net: phy: micrel: clean up led-mode setup

Clean up led-mode setup by introducing proper defines for PHY Control
registers 1 and 2 and only passing the register to the setup function.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/phy/micrel.c

@@ -47,8 +47,12 @@
 #define	KSZPHY_INTCS_ALL			(KSZPHY_INTCS_LINK_UP |\
 						KSZPHY_INTCS_LINK_DOWN)
 
-/* general PHY control reg in vendor specific block. */
-#define	MII_KSZPHY_CTRL			0x1F
+/* PHY Control 1 */
+#define	MII_KSZPHY_CTRL_1			0x1e
+
+/* PHY Control 2 / PHY Control (if no PHY Control 1) */
+#define	MII_KSZPHY_CTRL_2			0x1f
+#define	MII_KSZPHY_CTRL				MII_KSZPHY_CTRL_2
 /* bitmap of PHY register to set interrupt mode */
 #define KSZPHY_CTRL_INT_ACTIVE_HIGH		BIT(9)
 #define KSZ9021_CTRL_INT_ACTIVE_HIGH		BIT(14)
@@ -158,13 +162,12 @@ static int ks8737_config_intr(struct phy_device *phydev)
 	return rc < 0 ? rc : 0;
 }
 
-static int kszphy_setup_led(struct phy_device *phydev,
-			    unsigned int reg, unsigned int shift)
+static int kszphy_setup_led(struct phy_device *phydev, u32 reg)
 {
 
 	struct device *dev = &phydev->dev;
 	struct device_node *of_node = dev->of_node;
-	int rc, temp;
+	int rc, temp, shift;
 	u32 val;
 
 	if (!of_node && dev->parent->of_node)
@@ -178,6 +181,17 @@ static int kszphy_setup_led(struct phy_device *phydev,
 		return -EINVAL;
 	}
 
+	switch (reg) {
+	case MII_KSZPHY_CTRL_1:
+		shift = 14;
+		break;
+	case MII_KSZPHY_CTRL_2:
+		shift = 4;
+		break;
+	default:
+		return -EINVAL;
+	}
+
 	temp = phy_read(phydev, reg);
 	if (temp < 0) {
 		rc = temp;
@@ -220,15 +234,14 @@ static int kszphy_config_init(struct phy_device *phydev)
 
 static int kszphy_config_init_led8041(struct phy_device *phydev)
 {
-	/* single led control, register 0x1e bits 15..14 */
-	return kszphy_setup_led(phydev, 0x1e, 14);
+	return kszphy_setup_led(phydev, MII_KSZPHY_CTRL_1);
 }
 
 static int ksz8021_config_init(struct phy_device *phydev)
 {
 	int rc;
 
-	kszphy_setup_led(phydev, 0x1f, 4);
+	kszphy_setup_led(phydev, MII_KSZPHY_CTRL_2);
 
 	rc = ksz_config_flags(phydev);
 	if (rc < 0)
@@ -243,7 +256,7 @@ static int ks8051_config_init(struct phy_device *phydev)
 {
 	int rc;
 
-	kszphy_setup_led(phydev, 0x1f, 4);
+	kszphy_setup_led(phydev, MII_KSZPHY_CTRL_2);
 
 	rc = ksz_config_flags(phydev);
 	return rc < 0 ? rc : 0;