The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.

Fixes: 615f7b9b ("mac80211: add driver RSSI threshold events")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These file aren't really useful:
 - if per beacon data is required then you need to use
   radiotap or similar anyway, debugfs won't help much
 - average beacon signal is reported in station info in
   nl80211 and can be looked up with iw
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the basics required for supporting very high throughput
with mesh: include VHT information elements in beacons, probe
responses, and peering action frames, and check for compatible VHT
configurations when peering.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clear the Channel Center Frequency Segment 2 in VHT operation
IEs to avoid sending non-zero values if the SKB wasn't zeroed
before adding the VHT operation IE.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
[change commit message a bit - not necessarily just mesh related]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Drivers may be interested in receiving A-MSDU within A-MDPU.
Not all the devices may be able to do so, make it configurable.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The direct probe step before authentication was done mostly for
two reasons:
 1) the BSS data could be stale
 2) the beacon might not have included all IEs

The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.

Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to transfer many items in vendor commands, support the
dumpit netlink method for them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When checking if a TDLS chandef can be upgraded, IR-relaxation can be
taken into account to allow more channels.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Sometimes we are interested in testing TDLS performance in a specific
width setting. Add the ability to disable the wider-band feature, thereby
allowing the TDLS channel width to be controlled by the BSS width.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Queued frames aren't processed during scan, which results in an inability
to complete the BA session establishment until the scan ends. Since we
can't tx frames until the BA agreement setup is complete, it might result
in a very large latency during scan.
Fix this by allowing to process queued skbs while scanning in HW. This
should be ok since the devices which support hw scan should be able
to handle tx/rx while scanning.
During SW scan, mac80211 drops any txed frames besides probes and NDPs,
so it is still needed to delay processing of the queued frames till the
SW scan is done.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As pointed out by sparse, this symbol should be static, make it so.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Merge tag 'wireless-drivers-next-for-davem-2015-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
Major changes:

iwlwifi:

* new Tx power firmware API
* bump max firmware API to 17
* fix bug in debug prints
* static checker fix
* fix unused defines
* fix command list on newest firmware

brcmfmac:

* support NVRAM loading for bcm47xx platform
* new debugfs entry for msgbuf protocol layer used with PCIe devices

ath10k:

* add spectral scan support for qca99x0
* add qca6164 support
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure to indicate to tunnel driver that key.tun_id is set,
otherwise gre won't recognize the metadata.

Fixes: d3aa45ce ("bpf: add helpers to access tunnel metadata")
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
act_bpf: remove spinlock in fast path

v1 version had a race condition in cleanup path of bpf_prog.
I tried to fix it by adding new callback 'cleanup_rcu' to 'struct tcf_common'
and call it out of act_api cleanup path, but Daniel noticed
(thanks for the idea!) that most of the classifiers already do action cleanup
out of rcu callback.
So instead this set of patches converts tcindex and rsvp classifiers to call
tcf_exts_destroy() after rcu grace period and since action cleanup logic
in __tcf_hash_release() is only called when bind and refcnt goes to zero,
it's guaranteed that cleanup() callback is called from rcu callback.
More specifically:
patches 1 and 2 - simple fixes
patches 2 and 3 - convert tcf_exts_destroy in tcindex and rsvp to call_rcu
patch 5 - removes spin_lock from act_bpf

The cleanup of actions is now universally done after rcu grace period
and in the future we can drop (now unnecessary) call_rcu from tcf_hash_destroy()
patch 5 is using synchronize_rcu() in act_bpf replacement path, since it's
very rare and alternative of dynamically allocating 'struct tcf_bpf_cfg' just
to pass it to call_rcu looks even less appealing.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to act_gact/act_mirred, act_bpf can be lockless in packet processing
with extra care taken to free bpf programs after rcu grace period.
Replacement of existing act_bpf (very rare) is done with synchronize_rcu()
and final destruction is done from tc_action_ops->cleanup() callback that is
called from tcf_exts_destroy()->tcf_action_destroy()->__tcf_hash_release() when
bind and refcnt reach zero which is only possible when classifier is destroyed.
Previous two patches fixed the last two classifiers (tcindex and rsvp) to
call tcf_exts_destroy() from rcu callback.

Similar to gact/mirred there is a race between prog->filter and
prog->tcf_action. Meaning that the program being replaced may use
previous default action if it happened to return TC_ACT_UNSPEC.
act_mirred race betwen tcf_action and tcfm_dev is similar.
In all cases the race is harmless.
Long term we may want to improve the situation by replacing the whole
tc_action->priv as single pointer instead of updating inner fields one by one.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust destroy path of cls_rsvp to call tcf_exts_destroy() after
rcu grace period.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust destroy path of cls_tcindex to call tcf_exts_destroy() after
rcu grace period.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix harmless typo and avoid unnecessary copy of empty 'prog' into
unused 'strcut tcf_bpf_cfg old'.

Fixes: f4eaed28 ("act_bpf: fix memory leaks when replacing bpf programs")
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcf_hash_destroy() used once. Make it static.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Kconfig option AVERAGE and its implementation has been removed by
commit f4e774f5 ("average: remove out-of-line implementation").
Remove the dead build rule in lib/Makefile.
Signed-off-by: NValentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Major changes in ath10k:

* add spectral scan support for qca99x0
* add qca6164 support

Below compilation warnings are observed in gcc version 4.8.2.
Even though it's not seen in bit older gcc versions (for ex, 4.7.3),
It's good to fix it by changing format specifier from %d to
%zd in wmi pull phyerr functions.

wmi.c: In function 'ath10k_wmi_op_pull_phyerr_ev':
wmi.c:3567:8: warning: format '%d' expects argument of type 'int',
              but argument 4 has type 'long unsigned int' [-Wformat=]
              left_len, sizeof(*phyerr));
                        ^
wmi.c: In function 'ath10k_wmi_10_4_op_pull_phyerr_ev':
wmi.c:3612:8: warning: format '%d' expects argument of type 'int',
	      but argument 4 has type 'long unsigned int' [-Wformat=]
              left_len, sizeof(*phyerr));
                        ^
Fixes: 991adf71 ("ath10k: refactor phyerr event handlers")
Fixes: 2b0a2e0d ("ath10k: handle 10.4 firmware phyerr event")
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This adds additional 0x0041 PCI Device ID
definition to ath10k for QCA6164 which is a 1
spatial stream sibling of the QCA6174 (which is 2
spatial stream chip).

The QCA6164 needs a dedicated board.bin file which
is different than the one used for QCA6174. If the
board.bin is wrong the device will crash early
while trying to boot firmware. The register dump
will look like this:

 ath10k_pci 0000:02:00.0: firmware register dump:
 ath10k_pci 0000:02:00.0: [00]: 0x05010000 0x000015B3 0x000A012D 0x00955B31
 ...

Note the value 0x000A012D.

Special credit goes to Alan Liu
<alanliu@qca.qualcomm.com> for providing support
help which enabled me to come up with this patch.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To enable/configure spectral scan parameters in 10.4 firmware, existing
wmi spectral related functions can be reused. Link those functions in
10.4 wmi ops table.

In addition, adjust bin size (only when size is 68 bytes) before reporting
bin samples to user space. The background for this adjustment is that
qca99x0 reports bin size as 68 bytes (64 bytes + 4 bytes) in report
mode 2. First 64 bytes carries in-band tones (-32 to +31) and last 4 byte
carries band edge detection data (+32) mainly used in radar detection
purpose. Additional last 4 bytes are stripped to make bin size valid one.

This bin size adjustment will happen only for qca99x0, all other chipsets
will report proper bin sizes (64/128) without extra 4 bytes being added
at the end. The changes are validated in qca99x0 using 10.4 firmware.
Signed-off-by: NRaja Mani <rmani@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function returns 1 when DMA mapping fails. The
driver would return bogus values and could
possibly confuse itself if DMA failed.

Fixes: 767d34fc ("ath10k: remove DMA mapping wrappers")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Kernel would complain about leaving a held lock
after going back to userspace and would
subsequently deadlock.

Fixes: e04cafbc ("ath10k: fix peer limit enforcement")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Florian Fainelli says:

====================
Documentation: dsa

This patch series adds some documentation about DSA as a subsystem as well
as the SF2 driver since it slightly diverges from your average DSA driver ;)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a document describing the Broadcom Starfigther 2 switch hardware,
its specifics, and how the driver is implemented and its specifics.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Describe how the DSA subsystem works, its design principles,
limitations, and describe in details how to implement a DSA switch
driver.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Santosh Shilimkar says:

====================
RDS: Few more fixes

As indicated in the earlier series [1], this is a follow-up series which
addresses few issues around the RDS FMR code. With [1] and the subject
series, now I can run many parallel threads with multiple sockets with
N x N traffic. The stress tests has survived overnight runs.

[1] https://lkml.org/lkml/2015/8/22/127
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory allocated for 'ibmr' uses kzalloc_node() which already
initialises the memory to zero. There is no need to do
memset() 0 on that memory.
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FMR flush is an expensive and time consuming operation. Reduce the
frequency of FMR pool flush by 50% so that more FMR work gets accumulated
for more efficient flushing.
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RDS FMR flush operation and also it races with connect/reconect
which happes a lot with RDS. FMR flush being on common rds_wq aggrevates
the problem. Lets push RDS FMR pool flush work to its own worker.
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In rds_ib_flush_mr_pool(), dirty_count accounts the clean ones
which is wrong. This can lead to a negative dirty count value.

Lets fix it.
Signed-off-by: NWengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds_rdma_unuse() drops the mr reference count which it hasn't
taken. Correct way of removing mr is to remove mr from the tree
and then rdma_destroy_mr() it first, then rds_mr_put() to decrement
its reference count. Whichever thread holds last reference will free
the mr via rds_mr_put()

This bug was triggering weird null pointer crashes. One if the trace
for it is captured below.

BUG: unable to handle kernel NULL pointer dereference at
0000000000000104
IP: [<ffffffffa0899471>] rds_ib_free_mr+0x31/0x130 [rds_rdma]
PGD 4366fa067 PUD 4366f9067 PMD 0
Oops: 0000 [#1] SMP

[...]

task: ffff88046da6a000 ti: ffff88046da6c000 task.ti: ffff88046da6c000
RIP: 0010:[<ffffffffa0899471>]  [<ffffffffa0899471>]
rds_ib_free_mr+0x31/0x130 [rds_rdma]
RSP: 0018:ffff88046fa43bd8  EFLAGS: 00010286
RAX: 0000000071d38b80 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff880079e7ff40
RBP: ffff88046fa43bf8 R08: 0000000000000000 R09: 0000000000000000
R10: ffff88046fa43ca8 R11: ffff88046a802ed8 R12: ffff880079e7fa40
R13: 0000000000000000 R14: ffff880079e7ff40 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff88046fa40000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000104 CR3: 00000004366fb000 CR4: 00000000000006e0
Stack:
 ffff880079e7fa40 ffff880671d38f08 ffff880079e7ff40 0000000000000296
 ffff88046fa43c28 ffffffffa087a38b ffff880079e7fa40 ffff880671d38f10
 0000000000000000 0000000000000292 ffff88046fa43c48 ffffffffa087a3b6
Call Trace:
 <IRQ>
 [<ffffffffa087a38b>] rds_destroy_mr+0x8b/0xa0 [rds]
 [<ffffffffa087a3b6>] __rds_put_mr_final+0x16/0x30 [rds]
 [<ffffffffa087a492>] rds_rdma_unuse+0xc2/0x120 [rds]
 [<ffffffffa08766d3>] rds_recv_incoming_exthdrs+0x83/0xa0 [rds]
 [<ffffffffa0876782>] rds_recv_incoming+0x92/0x200 [rds]
 [<ffffffffa0895269>] rds_ib_process_recv+0x259/0x320 [rds_rdma]
 [<ffffffffa08962a8>] rds_ib_recv_tasklet_fn+0x1a8/0x490 [rds_rdma]
 [<ffffffff810dcd78>] ? __remove_hrtimer+0x58/0x90
 [<ffffffff810799e1>] tasklet_action+0xb1/0xc0
 [<ffffffff81079b52>] __do_softirq+0xe2/0x290
 [<ffffffff81079df6>] irq_exit+0xa6/0xb0
 [<ffffffff81613915>] do_IRQ+0x65/0xf0
 [<ffffffff816118ab>] common_interrupt+0x6b/0x6b
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On rds_ib_frag_slab allocation failure, ensure rds_ib_incoming_slab
is not pointing to the detsroyed memory.
Signed-off-by: NSantosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Antonio Quartulli says:

====================
Included changes:
- code restyling and beautification
- use int kernel types instead of C99
- update kereldoc
- prevent potential hlist double deletion of VLAN objects
- fix gw bandwidth calculation
- convert list to hlist when needed
- add lockdep_asserts calls in function with lock requirements
  described in kerneldoc
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

posted_index is RO in firmware. We need not do ioread everytime to get
posted index. Store posted index locally.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>