The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.

Fixes: 615f7b9b ("mac80211: add driver RSSI threshold events")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These file aren't really useful:
 - if per beacon data is required then you need to use
   radiotap or similar anyway, debugfs won't help much
 - average beacon signal is reported in station info in
   nl80211 and can be looked up with iw
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the basics required for supporting very high throughput
with mesh: include VHT information elements in beacons, probe
responses, and peering action frames, and check for compatible VHT
configurations when peering.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clear the Channel Center Frequency Segment 2 in VHT operation
IEs to avoid sending non-zero values if the SKB wasn't zeroed
before adding the VHT operation IE.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
[change commit message a bit - not necessarily just mesh related]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers may be interested in receiving A-MSDU within A-MDPU.
Not all the devices may be able to do so, make it configurable.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The direct probe step before authentication was done mostly for
two reasons:
 1) the BSS data could be stale
 2) the beacon might not have included all IEs

The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.

Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When checking if a TDLS chandef can be upgraded, IR-relaxation can be
taken into account to allow more channels.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Queued frames aren't processed during scan, which results in an inability
to complete the BA session establishment until the scan ends. Since we
can't tx frames until the BA agreement setup is complete, it might result
in a very large latency during scan.
Fix this by allowing to process queued skbs while scanning in HW. This
should be ok since the devices which support hw scan should be able
to handle tx/rx while scanning.
During SW scan, mac80211 drops any txed frames besides probes and NDPs,
so it is still needed to delay processing of the queued frames till the
SW scan is done.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.

This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Define rate_control_apply_mask_ratetbl() in order to apply ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove ieee80211_tx_rate dependency in rate_idx_match_legacy_mask(),
rate_idx_match_mcs_mask() and rate_idx_match_mask() in order to use the
previous logic to define a ratemask in rate_control_set_rates() for
station rate table. Moreover move rate mask definition logic in
rate_control_cap_mask()
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove unnecessary ieee80211_tx_info pointer from rate_control_apply_mask
signature. rate_control_apply_mask() will be used to define a ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Perform the BSS_CHANGED_BSSID action when joining an OCB network.
This is required to set the broadcast BSSID in some network drivers.
Signed-off-by: NBertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: NBertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: NBertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

At the last iteration of the loop, j may equal zero and thus
tp_list[j - 1] causes an invalid read.
Change the logic of the loop so that j - 1 is always >= 0.

Cc: stable@vger.kernel.org
Signed-off-by: NAdrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The outside if statement checks that IEEE80211_TX_INTFL_MLME_CONN_TX is
set so this condition is always true.  Checking twice upsets the static
checkers.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The iwlwifi driver was the only driver that used this, but as
it turns out it never needed it, so we can remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With this .config: http://busybox.net/~vda/kernel_config,
after deinlining these functions have sizes and callsite counts
as follows:

rate_control_rate_init: 554 bytes, 8 calls
rate_control_rate_update: 1596 bytes, 5 calls

Total size reduction: about 11 kbytes.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
CC: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With this .config: http://busybox.net/~vda/kernel_config,
after deinlining the function size is 3132 bytes and there are
7 callsites.

Total size reduction: about 20 kbytes.
Signed-off-by: NDenys Vlasenko <dvlasenk@redhat.com>
CC: John Linville <linville@tuxdriver.com>
CC: Michal Kazior <michal.kazior@tieto.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of using peer link id for AID, generate a new
AID when creating mesh STAs in the kernel peering manager.
This enables smaller TIM elements and more closely follows
the standard, and it also enables mesh to work on drivers
that require a valid AID when the STA is inserted (ath10k
firmware has this requirement, for example).

In the case of userspace-managed stations, we use the AID
from NL80211_CMD_NEW_STATION.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

According to 802.11-2012 13.3.1, a mesh STA should assign an AID
upon receipt of a mesh peering open frame rather than using the link
id of the peer.  Using the peer link id has two potential issues:
it may not be unique among the peers, and by its nature it is random,
so the TIM may not compress well.

In preparation for allocating it properly, use sta->sta.aid, but keep
the existing behavior of using the plid in the aid we send.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move mesh_plink_frame_tx() above the first caller to remove
the forward declaration.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, mac80211 calls drv_resume() on wowlan resume,
but drops any incoming frame until local->suspended is
cleared later on.

This requires the low-level driver to support a new state,
in which it is expected to fully work (as it was resumed)
but not passing rx frames yet (as they will be dropped).

iwlwifi (and probably other drivers as well) has issues
supporting such mode.

Since in the wowlan case we already short-circuit
ieee80211_reconfig, there's nothing that prevents us from
clearing local->suspend before calling drv_resume(),
and letting the low-level driver work normally.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If a TDLS station is not allowed to beacon on a channel, don't accept
a channel switch request to this channel.
Move channel building code up to avoid lockdep violations - reg_can_beacon
needs to take the wdev lock.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Move TDLS channel-switch Rx handling into an RTNL locked work. This is
required to add proper regulatory checking to incoming channel-switch
requests.
Queue incoming requests in a dedicated skb queue and handle the request
in a device-specific work to avoid deadlocking on interface removal.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If an SKB will be segmented by the driver, count it for multiple
MSDUs that are being transmitted rather than just a single.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Most of the fields in this struct use too wide types, change
that to shrink the struct from 64 to 48 bytes (on 64-bit.)

This results in a total saving of 64 bytes for each interface.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This value is only used in mesh, so move it into the new mesh
sub-struct of the station info.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case of Dynamic SMPS enable RTS/CTS for all rates.
Signed-off-by: NChaitanya T K <chaitanya.mgit@gmail.com>
[change comment]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch does the following:
- Remove unnecessary flags field used by PERR element
- Use the per target flags defined in <linux/ieee80211.h>
- Process the target only subfield based on case E2 of
  IEEE802.11-2012 13.10.9.3
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.

To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.

While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.

Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We already set a station to be associated when peering completes, both
in user space and in the kernel.  Thus we should always have an
associated sta before sending data frames to that station.

Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized.  This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.

Cc: stable@vger.kernel.org
Reported-by: NAlexis Green <agreen@cococorp.com>
Tested-by: NJesse Jones <jjones@cococorp.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When processing a PREQ or PREP it's critical to use the incoming SN. If
that is improperly done routing loops and other types of badness can
happen. But the code was always processing path messages for deactivated
paths. This path fixes that so that if we have a valid SN then we use it
to verify that it is a message we can accept. For reference the relevant
section of the standard is 13.10.8.4 which doesn't address the deactivated
path case at all.

I also included a special case for when our peer reboots or restarts
networking. This is an important case because without it there can be a
very long delay before we accept path messages from that peer. It's also a
simple case and intimately associated with processing messages for
deactivated paths so I used one patch instead of two.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The 2012 spec mentions that path SNs can be invalid when created (see
section 13.10.8.4 table 13-9) but AFAICT never talks about invalidating
SNs. Which makes sense: if we have figured out the path to a target at a
certain SN then we want to remember that fact. Failing to do so can lead
to routing loops because if we don't have a valid SN then we have no way
of knowing whether an incoming path message leads to or away from the
target.

However currently when discovery fails we zero out mpath->flags which
clears MESH_PATH_SN_VALID. This patch fixes that so that only the
discovery relevant flags are cleared.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>