The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

P3060QDS Board Overview:
Memory subsystem:
  - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
  - 128M Bytes NOR flash single-chip memory
  - 16M Bytes SPI flash
  - 8K Bytes AT24C64 I2C EEPROM
Ethernet:
  - 4x1G + 4x1G/2.5G Ethernet controllers
  - 2xRGMII + 1xMII, three VSC8641 PHYs on board
  - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB:  Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C:  Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.

During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
 - Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
 - Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

P1010RDB Overview
 -----------------
 1Gbyte DDR3 (on board DDR)
 32Mbyte 16bit NOR flash
 32Mbyte SLC NAND Flash
 256 Kbit M24256 I2C EEPROM
 128 Mbit SPI Flash memory
 I2C Board 128x8 bit memory
 SD/MMC connector to interface with the SD memory card
 2 SATA interface
         1 internal SATA connect to 2.5. 160G SATA2 HDD
         1 eSATA connector to rear panel
 USB 2.0
         x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
         x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
 eTSEC1: Connected to RGMII PHY VSC8641XKO
 eTSEC2: Connected to SGMII PHY VSC8221
 eTSEC3: Connected to SGMII PHY VSC8221 eCAN
 Two DB-9 female connectors for Field bus interface UART
 DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture.  This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P5020DS is in the same family of boards as the P4080 DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The P3041DS is in the same family of boards as the P4080DS and thus
shares the corenet_ds code.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Introduce basic support for the Freescale P1022DS reference board, based on the
Freescale BSP for this board.  This patch excludes the DIU, SSI, and MMC/SD
drivers.  Only a 36-bit DTS is provided.

Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS.
This means enabling 64-bit physical address support, increasing the maximum
zone order to 12 (to allow the DIU driver to allocate large chunks), and
clean up the audio options to disable the deprecated OSS support.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add basic support for the P4080 DS reference board.  None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the P2020RDB reference board from Freescale.

Overview of P2020RDB platform
	- DDR
	  DDR2 1G
	- NOR Flash
	  16MByte
	- NAND Flash
	  32MByte
	- 3 Ethernet interfaces
	  1) etSEC1
		- RGMII
		- connected to a 5 port Vitesse Switch(VSC7385)
		- Switch is memory mapped through eLBC interface(CS#2)
		- IRQ1
	  2) etSEC2
		- SGMII
		- connected to VSC8221
		- IRQ2
	  3) etSEC3
		- RGMII
		- connected to VSC8641
		- IRQ3
	- 2 1X PCIe interfaces
	- SD/MMC ,USB
	- SPI EEPROM
	- Serial I2C EEPROM
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for X-ES single-board computers based on the Freescale
MPC85xx processors.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Supported are Ethernet, serial console, I2C, I2C-based RTC and
temperature sensors, NOR and NAND flash, PCI, USB, CAN and Lime
display controller.

The multiplexing of FPGA interrupts onto PowerPC interrupt lines is
supported through our own fpga_pic interrupt controller driver.

For example the SJA1000 controller is level low sensitive connected to
fpga_pic line 2 and is routed to the second (of three) irq lines to
the CPU:

    can@3,100 {
            compatible = "philips,sja1000";
            reg = <3 0x100 0x80>;
            interrupts = <2 2>;
            interrupts = <2 8 1>;   // number, type, routing
            interrupt-parent = <&fpga_pic>;
    };
Signed-off-by: NSergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: NYuri Tikhonov <yur@emcraft.com>
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NDmitry Rakhchev <rda@emcraft.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Added 85xx specifc smp_ops structure.  We use ePAPR style boot release
and the MPIC for IPIs at this point.

Additionally added routines for secondary cpu entry and initializtion.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NTrent Piepho <tpiepho@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the MPC8536 process and MPC8536DS reference board.  The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.

The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.

The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds the basic support for the Wind River SBC8548 board, implemented
as powerpc.  It closely follows the implementation of the MPC8548CDS.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This adds support for the Wind River SBC8560 board, implemented as
powerpc.  It closely follows the implementation of the MPC8560ADS.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

On the majority of 85xx & 86xx we have a register that's ability to
assert HRESET_REQ to reset the board.  We refactored that code so it
can be shared between both platforms into fsl_soc.c and removed all
the duplication in each platform directory.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Renamed the mpc8544_ds.c board code to mpc85xx_ds.c to make it more
generic in prep for other boards based on the same platform.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Switch the 85xx platform over to using the FSL generic PCI code.  This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: NXianghua Xiao <x.xiao@freescale.com>
Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
Signed-off-by: NYork Sun <yorksun@freescale.com>
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Renamed the MPC8568 MDS platform code to follow other 85xx boards.  There
isn't anything specific about the 8568 MDS code that wouldn't apply to another
85xx MDS system at this point.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the MPC8568 MDS reference board
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.

Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).

This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: NVitaly Bordug <vbordug@ru.mvista.com>

This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add PCI support for setting PCI from flat device tree on 85xx specifically for
MPC8540 ADS.
Signed-off-by: NAndy Fleming <afleming@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Rename mpc85xx.c to misc.c to match the pattern established by the
8349 port - consistency is a good thing.  Also run Lindent on the
file to clean it up.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
Signed-off-by: NJon Loeliger <jdl@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This fixes up a variety of minor problems in compiling with ARCH=ppc
arising from using the merged versions of various header files.
A lot of the changes are just adding #include <asm/machdep.h> to
files that use ppc_md or smp_ops_t.

This also arranges for us to use semaphore.c, vecemu.c, vector.S and
fpu.S from arch/powerpc/kernel when compiling with ARCH=ppc.
Signed-off-by: NPaul Mackerras <paulus@samba.org>