The device tree probing for R-Car M2N (r8a7793) is added.
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using RMMI mode, it is necessary to change in probe.
Signed-off-by: NHisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Large receive offloading is known to cause problems if received packets
are passed to other host. Therefore the kernel disables it by calling
dev_disable_lro() whenever a network device is enslaved in a bridge or
forwarding is enabled for it (or globally). For virtual devices we need
to disable LRO on the underlying physical device (which is actually
receiving the packets).

Current dev_disable_lro() code handles this  propagation for a vlan
(including 802.1ad nested vlan), macvlan or a vlan on top of a macvlan.
It doesn't handle other stacked devices and their combinations, in
particular propagation from a bond to its slaves which often causes
problems in virtualization setups.

As we now have generic data structures describing the upper-lower device
relationship, dev_disable_lro() can be generalized to disable LRO also
for all lower devices (if any) once it is disabled for the device
itself.

For bonding and teaming devices, it is necessary to disable LRO not only
on current slaves at the moment when dev_disable_lro() is called but
also on any slave (port) added later.

v2: use lower device links for all devices (including vlan and macvlan)
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NVeaceslav Falico <vfalico@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was a missing break statement so we set everything to
PKT_HASH_TYPE_L3 even when we intended to use PKT_HASH_TYPE_L4.

Fixes: 5b9dfe29 ('amd-xgbe: Provide support for receive side scaling')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactored all macros used in cxgb4i as part of previously started cxgb4 macro
names cleanup. Makes them more uniform and avoids namespace collision.
Minor changes in other drivers where required as some of these macros are used
 by multiple drivers, affected drivers are iw_cxgb4, cxgb4(vf) & csiostor
Signed-off-by: NAnish Bhatt <anish@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes two issues after using iovec iterators:
- vlan_offset should be initialized to zero, otherwise unexpected offset
  will be used in skb_copy_datagram_iter()
- advance iovec iterator when vnet_hdr_sz is greater than sizeof(gso), this
  is the case when mergeable rx buffer were enabled for a virt guest.

Fixes e0b46d0e ("tun: Use iovec iterators")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/ipv4/fou.c: In function ‘ip_tunnel_encap_del_fou_ops’:
net/ipv4/fou.c:861:1: warning: no return statement in function returning non-void [-Wreturn-type]

Fixes: a8c5f90f ("ip_tunnel: Ops registration for secondary encap (fou, gue)")
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With commit d75b1ade ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. bcm_sysport_tx_poll()
always returns 0 whether or not we completed the poll quantum.

Fix this by returning either 0 when we did complete the TX ring reclaim,
or budget to trigger a repoll.

Fixes: d75b1ade ("net: less interrupt masking in NAPI")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the commit d75b1ade ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. In tx napi poll we always return 0.
So tx napi is not called again and we do not clean up the tx ring.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the build failures that result from the use of pr_debug
without the referenced char * arrays being defined.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the host uses packet encapsulation feature, the MTU may be reduced by the
host due to headroom reservation for encapsulation. This patch handles this
new MTU value.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the types of the descriptor entries in the xgbe_ring_desc struct
from u32 to __le32 to fix endian warnings issued by sparse.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to ensure the net_device's dev.parent is set before we used it
in dma_zalloc_coherent() from init_hash_table().
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix static checker warning that got introduced in commit e2ac9628
("cxgb4: Cleanup macros so they follow the same style and look consistent, part
2") due to accidental checkin of bogus line.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of calling fou and gue functions directly from ip_tunnel
use ops for these that were previously registered. This patch adds the
logic to add and remove encapsulation operations for ip_tunnel,
and modified fou (and gue) to register with ip_tunnels.

This patch also addresses a circular dependency between ip_tunnel
and fou that was causing link errors when CONFIG_NET_IP_TUNNEL=y
and CONFIG_NET_FOU=m. References to fou an gue have been removed from
ip_tunnel.c
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Standardize function pointer uses.

Convert calling style from:
	(*foo)(args...);
to:
	foo(args...);

Other miscellanea:

o Add braces around loops with single ifs on multiple lines
o Realign arguments around these functions
o Invert logic in if to return immediately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
Code adjustment

v3:
 Remove the test_bit for patch #2.

v2:
 Correct the spelling error for the comment of patch #3.

v1:
Adjust some codes to make them more reasonable.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the device is unplugged or !netif_running(), the workqueue
doesn't need to wake the device, and could return directly.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clear the flag of SCHEDULE_TASKLET in bottom_half() to avoid
re-schedule the tasklet again by workqueue.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The INIT_LIST_HEAD(&tp->rx_done) would be done in rtl_start_rx(),
so remove the unnecessary one in alloc_all_mem().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: bcm7xxx: workaround updates

This patch series contains some updates to the Broadcom BCM7xxx internal
PHY driver, including:

- removing an annonying print that would appear during interface up/down and
  suspend/resume cycles
- drop a workaround sequence for a non-production PHY revision
- add new workarounds for the latest and greatest PHY devices found out there
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY revisions E0 and F0 share the same shorter workaround initialization
sequence. Dedicate a special function for these two PHY revisions to
perform the needed workaround sequence.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY revision D0 requires a specific workaround sequence which needs to
be applied to get the HW to behave properly in all corner cases
conditions. Do this based on the revision we just read out of the HW
using a specific function.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function performs a R/RC calibration reset and will start being
used by more than one function in the next patches, create a helper
function to factor code.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bcm7445_config_init() was working around non-production version of the
PHY HW block, so just remove it entirely.

bcm7xxx_28nm_afe_config_init() was running for all PHY revisions greater
than B0, but this workaround sequence is really specific to the B0 PHY
revision, so rename the function accordingly and update the GPHY macro
to use the generic config_init callback.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bcm7xxx_28nm_config_init() can be called as frequently as needed by the
PHY library upon suspend/resume cycles and interface bring up/down, just
print the PHY revision once and for all in order not to spam kernel
logs.

Fixes: d8ebfed3 ("net: phy: bcm7xxx: utilize PHY revision in config_init")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the normal kernel debugging mechanism which also
enables dynamic_debug at the same time.

Other miscellanea:

o Remove sysctl for irda_debug
o Remove function tracing like uses (use ftrace instead)
o Coalesce formats
o Realign arguments
o Remove unnecessary OOM messages
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: phy: micrel: refactoring and KSZ8081/KSZ8091 features

This series cleans up and refactors parts of the micrel PHY driver, and
adds support for broadcast-address-disable and led-mode configuration
for KSZ8081 and KSZ8091 PHYs.

Specifically, this enables dual KSZ8081 setups (which are limited to
using address 0 and 3).

A follow up series will add device-type abstraction which will allow for
further refactoring and shared initialisation code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable led-mode configuration for KSZ8081 and KSZ8091.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up led-mode setup by introducing proper defines for PHY Control
registers 1 and 2 and only passing the register to the setup function.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor led-mode error handling.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure never to update more than two bits when setting the led mode,
something which could for example change the reference-clock setting.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable PHY address 0 as the broadcast address, so that it can be used
as a unique (non-broadcast) address on a shared bus.

Note that this can also be configured using the B-CAST_OFF pin on
KSZ9091, but that KSZ8081 lacks this pin and is also limited to
addresses 0 and 3.

Specifically, this allows for dual KSZ8081 setups.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor and clean up broadcast disable.

Some Micrel PHYs have a broadcast-off bit in the Operation Mode Strap
Override register which can be used to disable PHY address 0 as the
broadcast address, so that it can be used as a unique (non-broadcast)
address on a shared bus.

Note that the KSZPHY_OMSO_RMII_OVERRIDE bit is set by default on
KSZ8021/8031.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use BIT macro for bitmask definitions.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure never to update the control register with random data (an
error code) by checking the return value after reading it.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A recent commit extended the documentation of the ethernet-phy
compatible property, but placed the new paragraph under the max-speed
property.

Fixes: f00e756e ("dt: Document a compatible entry for MDIO ethernet
Phys")
Cc: devicetree@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: phy: add module_phy_driver macro

Add module_phy_driver macro that can be used by PHY drivers that only
calls phy_driver_register or phy_drivers_register (and the corresponding
unregister functions) in their module init (and exit).

This allows us to eliminate a lot of boilerplate code.

Split in three patches (actual macro and two driver change classes) in
order to facilitate review.
====================
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.

Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace module init/exit which only calls phy_driver_register with
module_phy_driver macro.

Compile tested only.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>