64-bit has X86_HT set too, so use that instead of SMP.

This also removes a include/asm-x86/processor.h ifdef.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

1. add extended_cpuid_level for 32bit
 2. add generic_identify for 64bit
 3. add early_identify_cpu for 32bit
 4. early_identify_cpu not be called by identify_cpu
 5. remove early in get_cpu_vendor for 32bit
 6. add get_cpu_cap
 7. add cpu_detect for 64bit
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

cpuid leaf 0xb provides extended topology enumeration. This interface provides
the 32-bit x2APIC id of the logical processor and it also provides a new
mechanism to detect SMT and core siblings (which provides increased
addressability).
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

When a CPU core is shut down, all of its caches need to be flushed
to prevent stale data from causing errors if the core is resumed.
Current Linux suspend code performs an assignment after the flush,
which can add dirty data back to the cache.  On some AMD platforms,
additional speculative reads have caused crashes on resume because
of this dirty data.

Relocate the cache flush to be the very last thing done before
halting.  Tie into an assembly line so the compile will not
reorder it.  Add some documentation explaining what is going
on and why we're doing this.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Acked-by: NMark Borden <mark.borden@amd.com>
Acked-by: NMichael Hohmuth <michael.hohmuth@amd.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Bytes 464..511 in the current 512byte layout of fxsave/fxrstor
frame, are reserved for SW usage. On cpu's supporting xsave/xrstor, these bytes
are used to extended the fpstate pointer in the sigcontext, which now includes
the extended state information along with fpstate information.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Uses xsave/xrstor (instead of traditional fxsave/fxrstor) in context switch
when available.

Introduces TS_XSAVE flag, which determine the need to use xsave/xrstor
instructions during context switch instead of the legacy fxsave/fxrstor
instructions. Thread-synchronous status word is already in L1 cache during
this code patch and thus minimizes the performance penality compared to
(cpu_has_xsave) checks.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Enables xsave/xrstor by turning on cr4.osxsave on cpu's which have
the xsave support. For now, features that OS supports/enabled are
FP and SSE.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch is the result of an automatic script that consolidates the
format of all the headers in include/asm-x86/.

The format:

1. No leading underscore. Names with leading underscores are reserved.
2. Pathname components are separated by two underscores. So we can
   distinguish between mm_types.h and mm/types.h.
3. Everything except letters and numbers are turned into single
   underscores.
Signed-off-by: NVegard Nossum <vegard.nossum@gmail.com>

Signed-off-by: NJaswinder Singh <jaswinder@infradead.org>

Signed-off-by: NJaswinder Singh <jaswinder@infradead.org>

  * Slight optimization when getting one's own cpu_info percpu data.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It's not used anywhere outside its single referencing file.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

The force_mwait variable iss defined either in
arch/x86/kernel/cpu/amd.c or in arch/x86/kernel/setup_64.c, but it is
only initialized and used in arch/x86/kernel/process.c. This patch
moves the declaration to arch/x86/kernel/process.c.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: michael@free-electrons.com
Signed-off-by: NIngo Molnar <mingo@elte.hu>

"idle=nomwait" disables the use of the MWAIT
instruction from both C1 (C1_FFH) and deeper (C2C3_FFH)
C-states.

When MWAIT is unavailable, the BIOS and OS generally
negotiate to use the HALT instruction for C1,
and use IO accesses for deeper C-states.

This option is useful for power and performance
comparisons, and also to work around BIOS bugs
where broken MWAIT support is advertised.

http://bugzilla.kernel.org/show_bug.cgi?id=10807
http://bugzilla.kernel.org/show_bug.cgi?id=10914Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLi Shaohua <shaohua.li@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

"idle=halt" limits the idle loop to using
the halt instruction.  No MWAIT, no IO accesses,
no C-states deeper than C1.

If something is broken in the idle code,
"idle=halt" is a less severe workaround
than "idle=poll" which disables all power savings.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

Make sure SWAPGS and PARAVIRT_ADJUST_EXCEPTION_FRAME are properly
defined when CONFIG_PARAVIRT is off.

Fixes Ingo's build failure:
arch/x86/kernel/entry_64.S: Assembler messages:
arch/x86/kernel/entry_64.S:1201: Error: invalid character '_' in mnemonic
arch/x86/kernel/entry_64.S:1205: Error: invalid character '_' in mnemonic
arch/x86/kernel/entry_64.S:1209: Error: invalid character '_' in mnemonic
arch/x86/kernel/entry_64.S:1213: Error: invalid character '_' in mnemonic
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Stephen Tweedie <sct@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

64-bit Xen pushes a couple of extra words onto an exception frame.
Add a hook to deal with them.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NYinghai Lu <yhlu.kernel@mail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The manual padding to align on cacheline size only worked in 32 bit
In 64 bit the structure was not aligned and contained wasted space.

use the compiler ____cachline_aligned to save space & properly align
this structure.

x86_64_default size goes from 9136 -> 8960
x86_64_AMD     size goes from 9136 -> 8896

built & running on 2.6.26-rc8.
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The comment says it should have been removed in 2.6.25.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

OK, so 25-mm1 gave a lockdep error which made me look into this.

The first thing that I noticed was the horrible mess; the second thing I
saw was hacks like: 71e93d15

The problem is that arch idle routines are somewhat inconsitent with
their IRQ state handling and instead of fixing _that_, we go paper over
the problem.

So the thing I've tried to do is set a standard for idle routines and
fix them all up to adhere to that. So the rules are:

  idle routines are entered with IRQs disabled
  idle routines will exit with IRQs enabled

Nearly all already did this in one form or another.

Merge the 32 and 64 bit bits so they no longer have different bugs.

As for the actual lockdep warning; __sti_mwait() did a plainly un-annotated
irq-enable.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

It is claimed that NexGen CPUs were never shipped:

   http://lkml.org/lkml/2008/4/20/179

Also, the kernel support for these chips has been broken for
a long time, the code intended to support NexGen thereby being
essentially dead.

As an outcome of the discussion that can be found using the URL
above, this patch removes the NexGen support altogether.

The changes in this patch survived a defconfig build for i386, a
couple of successful randconfig builds, as well as a runtime test,
which consisted in booting a 32-bit x86 box up to the shell prompt.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Only allocate the FPU area when the application actually uses FPU, i.e., in the
first lazy FPU trap. This could save memory for non-fpu using apps.

for example: on my system after boot, there are around 300 processes, with
only 17 using FPU.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Split the FPU save area from the task struct. This allows easy migration
of FPU context, and it's generally cleaner. It also allows the following
two optimizations:

1) only allocate when the application actually uses FPU, so in the first
lazy FPU trap. This could save memory for non-fpu using apps. Next patch
does this lazy allocation.

2) allocate the right size for the actual cpu rather than 512 bytes always.
Patches enabling xsave/xrstor support (coming shortly) will take advantage
of this.
Signed-off-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch implements the PR_GET_TSC and PR_SET_TSC prctl()
commands on the x86 platform (both 32 and 64 bit.) These
commands control the ability to read the timestamp counter
from userspace (the RDTSC instruction.)

While the RDTSC instuction is a useful profiling tool,
it is also the source of some non-determinism in ring-3.
For deterministic replay applications it is useful to be
able to trap and emulate (and record the outcome of) this
instruction.

This patch uses code earlier used to disable the timestamp
counter for the SECCOMP framework. A side-effect of this
patch is that the SECCOMP environment will now also disable
the timestamp counter on x86_64 due to the addition of the
TIF_NOTSC define on this platform.

The code which enables/disables the RDTSC instruction during
context switches is in the __switch_to_xtra function, which
already handles other unusual conditions, so normal
performance should not have to suffer from this change.
Signed-off-by: NErik Bosman <ejbosman@cs.vu.nl>
Acked-by: NArjan van de Ven  <arjan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This patch replaces numeric constant with an appropriate macro

Also 0x800000000000UL is changed to bit shifting which is complement
to the code comment (thanks hpa for notice)
Signed-off-by: NCyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Otherwise, enabling (or better, subsequent disabling) of single
stepping would cause a kernel oops on CPUs not having this MSR.

The patch could have been added a conditional to the MSR write in
user_disable_single_step(), but centralizing the updates seems safer
and (looking forward) better manageable.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Cc: Markus Metzger <markus.t.metzger@intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NJoe Perches <joe@perches.com>

 arch/x86/kernel/reboot.c      |    1 -
 include/asm-x86/elf.h         |    5 ++---
 include/asm-x86/posix_types.h |    8 +-------
 include/asm-x86/processor.h   |    3 +--
 include/asm-x86/unistd.h      |    8 +-------
 5 files changed, 5 insertions(+), 20 deletions(-)
Signed-off-by: NIngo Molnar <mingo@elte.hu>

store initial_apicid from early identify. it is could be different from
phys_proc_id later.

also print it out in /proc/cpuinfo.
Signed-off-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

add comments to the FPU structures of processor.h.
Signed-off-by: NIngo Molnar <mingo@elte.hu>

it is already defined in smp.h
Signed-off-by: NGlauber Costa <gcosta@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

In x86_64, hlt always work. in i386, we'll query the cpuinfo associated
with this cpu
Signed-off-by: NGlauber Costa <gcosta@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NIngo Molnar <mingo@elte.hu>

basic style cleanup to flush out years of neglect:

 - consistent indentation
 - whitespace fixes
 - consistent comments
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Signed-off-by: NMike Travis <travis@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch removes the mca-pentium boot option that was a noop.

besides the source code cleanup factor, this saves some text as well:

   arch/x86/kernel/cpu/bugs.o:
      text    data     bss     dec     hex filename
       651      77       4     732     2dc bugs.o.before
       631      53       4     688     2b0 bugs.o.after
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Move STACK_TOP[_MAX] out of asm/a.out.h and into asm/processor.h as they're
required whether or not A.OUT format is available.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There are already various options to disable specific cpuid bits
on the command line. They all use their own variable. Add a generic
mask to make this easier in the future.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>