcu_read_lock() imbalance in rt6_fill_node()
  net: add a truesize parameter to skb_add_rx_frag()
  gianfar: Fix possible overrun and simplify interrupt name field creation
  USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces
  USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces
  USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces
  qlcnic: Bug fix for LRO
  netfilter: nf_conntrack: permanently attach timeout policy to conntrack
  netfilter: xt_CT: fix assignation of the generic protocol tracker
  netfilter: xt_CT: missing rcu_read_lock section in timeout assignment
  netfilter: cttimeout: fix dependency with l4protocol conntrack module
  netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6
  vhost: fix release path lockdep checks
  vhost: don't forget to schedule()
  tools/virtio: stub out strong barriers
  tools/virtio: add linux/hrtimer.h stub
  tools/virtio: add linux/module.h stub

Pull "ARM: device tree work" from Arnd Bergmann:
 "Most of these patches convert code from using static platform data to
  describing the hardware in the device tree.  This is only the first
  half of the changes for v3.4 because a lot of patches for this topic
  came in the last week before the merge window.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
  Document: devicetree: add OF documents for arch-mmp
  ARM: dts: append DTS file of pxa168
  ARM: mmp: append OF support on pxa168
  ARM: mmp: enable rtc clk in pxa168
  i2c: pxa: add OF support
  serial: pxa: add OF support
  arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
  ARM: OMAP2+: Remove extra ifdefs for board-generic
  ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
  ASoC: DT: Add digital microphone binding to PAZ00 board.
  ARM: dt: Add ARM PMU to tegra*.dtsi
  ARM: at91: at91sam9x5cm/dt: add leds support
  ARM: at91: usb_a9g20/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
  ARM: at91: at91sam9m10g45ek/dt: add leds support
  ARM: at91: usb_a9g20/dt: add leds support
  ARM: at91/pio: add new PIO3 features
  ARM: at91: add sam9_smc.o to at91sam9x5 build
  ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
  ARM: at91/tc: add device tree support to atmel_tclib
  ...

Pull "ARM: driver specific updates" from Arnd Bergmann:
 "These are all specific to some driver.  They are typically the
  platform side of a change in the drivers directory, such as adding a
  new driver or extending the interface to the platform.  In cases where
  there is no maintainer for the driver, or the maintainer prefers to
  have the platform changes in the same branch as the driver changes,
  the patches to the drivers are included as well.

  A much smaller set of driver updates that depend on other branches
  getting merged first will be sent later.

  The new export of tegra_chip_uid conflicts with other changes in
  fuse.c.  In rtc-sa1100.c, the global removal of IRQF_DISABLED
  conflicts with the cleanup of the interrupt handling of that driver.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up aforementioned trivial conflicts.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
  ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
  mmc: sdhci-s3c: add platform data for the second capability
  ARM: SAMSUNG: support the second capability for samsung-soc
  ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
  ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
  ARM: EXYNOS: Enable MDMA driver
  regulator: Remove bq24022 regulator driver
  rtc: sa1100: add OF support
  pxa: magician/hx4700: Convert to gpio-regulator from bq24022
  ARM: OMAP3+: SmartReflex: fix error handling
  ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
  ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
  ARM: OMAP3+: SmartReflex: misc cleanups
  ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
  ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
  ARM: OMAP3+: hwmod: add SmartReflex IRQs
  ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
  ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
  ARM: OMAP3+: SmartReflex: Add a shutdown hook
  ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
  ...

Conflicts:
	arch/arm/mach-tegra/Makefile
	arch/arm/mach-tegra/fuse.c
	drivers/rtc/rtc-sa1100.c

Pull "remoteproc/rpmsg: new subsystem" from Arnd Bergmann:
 "This new subsystem provides a common way to talk to secondary
  processors on an SoC, e.g.  a DSP, GPU or service processor, using
  virtio as the transport.  In the long run, it should replace a few
  dozen vendor specific ways to do the same thing, which all never made
  it into the upstream kernel.  There is a broad agreement that rpmsg is
  the way to go here and several vendors have started working on
  replacing their own subsystems.

  Two branches each add one virtio protocol number.  Fortunately the
  numbers were agreed upon in advance, so there are only context
  changes.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial protocol number conflict due to the mentioned additions
next to each other.

* tag 'rpmsg' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  remoteproc: cleanup resource table parsing paths
  remoteproc: remove the hardcoded vring alignment
  remoteproc/omap: remove the mbox_callback limitation
  remoteproc: remove the single rpmsg vdev limitation
  remoteproc: safer boot/shutdown order
  remoteproc: remoteproc_rpmsg -> remoteproc_virtio
  remoteproc: resource table overhaul
  rpmsg: fix build warning when dma_addr_t is 64-bit
  rpmsg: fix published buffer length in rpmsg_recv_done
  rpmsg: validate incoming message length before propagating
  rpmsg: fix name service endpoint leak
  remoteproc/omap: two Kconfig fixes
  remoteproc: make sure we're parsing a 32bit firmware
  remoteproc: s/big switch/lookup table/
  remoteproc: bail out if firmware has different endianess
  remoteproc: don't use virtio's weak barriers
  rpmsg: rename virtqueue_add_buf_gfp to virtqueue_add_buf
  rpmsg: depend on EXPERIMENTAL
  remoteproc: depend on EXPERIMENTAL
  rpmsg: add Kconfig menu
  ...

Conflicts:
	include/linux/virtio_ids.h

Pull "ARM: board specific updates" from Arnd Bergmann/Olof Johansson:
 "These changes are all specific to one board only.  We're trying to
  keep the number of board files low, but generally board level updates
  are ok on platforms that are working on moving towards DT based
  probing, which will eventually lead to removing them.

  The board-ams-delta.c board file gets a conflict between the removal
  of ams_delta_config and the addition of a lot of other data.  The
  Kconfig file has two changes in the same line, and in exynos, the
  power domain cleanup conflicts with the addition of the image sensor
  device.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
  [olof: Amended a fix for a mismerge to board-omap4panda.c]
  Signed-off-by: Olof Johansson <olof@lixom.net>"

Fixed up some fairly trivial conflicts manually.

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (82 commits)
  i.MX35-PDK: Add Camera support
  ARM : mx35: 3ds-board: add framebuffer device
  pxa/hx4700: Remove pcmcia platform_device structure
  ARM: pxa/hx4700: Reduce sleep mode battery discharge by 35%
  ARM: pxa/hx4700: Remove unwanted request for GPIO105
  ARM: EXYNOS: support Exynos4210-bus Devfreq driver on Nuri board
  ARM: EXYNOS: Register JPEG on nuri
  ARM: EXYNOS: Register JPEG on universal_c210
  ARM: S5PV210: Enable JPEG on SMDKV210
  ARM: S5PV210: Add JPEG board definition
  ARM: EXYNOS: Enable JPEG on Origen
  ARM: EXYNOS: Enable JPEG on SMDKV310
  ARM: EXYNOS: Add __init attribute to universal_camera_init()
  ARM: EXYNOS: Add __init attribute to nuri_camera_init()
  ARM: S5PV210: Enable FIMC on SMDKC110
  ARM: S5PV210: Enable FIMC on SMDKV210
  ARM: S5PV210: Enable MFC on SMDKC110
  ARM: S5PV210: Enable MFC on SMDKV210
  ARM: EXYNOS: Enable G2D on SMDKV310
  ARM: tegra: update defconfig
  ...

Pull "ARM: SoC specific updates" from Arnd Bergmann:
 "These changes are all specific to an soc family or the code for one
  soc.  Lots of work for Tegra3 this time, but also a lot of other
  platforms.  There will be another (smaller) set of soc patches later
  in the merge window for stuff that has dependencies on external trees
  or that was sent just before the merge window opened.

  The asoc tree added a few devices to the i.mx platform, which conflict
  with other devices added in the same place here.

  The tegra Makefile conflicts between a number of branches, mostly
  because of changes regarding localtimer.c, which was removed in the
  end.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fix up some trivial conflicts, including the mentioned Tegra Makefile.

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
  ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
  ARM: EXYNOS: add support JPEG
  ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
  ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
  ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
  ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
  ARM: S5PV210: Add usb otg phy control
  ARM: S3C64XX: Add usb otg phy control
  ARM: EXYNOS: Enable l2 configuration through device tree
  ARM: EXYNOS: remove useless code to save/restore L2
  ARM: EXYNOS: save L2 settings during bootup
  ARM: S5P: add L2 early resume code
  ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
  ARM: mx35: Setup the AIPS registers
  ARM: mx5: Use common function for configuring AIPS
  ARM: mx3: Setup AIPS registers
  ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
  ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
  ARM: imx: update imx_v6_v7_defconfig
  ARM: tegra: Demote EMC clock inconsistency BUG to WARN
  ...

Pull "ARM: timer cleanup work" from Arnd Bergmann:
 "These are split out from the generic soc and driver updates because
  there was a lot of conflicting work by multiple people.  Marc Zyngier
  worked on simplifying the "localtimer" interfaces, and some of the
  platforms are touching the same code as they move to device tree based
  booting.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  ARM: tegra: select USB_ULPI if USB is selected
  arm/tegra: pcie: fix return value of function
  ARM: ux500: fix compilation after local timer rework
  ARM: shmobile: remove additional __io() macro use
  ARM: local timers: make the runtime registration interface mandatory
  ARM: local timers: convert MSM to runtime registration interface
  ARM: local timers: convert exynos to runtime registration interface
  ARM: smp_twd: remove old local timer interface
  ARM: imx6q: convert to twd_local_timer_register() interface
  ARM: highbank: convert to twd_local_timer_register() interface
  ARM: ux500: convert to twd_local_timer_register() interface
  ARM: shmobile: convert to twd_local_timer_register() interface
  ARM: tegra: convert to twd_local_timer_register() interface
  ARM: plat-versatile: convert to twd_local_timer_register() interface
  ARM: OMAP4: convert to twd_local_timer_register() interface
  ARM: smp_twd: add device tree support
  ARM: smp_twd: add runtime registration support
  ARM: local timers: introduce a new registration interface
  ARM: smp_twd: make local_timer_stop a symbol instead of a #define
  ARM: mach-shmobile: default to no earlytimer
  ...

Pull "ARM: global cleanups" from Arnd Bergmann:
 "Quite a bit of code gets removed, and some stuff moved around, mostly
  the old samsung s3c24xx stuff.  There should be no functional changes
  in this series otherwise.  Some cleanups have dependencies on other
  arm-soc branches and will be sent in the second round.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

Fixed up trivial conflicts mainly due to #include's being changes on
both sides.

* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
  ep93xx: Remove unnecessary includes of ep93xx-regs.h
  ep93xx: Move EP93XX_SYSCON defines to SoC private header
  ep93xx: Move crunch code to mach-ep93xx directory
  ep93xx: Make syscon access functions private to SoC
  ep93xx: Configure GPIO ports in core code
  ep93xx: Move peripheral defines to local SoC header
  ep93xx: Convert the watchdog driver into a platform device.
  ep93xx: Use ioremap for backlight driver
  ep93xx: Move GPIO defines to gpio-ep93xx.h
  ep93xx: Don't use system controller defines in audio drivers
  ep93xx: Move PHYS_BASE defines to local SoC header file
  ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
  ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
  PM / devfreq: update the name of EXYNOS clock registers that were omitted
  PM / devfreq: update the name of EXYNOS clock register
  ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
  ARM: EXYNOS: use static declaration on regarding clock
  ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
  ARM: OMAP2+: Fix build error after merge
  ARM: S3C24XX: remove call to s3c24xx_setup_clocks
  ...

Pull "ARM: subarch maintainer updates" from Arnd Bergmann:
 "This is a collection of updates to the MAINTAINERS file, separated out
  mostly to give an overview of what has changed regarding who does
  what.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'maintainers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: tegra: update main repo and add patchwork
  MAINTAINERS: update MAINTAINERS email entry
  MAINTAINERS: update maintainer entry for pxa/hx4700
  MAINTAINERS: ARM: tegra: update Stephen's email address
  MAINTAINERS: add TI DaVinci git tree information
  MAINTAINERS: mark TI DaVinci list as "moderated"
  MAINTAINERS: remove arch/arm/mach-mx*/ from IMX entry

Pull "ARM: Non-critical bug fixes" from Ardn Bergmann:
 "Simple bug fixes that were not considered important enough for
  inclusion into 3.3.  One bug fix was originally intended for 3.3 but
  accidentally got missed, but is not marked stable because it should
  only get backported once later fixes also make it into v3.4.

  Signed-off-by: Arnd Bergmann <arnd@arndb.de>"

* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (66 commits)
  iomux-mx25.h slew rate adjusted for LCD __LD pins
  ARM: davinci: DA850: move da850_register_pm to .init.text
  ARM: davinci: cpufreq: fix compiler warning
  ARM: OMAP2+: Fix build for omap4 only builds with missing include of linux/bug.h
  ARM: OMAP2+: Fix section warnings for hsmmc_init_one
  ARM: OMAP2+: Fix build issues with missing include of linux/bug.h
  ARM: OMAP2+: gpmc-smsc911x: only register regulator for first instance
  ARM: OMAP3+: PM: VP: fix integer truncation error
  ARM: OMAP2+: PM: fix wakeupgen warning when hotplug disabled
  ARM: OMAP2+: PM: fix section mismatch with omap2_init_processor_devices()
  ARM: OMAP2: Fix section warning for n8x0 when CONFIG_MMC_OMAP is not set
  ARM: OMAP2+: Fix omap24xx_io_desc warning if SoC subtypes are not selected
  ARM: OMAP1: Fix section mismatch for omap1_init_early()
  ARM: OMAP1: Fix typo in lcd_dma.c
  ARM: OMAP: mailbox: trivial whitespace fix
  ARM: OMAP: Remove definition cpu_is_omap4430()
  ARM: OMAP2+: included some headers twice
  ARM: OMAP: clock.c: included linux/debugfs.h twice
  ARM: OMAP: don't build hwspinlock in vain
  ARM: OMAP2+: ads7846_init: put gpio_pendown into pdata if it's provided
  ...

Commit f2c31e32 (net: fix NULL dereferences in check_peer_redir() )
added a regression in rt6_fill_node(), leading to rcu_read_lock()
imbalance.

Thats because NLA_PUT() can make a jump to nla_put_failure label.

Fix this by using nla_put()

Many thanks to Ben Greear for his help
Reported-by: NBen Greear <greearb@candelatech.com>
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'asoc-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into next/boards

The asoc branch that was already merged into v3.4 contains some
board-level changes that conflict with patches we already have
here, so pull in that branch to resolve the conflicts.

Conflicts:
	arch/arm/mach-imx/mach-imx27_visstrim_m10.c
	arch/arm/mach-omap2/board-omap4panda.c
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
[olof: Amended fix for mismerge as reported by Kevin Hilman]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Now that Neponset, UCB1x00 and SA1111 are all converted to use the IRQ
allocation interfaces, we can enable sparse IRQ support for SA11x0
platforms.

In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In preparation for sa11x0 sparse irq conversion, explicitly include
mach/irqs.h as it will not be included for sparse irq.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since asm/irq.h may not include mach/irqs.h, include mach/irqs.h directly.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/mach-sa1100/assabet.c
	arch/arm/mach-sa1100/collie.c
	arch/arm/mach-sa1100/generic.c
	arch/arm/mach-sa1100/lart.c
	arch/arm/mach-sa1100/shannon.c

Conflicts:
	arch/arm/mach-sa1100/assabet.c

Remove the new unused DMA controller definitions from mach/SA-1100.h.
These are now private to the SA-11x0 DMA engine driver and contained
within the driver.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that all users are converted over to using the DMA engine API,
we can get rid of the old platform dependent DMA driver.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Conflicts:
	arch/arm/common/sa1111.c
	arch/arm/mach-sa1100/neponset.c

Fixed:
	arch/arm/mach-sa1100/assabet.c
for the neponset changes

skb_add_rx_frag() API is misleading.

Network skbs built with this helper can use uncharged kernel memory and
eventually stress/crash machine in OOM.

Add a 'truesize' parameter and then fix drivers in followup patches.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Space allocated for int_name_<foo> is insufficient for
maximal device name, expand it.

Code to create int_name_<foo> is obscure, simplify it
by using sprintf.

Found by looking for unnecessary \ line continuations.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>