thread_run is used intead of kernel_thread, daemonize, and mucking
around blocking signals directly.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is on a custom board with a mapping driver access to an ST
M50LPW080 chip. This chip is probed successfully with
do_map_probe("jedec_probe",...). If I use the mtdchar interface to
perform unlock->erase->program->lock on any of the 16 eraseblocks in the
chip, the chip is left in FL_STATUS mode while the data structures
believe that the chip is in FL_READY mode. Hence, any subsequent reads
to any flash byte results in 0x80 being read.
Signed-off-by: NShashi Rao <shashi@sun.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

A new module parameter 'rptwear' specifies how many erases between
reporting wear information.  Zero means never.
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

New module parameters have been added to nandsim to
simulate:

        bitflips        random bit flips
        badblocks       blocks that are initially marked bad
        weakblocks      blocks that fail to erase after a
                        small number of erase cycles
        weakpages       pages that fail to write after a
                        small number of successful writes
        gravepages      pages that fail to read after a
                        small number of successful reads
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Enhance nandsim to be able to create more than 1 partition.
A new module parameter 'parts' may be used to specify partition
sizes.
Signed-off-by: NAdrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: NAndre Renaud <andre@bluewatersys.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.

Tested only on AT26F004.
Signed-off-by: NHans-Jürgen Koch <hjk@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The ops.len member is not initialized, because it is unused for this
operation. The length check needs to use ops.ooblen instead
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Use the functions in the ecc structure instead of the default ones,
so the override by the board driver is effective also for software ecc
code paths.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add Micron Manufacturer ID.
Signed-off-by: NShahrom Sharif <sshahrom@micron.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

 o A dependency on the processor architecture does not make sense;
   delete it.
 o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
   make those dependencies.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Delete RCS $Id string and unused debug code.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: NRodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.

This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: NMarc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

We'll need them for suspend/resume.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.

Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.

There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.

http://bugzilla.kernel.org/show_bug.cgi?id=8110Signed-off-by: NAlexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Avoid NULL pointer usage if workqueue creation failed.
Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this fixes the spinlock recursion issue. The older fix was incomplete.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I get following warnings on spar64:
Kernel unaligned access at TPC[1000c9e4] ehci_hub_control+0x54c/0x68c [ehci_hcd]

Despite of the comment in the patched code, the type cast used there
does make unaligned access. The fix was made as it's done in
ohci-hub.c.
Signed-off-by: NMax Dmitrichenko <dmitrmax@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.

From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Additional devices
Signed-off-by: NAndre Spahlinger <uenz@gmx.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this is a fix for the outstanding usb-serial issues.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
> 
> 34ef50e5 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.

This patch should fix the issue.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NCraig Schlenter <craig@codefountain.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:

Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem.  Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.

With the attached patch, the RTS/DTR lines are resetted on a close.  The
code was mainly taken from the option.c driver.

Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: NJim Radford <radford@blackbean.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: NJim Radford <radford@blackbean.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....

I use the FTDI VID 0x0403. My PID's are:

0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device

The company is "IBS Ing.-Buero Schleusener".


From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this kills residual obsoletet code from hub.c
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes last use of hardcoded number of irq to
use platfrom_get_irq.
Signed-off-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller.  The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs.  usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices.  proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is deep architecture specific magic and does should not to exist
in a driver.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds an usual_devs entry for the Nokia 6288. Originally from
Andrew with a re-diff by Phil.

From: Andrew Nayenko <relan@bk.ru>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes the duplicate supertop entries that made it into the
.21 rc kernels.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>