use devm_platform_get_and_ioremap_resource() to simplify code, which
contains platform_get_resource() and devm_ioremap_resource(), it also
get the resource for use by the following code.
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add PMTU discovery tests for these encapsulations:

- IPIP
- SIT, mode ip6ip
- ip6tnl, modes ip6ip6 and ipip6
Signed-off-by: NLourdes Pedrajas <lu@pplo.net>
Reviewed-by: NStefano Brivio <sbrivio@redhat.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use internal knowledge of the mdio bus core, instead use
mdiobus_get_phy() which does the same thing.
Signed-off-by: NMichael Walle <michael@walle.cc>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Two small changes

Patch #1 increases the scale of supported IPv6 nexthops groups when each
group has one nexthop and all are using the same nexthop device, but
with a different gateway IP.

Patch #2 adjusts a register definition in accordance with recent
firmware changes.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Infrastructure Entry Delete Register (IEDR) is used to delete
entries stored in the KVD linear database. Currently, it is only
possible to delete entries of size up to 2048. Future firmware versions
will support deletion of entries of size up to 4096.

Increase the size of the field so that the driver will be able to
perform such deletions in the future, when required.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in commit fc25996e ("mlxsw: spectrum_router: Increase
scale of IPv6 nexthop groups"), each nexthop group is hashed by XOR-ing
the interface indexes of all the member nexthop devices.

To avoid many different nexthop groups ending up using the same key, the
above commit started hashing the interface indexes themselves before
they are XOR-ed.

However, in cases in which there are many nexthop groups that all use
the same nexthop device and only differ in the gateway IP, we can still
end up in a situation in which all the groups are using the same key.
This eventually leads to -EBUSY error from rhashtable during insertion.

Improve the situation by also making the gateway IP part of the key.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAlex Veber <alexve@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Tested-by: NAlex Veber <alexve@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a bus->reset() call for the mii_bus structure returns an error (e.g.:
-EPROE_DEFER) we should propagate it accordingly.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: realtek: move PHY resume delay from MAC to PHY driver

Internal PHY's from RTL8168h up may not be instantly ready after calling
genphy_resume(). So far r8169 network driver adds the needed delay, but
better handle this in the PHY driver. The network driver may miss other
places where the PHY is resumed.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Realtek PHY driver takes care of adding the needed delay now,
therefore we can remove the delay here.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal PHY's from RTL8168h up may not be instantly ready after calling
genphy_resume(). So far r8169 network driver adds the needed delay, but
better handle this in the PHY driver. The network driver may miss other
places where the PHY is resumed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:

drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:700:2-8: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:702:2-8: WARNING:
Assignment of 0/1 to bool variable
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warnings:

drivers/ptp/ptp_idt82p33.c:26:5: warning: symbol 'sync_tod_timeout' was not declared. Should it be static?
drivers/ptp/ptp_idt82p33.c:31:5: warning: symbol 'phase_snap_threshold' was not declared. Should it be static?
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/ptp/ptp_kvm.c:25:1: warning:
 symbol 'kvm_ptp_lock' was not declared. Should it be static?
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some boards do not have the RX_ER MII signal connected. Normally in such
situation, those pins would be grounded, but then again, some boards
left it electrically floating.

When sending traffic to those switch ports, one can see that the
N_SOFERR statistics counter is incrementing once per each packet. The
user manual states for this counter that it may count the number of
frames "that have the MII error input being asserted prior to or
up to the SOF delimiter byte". So the switch MAC is sampling an
electrically floating signal, and preventing proper traffic reception
because of that.

As a workaround, enable the internal weak pull-downs on the input pads
for the MII control signals. This way, a floating signal would be
internally tied to ground.

The logic levels of signals which _are_ externally driven should not be
bothered by this 40-50 KOhm internal resistor. So it is not an issue to
enable the internal pull-down unconditionally, irrespective of PHY
interface type (MII, RMII, RGMII, SGMII) and of board layout.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with improvements

Again a series with few improvements.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add workaround for hw issues with TSO on RTL8168evl. This workaround is
based on information I got from Realtek, and *should* allow to safely
enable TSO on this chip version.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the code and avoid the overhead of calling vlan_get_protocol().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At that place in rtl_init_one() we can safely use rtl8169_set_features()
to configure the chip according to the default features.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far we set RX_VLAN_8125 unconditionally, even if
NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits,
and let only rtl8169_set_features() control them.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_HIGHDMA is added to vlan_features by register_netdev(),
therefore we can omit this here.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move setting the ocp_base to rtl_init_one(). Where supported the value
is always the same, and if not supported it doesn't hurt.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each ENETC station interface (SI) has a VLAN filter list and a port
flag (PSIPVMR) by which it can be put in "VLAN promiscuous" mode, which
enables the reception of VLAN-tagged traffic even if it is not in the
VLAN filtering list.

Currently the handling of this setting works like this: the port starts
off as VLAN promiscuous, then it switches to enabling VLAN filtering as
soon as the first VLAN is installed in its filter via
.ndo_vlan_rx_add_vid. In practice that does not work out very well,
because more often than not, the first VLAN to be installed is out of
the control of the user: the 8021q module, if loaded, adds its rule for
802.1p (VID 0) traffic upon bringing the interface up.

What the user is currently seeing in ethtool is this:
ethtool -k eno2
rx-vlan-filter: on [fixed]

which doesn't match the intention of the code, but the practical reality
of having the 8021q module install its VID which has the side-effect of
turning on VLAN filtering in this driver. All in all, a slightly
confusing experience.

So instead of letting this driver switch the VLAN filtering state by
itself, just wire it up with the rx-vlan-filter feature from ethtool,
and let it be user-configurable just through that knob, except for one
case, see below.

In promiscuous mode, it is more intuitive that all traffic is received,
including VLAN tagged traffic. It appears that it is necessary to set
the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is
also temporarily enabled. On exit from promiscuous mode, the setting
made by ethtool is restored.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the VCAP IS2 will produce a single match for each frame, on
the most specific classification.

Example: a ping packet (ICMP over IPv4 over Ethernet) sent from an IP
address of 10.0.0.1 and a MAC address of 96:18:82:00:04:01 will match
this rule:

tc filter add dev swp0 ingress protocol ipv4 \
	flower skip_sw src_ip 10.0.0.1 action drop

but not this one:

tc filter add dev swp0 ingress \
	flower skip_sw src_mac 96:18:82:00:04:01 action drop

Currently the driver does not really warn the user in any way about
this, and the behavior is rather strange anyway.

The current patch is a workaround to force matches on MAC_ETYPE keys
(DMAC and SMAC) for all packets irrespective of higher layer protocol.
The setting is made at the port level.

Of course this breaks all other non-src_mac and non-dst_mac matches, so
rule exclusivity checks have been added to the driver, in order to never
have rules of both types on any ingress port.

The bits that discard higher-level protocol information are set only
once a MAC_ETYPE rule is added to a filter block, and only for the ports
that are bound to that filter block. Then all further non-MAC_ETYPE
rules added to that filter block should be denied by the ports bound to
it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-04-17

This series contains updates to e1000e and igc only.

Sasha adds partial generic segmentation offload (GSO partial) support to
the igc driver.  Also added support for translating taprio schedules
into i225 cycles in igc.  Did clean up of dead code or unused defines in
the igc driver.  Refactored the code to avoid forward declarations where
possible.  Enables the NETIF_F_HW_TC flag for igc by default.

Vinicius adds support for ETF offloading using the similar approach that
taprio offload used.

Kees Cook fixes a clang warning in the e1000e driver by moving the
declared variable either into the switch case that uses the variable or
lift them up into the main function body, to help the compiler.

Andre fixed some register overwriting when dumping registers via ethtool
for igc driver.  Also fixed support for ethtool Network Flow
Classification (NFC) queue redirection by adding the missing code needed
to enable the queue selection feature from Receive Address High (RAH)
register.  Cleans up code to remove the code bits designed to support
tc-flower filters, since this client part does not support it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BCM53125 has internal Gigabit PHYs which support interrupts as well as
statistics, make it possible to configure both of those features with a
PHY driver entry.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Displaying the virtual address at which the MDIO base register address
has been mapped is not useful and is not visible with pointer hashing in
place, replace the message with something indicating successful
registration instead.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of platform_get_irq_byname_optional() to avoid printing
messages on the kernel console that interrupts cannot be found.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the Qualcomm Atheros AR8032 Fast Ethernet PHY.

It shares many similarities with the already supported AR8030 PHY but
additionally supports MII connection to the MAC.
Signed-off-by: NDavid Bauer <mail@david-bauer.net>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2020-04-17

Here's the first bluetooth-next pull request for the 5.8 kernel:

 - Added debugfs option to control MITM flag usage during pairing
 - Added new BT_MODE socket option
 - Added support for Qualcom QCA6390 device
 - Added support for Realtek RTL8761B device
 - Added support for mSBC audio codec over USB endpoints
 - Added framework for Microsoft HCI vendor extensions
 - Added new Read Security Information management command
 - Fixes/cleanup to link layer privacy related code
 - Various other smaller cleanups & fixes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug when the user adds the first MAC address filter
via ethtool NFC mechanism.

When the first MAC address filter is added, it overwrites the default
MAC address filter configured at RAL[0] and RAH[0]. As consequence,
frames addressed to the interface MAC address are not sent to host
anymore.

This patch fixes the bug by calling igc_set_default_mac_filter() during
adapter init so the position 0 of adapter->mac_table[] is assigned to
the default MAC address.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

IGC driver has no support for tc-flower filters so this patch removes
some leftover code, probably copied from IGB driver by mistake.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The support for ethtool Network Flow Classification (NFC) queue
redirection based on destination MAC address is currently broken in IGC.
For instance, if we add the following rule, matching frames aren't
enqueued on the expected rx queue.

$ ethtool -N IFNAME flow-type ether dst 3c:fd:fe:9e:7f:71 queue 2

The issue here is due to the fact that igc_rar_set_index() is missing
code to enable the queue selection feature from Receive Address High
(RAH) register. This patch adds the missing code and fixes the issue.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Acked-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i225 device support copper mode only
PHY signal detect indication for copper fiber switch
not applicable to i225 part
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This assignment of the feature NETIF_F_HW_TC
occurs prior to the initial setup of the local
hw_features variable.

This ensures that NETIF_F_HW_TC are marked
as user changeable, and also enables it by
default when the driver loads.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

IGC_START_ITR has beed defined twice
This patch come to fix it
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes some register overwriting when dumping registers via
ethtool.

We have a total of 16 RAL registers, starting at offset 139. So RAH
offset should be 139 + 16 = 155, not 145. As result some RAL registers
are overwritten. Likewise, RAH registers are also overwritten by TDBAL,
TDBAH, TDLEN, and TDH registers.

To fix this bug while preserving the ABI, this patch re-writes RAL and
RAH registers at the end of 'regs_buff' and bumps regs->version. It also
removes some pointless comments in the middle of igc_set_regs().
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Move igc_adapter and igc_ring structures up to avoid
forward declaration
It is not necessary to forward declare these structures
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We support only copper mode
Not applicable for i225 parts
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Formally Destination bit should be kept reserved to
support legacy drivers and ignore on write/read
operation
Not applicable for i225 parts
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.

To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.

drivers/net/ethernet/intel/e1000/e1000_main.c: In function ‘e1000_xmit_frame’:
drivers/net/ethernet/intel/e1000/e1000_main.c:3143:18: warning: statement will never be executed [-Wswitch-unreachable]
 3143 |     unsigned int pull_size;
      |                  ^~~~~~~~~

[1] https://bugs.llvm.org/show_bug.cgi?id=44916Signed-off-by: NKees Cook <keescook@chromium.org>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>