This add a DT compatible board specific setup for the Seagate
FreeAgent Dockstar.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for the Iomega ix2-200.
Led's and buttons working as of kernel 3.6-rc2

the 3 lines in the network interface do seem to be required as
removing either causes the network card to not be able to reach
the network (at least on my device).

Product page:
http://go.iomega.com/en/products/network-storage-desktop/storcenter-network-storage-solution/network-hard-drive-ix2-200-cloud/?partner=4735#tech_specsItem_tabSigned-off-by: NAlan M Butler <alanbutty12@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for Buffalo Linkstation LS-XHL and LS-CHLv2 using the device
tree where possible.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

This patch supplies the necessary DTS and supporting files to boot up
a Seagate GoFlex Net with 3.5.0-rc3.
Signed-off-by: NJoshua Coombs <josh.coombs@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

The two different variants of QNAP TS devices, varying by SoC, put the
GPIO keys on different GPIO lines. Hence we need two different DT
board descriptions, which share the same board-ts219.c file.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NJason Cooper <jason@lakedaemon.net>

Add support for the IB-NAS6210 and IB-NAS 6220. Describe as much as
currently possible in the devicetree files, including the NAND partitions.
Use the partition scheme of the original firmware by default.

Create a board-ib62x0.c for everything else.
Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for Iomega Iconnect system.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Tested-By: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.

Changes since last submission (V3) [Addressing comments by]:-

* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49

Changes since last submission (V2):-

* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NJamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Move all dreamplug-specific code out of board-dt.c and into
board-dreamplug.c.  This way new boards that are added during the
conversion to fdt don't clutter up board-dt.c.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

We need to absorb kirkwood_init() into kirkwood_dt_init() so that as we
convert drivers, we can remove the platform call, eg
kirkwood_rtc_init().  This maintains compatibility with non-fdt
configurations because they still call kirkwood_init() in common.c.

As drivers are converted, we will reinstate the 'static' qualifier in
common.c.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Hook these platforms restart code into the new restart hook rather than
using arch_reset().
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the *_mbus_dram_info structure into the orion platform and call it
orion_mbus_dram_info everywhere.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

PCIe may have been disabled (by kirkwood_clock_gate)
if this kernel was started by kexec.  Make sure PCIe
is enabled before attempting to access the device ID
register, otherwise the system will hang.
Signed-off-by: NEric Cooper <ecc@cmu.edu>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

This patch add audio related definitions and functions
Signed-off-by: NArnaud Patard <apatard@mandriva.com>
Acked-by: NNicolas Pitre <nico@fluxnic.net>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add a kirkwood_nand_init_rnb() call to allow boards which
have RnB line detection to register this instead of a
static delay.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Always creating the physical mapping should do no harm, so let's remove
the interface that was provided for its optional creation and make the
mapping static.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Common resource and platform device structures are moved to common.c
and only the partition table and chip delay remains a per board
parameter.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Add support for the QNAP TS-119 and TS-219 Turbo NAS devices.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Hook up I2C on Marvell Kirkwood.  Tested on a QNAP TS-219 which has
RTC connected through I2C.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The RTC and the two XOR engines are internal to the chip, and therefore
always available since they don't depend on a particular board layout.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

The 88f6192 and 88f6281 Kirkwood SoCs support two ethernet ports.
Add the platform glue that will allow board support files to
instantiate the second ethernet port.
Signed-off-by: NRonen Shitrit <rshitrit@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This adds DSA switch instantiation hooks to the orion5x and the
kirkwood ARM SoC platform code, and instantiates the DSA switch
driver on the 88F5181L FXO RD, the 88F5181L GE RD, the 6183 AP GE
RD, the Linksys WRT350n v2, and the 88F6281 RD boards.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Tested-by: NNicolas Pitre <nico@marvell.com>
Tested-by: NPeter van Valderen <linux@ddcrew.com>
Tested-by: NDirk Teurlings <dirk@upexia.nl>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Add support to the Kirkwood port for newer device models and silicon
revisions.  Instead of looking at the DEVICE_ID register, the device
version is now determined by looking at the PCI-Express device ID and
revision registers, as it is done for orion5x, and this information
is used to determine the TCLK frequency, again, as it is done for
orion5x.
Signed-off-by: NRonen Shitrit <rshitrit@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

The Marvell Kirkwood (88F6000) is a family of ARM SoCs based on a
Shiva CPU core, and features a DDR2 controller, a x1 PCIe interface,
a USB 2.0 interface, a SPI controller, a crypto accelerator, a TS
interface, and IDMA/XOR engines, and depending on the model, also
features one or two Gigabit Ethernet interfaces, two SATA II
interfaces, one or two TWSI interfaces, one or two UARTs, a
TDM/SLIC interface, a NAND controller, an I2S/SPDIF interface, and
an SDIO interface.

This patch adds supports for the Marvell DB-88F6281-BP Development
Board and the RD-88F6192-NAS and the RD-88F6281 Reference Designs,
enabling support for the PCIe interface, the USB interface, the
ethernet interfaces, the SATA interfaces, the TWSI interfaces, the
UARTs, and the NAND controller.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>