- Enable msi-x link interrupts because the timer based scheduler was getting
cancelled causing the link state to be lost with repetitive card up/downs
when changing the mtu.
- Unmask mac_rmac_link interrupts only for Xframe I and prevent a spurious
link interrupt in Xframe II.
- Stop the tx queue and indicate link down when card is down
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

s2io has IOMMU overflow checking, but unfortunately it is wrong.

It didn't use the standard macros, which meant that it only worked
on POWER and SPARC because only those define DMA_ERROR_CODE. Convert it to
use the standard macros instead.

I also commented two more bugs in the IOMMU handling. It assumes
that 0 DMA addresses cannot happen, but that's not true in all IOMMU setups.
The information if a buffer has been already mapped needs to be stored
elsewhere.

Didn't fix those because it needs careful checking of the buffer handling
by the maintainers.

Cc: ram.vepa@neterion.com
Cc: santosh.rastapur@neterion.com
Cc: sivakumar.subramani@neterion.com
Cc: sreenivasa.honnur@neterion.com
Signed-off-by: NAndi Kleen <ak@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

- Added napi support when MSIX is enabled.
- Moved test_msi function from s2io_open to probe function.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

- Move all the transmit completions to a single msi-x (alarm) vector.
- Enable the continuous timer interrupt for only one transmit fifo.
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	- Seperate ring specific data
	- Initialize all configured rings with equal priority.
	- Updated boundary check for number of Rings.
	- Updated per ring statistics of rx_bytes and rx_packets.
	- Moved lro struct from struct s2io_nic to struct ring_info.
	- Access respective rx ring directly in fill_rx_buffers.
	- Moved rx_bufs_left struct s2io_nic to struct ring_info.
	- Added per ring variables -  rxd_mode, rxd_count, dev, pdev.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

- Removed rx_lock and put_lock as the buffer replenishment and
  receive completion is handled serially.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

- Removed receive buffer replenishment tasklet s2io_tasklet and instead
  allocating the receive buffers in either the interrupt handler (no napi)
  or the napi handler (napi enabled).
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

- Resubmit #3
- Added s2io_vlan_rx_kill_vid entry point function for unregistering vlan.
- Fix to aggregate vlan packets. IP offset is incremented by
  4 bytes if the packet contains vlan header.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Resubmit #2
- Transmit fifo selection based on TCP/UDP ports.
- Added tx_steering_type loadable parameter for transmit fifo selection.
  0x0 NO_STEERING: Default FIFO is selected.
  0x1 TX_PRIORITY_STEERING: FIFO is selected based on skb->priority.
  0x2 TX_DEFAULT_STEERING: FIFO is selected based on L4 Ports.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Resubmit #3
Multiqueue netwrok device support implementation.
- Added a loadable parameter "multiq" to enable/disable multiqueue support,
  by default it is disabled.
- skb->queue_mapping is not used for queue/fifo selection. FIFO selection is
  based on skb->priority.
- Added per FIFO flags FIFO_QUEUE_START and FIFO_QUEUE_STOP. Check this flag
  for starting and stopping netif queue and update the flags accordingly.
- In tx_intr_handler added a check to ensure that we have free TXDs before wak-
  ing up the queue.
- Added helper functions for queue manipulation(start/stop/wakeup) to invoke
  appropriate netif_ functions.
- Calling netif_start/stop for link up/down case respectively.

- As per Andi kleen's review comments, using skb->priority field for FIFO
  selection.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Resubmitting patch from Al Viro <viro@zeniv.linux.org.uk>, with subject -
[PATCH] s2io LRO bugs.
a) initiate_new_session() sets ->tcp_ack to ntohl(...); everything
   else stores and expects to find there the net-endian value.
b) check for monotonic timestamps in verify_l3_l4_lro_capable()
   compares the value sitting in TCP option (right there in the skb->data,
   net-endian 32bit) with the value picked from earlier packet.
   Doing that without ntohl() is an interesting idea and it might even
   work occasionally; unfortunately, it's quite broken.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes to enable multiple transmit fifos (upto a maximum of eight).
  - Moved single tx_lock from struct s2io_nic to struct fifo_info.
  - Moved single ufo_in_band_v structure from struct s2io_nic to struct
    fifo_info.
  - Assign the respective interrupt number for the transmitting fifo in the
    transmit descriptor (TXD).
- Added boundary checks for number of FIFOs enabled and FIFO length.
Signed-off-by: NSurjit Reang <surjit.reang@neterion.com>
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

s2io, rename BIT macro

BIT macro will be global definiton of (1<<x)
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Ramkrishna Vepa <ram.vepa@neterion.com>
Cc: Rastapur Santosh <santosh.rastapur@neterion.com>
Cc: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
     - Converted the macro to a function and removed call to memset
     - regarding function naming convention, for all callbacks and entry points
       will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Removed bimodal interrupt support - unused feature
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

[also, trim trailing whitespace]

- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
  packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
  variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
  register instead of de asserting by clearing the source of interrupts with
  multiple writes which causes loss of interrupts (race conditions). It is
  entirely possible that before the driver has a chance to mask the asserted
  alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
  this case Herc will keep the INTA line asserted and the bridge will not
  send a new Assert_INTA message upstream.

[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Added check to return from the traffic handling function, if the card status
  is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Removed the unused variable, intr_type, in device private structure.

[ Resolve conflicts with napi_struct changes... -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
  Packets containing corrupted data will be dropped (not transmitted) or tagged
  as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
  machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
  (undesirable PCI behaviour)is tagged as a "serious error". In such cases
  the adapter will give up its ability to be a bus master. In this situation
  the host will still be able to read internal device registers in order to
  generate an error report. A device reset is necessary to return to normal
  operation.
- In the event of a pcix data parity error, the adapter will automatically
  disable itself. Adapter_En will automatically transition from '1' to '0' and
  the adapter will enter its clean-up routine. Once the device has achieved
  quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.

[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
  "unsigned long long *" but the function takes a "u64 *" which is
  different on many 64-bit platforms. -DaveM ]
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Added support to unmask entire set of device errors and alarams.
        Alarm interrupts are generated for a myriad of purposes, ranging from
  illegal operations or requests to internal state machine errors and
  uncorrectable data corruption errors. In several cases the adapter can
  recover gracefully from unexpected events; however, in some cases, a device
  reset may be necessary. This patch handles alarms generated by all the
  blocks within the device.

  The adapter generates the following types of alarms:
        1. Link state transitions (local/remote fault) or other link-related
           problems.
        2. Problems with any device peripherals, including the EEPROM, FLASH,
           etc.
        3. Correctable ECC errors (single-bit errors) on internal data
           structures or frame data.
        4. Uncorrectable ECC errors (multi-bit errors) on internal data
           structures or frame data.
        5. State machine errors, which indicate that internal control
           structures have become corrupted.
        6. PCI related errors, including parity errors or illegal transactions.
        7. Other unexpected events.

- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
  duplicate codes.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Calling store_xmsi_data to store the MSI-X datas during initialization
  in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Making MSIX as default intr_type
- Driver will test MSI-X by issuing test MSI-X vector and if fails it will
  fallback to INTA
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

 - Checking for the return value of pci map function
 - Implemented Francois Romieu's comments on eliminating code duplication
   using goto
 - Implemented Francois Romieu's comments on using a temporary variable for
   accessing statistics structure
Signed-off-by: NVeena Parat <veena.parat@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 - Removed MSI support from driver - unused feature
 - Replaced request_mem_region with pci_request_regions
Signed-off-by: NVeena Parat <veena.parat@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 - Removed 3 buffer mode support from driver - unused feature
 - Incorporated Jeff Garzik's comments on elimination of inline typecasting
 - Code cleanup : Removed a few extra spaces
Signed-off-by: NVeena Parat <veena.parat@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.

This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.

In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.

Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Acked-by: NDave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

s2io cleanup suggestions, per discussion on mailing lists.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds PCI error recovery support to the
s2io 10-Gigabit ethernet device driver. Third revision,
blocks interrupts and the watchdog.

Tested, seems to work well.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Acked-by: NRamkrishna Vepa <Ramkrishna.Vepa@neterion.com>
Cc: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Cc: Wen Xiong <wenxiong@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

1. Added statistics for link up/down, last link up/down.
2. Statistics for memory allocated/freed.
3. Changed level of some DBG_PRINTs.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

1. Added code to count the number of memory failures.
2. Added watchdog_timer counter.
3. Changed debug level for some DBG_PRINTS.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Adding get_ringparam ethtool option.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Remove unused variables from s2io_nic structure

- Changed the memory failure printk messages to print only in debug mode

- Updated the copyright messages

(Resending; due to patch being corrupted)
Signed-off-by: NSantosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Added code to not to strip vlan tag when driver is in promiscuous mode
- Added module loadable parameter 'vlan_tag_strip" through which user can
  enable or disable vlan stripping irrespective of mode
  ( promiscuous or non-promiscuous ).
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Optimized delay to wait for command completion so as to reduce the
  initialization wait time.
- Disable differentiated services steering. By default RMAC is configured to
  steer traffic with certain DS codes to other queues. Driver must initialize
  the DS memory to 0 to make sure that DS steering will not be used by default.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removed namespace collisions due to usage of nic_t as per Ralf's patch
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

1. Fix for reset and link handling.
2. Allow for promiscuos mode and multicast state be maintained through
   ifconfig up and down.
3. Support to print adapter serial number.
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>