When a station leaves suddenly while ampdu traffic to that station is still
running, there is a possibility that the ampdu pending queues are not freed due
to a race condition leading to memory leaks. In '__sta_info_destroy' when we
attempt to destroy the ampdu sessions in 'ieee80211_sta_tear_down_BA_sessions',
the driver calls 'ieee80211_stop_tx_ba_cb_irqsafe' to delete the ampdu
structures (tid_tx) and splice the pending queues and this job gets queued in
sdata workqueue. However, the sta entry can get destroyed before the above work
gets scheduled and hence the race.

Purging the queues and freeing the tid_tx to avoid the leak. The better solution
would be to fix the race, but that can be taken up in a separate patch.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We recently introduced a new return here but it needs an unlock first.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AP interfaces routinely call this logic, so just silently
return when this happens instead of splatting the kernel
logs.
Reported-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Arik's patch "mac80211: allow action frames with unknown
BSSID in GO mode" allowed any action frames in P2P mode
to go through, but only to cooked monitor interfaces as
the IEEE80211_RX_RA_MATCH was still cleared. As a result
my no-monitor patches broke invitation responses.

Instead of allowing any action frames in P2P GO mode to
go through with a wrong BSSID like that patch did, allow
all public action frames. They will never be processed
by mac80211, but can be reported via nl80211 then.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes another regression from my "pass all
fragments to driver at once" patches -- if the
packet is being retransmitted then we don't go
through all handlers, but we still need to move
it to the skbs list, otherwise we run into the
first warning in __ieee80211_tx() and leak the
skb.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.

If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.

If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.

Allow frame aggregation to start in IBSS mode.
Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit f785d83a.

This was provoking WARNINGs from the iwlegacy drivers.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The on-channel work optimisations have caused a
number of issues, and the code is unfortunately
very complex and almost impossible to follow.
Instead of attempting to put in more workarounds
let's just remove those optimisations, we can
work on them again later, after we change the
whole auth/assoc design.

This should fix rate_control_send_low() warnings,
see RH bug 731365.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The rates bitmap for internal scan requests shoud be filled,
otherwise there will be probe requests with zero rates supported.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There's little point in this config symbol, if
tracing is disabled the overhead is negligible
and if you think it's too bad you can always
turn off tracing completely.

Also remove the part where we don't have sparse
check the tracing code -- it seems that it can
now deal with it (or the code changed).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Lose about two levels of unnecessary indentation.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We used to initiate a path discovery when receiving a frame for which
there is no forwarding information. To cut down on PREQ spam, just send
a (gated) PERR in response.

Also separate path discovery logic from nexthop querying. This patch
means we no longer queue frames when forwarding, so kill the PERR TX
stuff in discard_frame().
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As per 802.11mb 13.9.11.3
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can't rely on ieee80211_select_queue() to do its job at this point
since the skb->protocol is not yet known. Instead, factor out and reuse
the queue mapping logic for injected frames.

Also, to mitigate congestion, forwarded frames should be dropped if the
outgoing queue was stopped.  This was not correctly implemented as we
were not checking the right queue.  Furthermore, we were dropping frames
that had arrived to their destination if that queue was stopped.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

HWMP originator and target addresses were switched on the air but also
on reception, which is why path selection still worked.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't write the TA until next hop is actually known, since we might need
the original TA for sending a PERR. Previously we would send a PERR to
ourself if path resolution for a forwarded frame failed.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It doesn't have any actual effect here, but we should
skb_put() *before* copying the data.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Emmanuel reported that my previous patches to enable
handing all fragments to drivers at once triggered
the warning that the SKB queue wasn't empty. This is
happening when we actually queue up some frames and
don't hand them to the driver (queues are stopped).

The reason for it is that my code that splices the
frame(s) over to the pending queue didn't re-init
the local queue, so skb_queue_empty() was false. Fix
this by using the _init versions of the splicing.

Also, convert the warning to WARN_ON_ONCE.
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes frequent WARN_ONs when using AP VLAN + aggregation, as these vifs
are virtual and not registered with drivers.
Use sta_info_get_bss instead of sta_info_get in aggregation callbacks, so
that these callbacks can find the station entry when called with the AP vif.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Add additional debug logging of initiator and reason when rx
aggregation session is stopped
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Use WLAN_BACK_RECIPIENT instead of hardcoded 0 for clarity
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

  Currently tx aggregation is not being timed out even if timeout is
specified when aggregation is opened. Tx tid stays active until delba
arrives from recipient (i.e. recipient times out tid when it is
inactive).
  The problem with this approach is that delba can get lost in the air
and tx tid will stay perpetually opened on the originator while closed
on recipient thus all data sent via this tid will be lost.
  This patch implements tx tid timeouting in way very similar to rx tid
timeouting.
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Due the a fall-through in the switch statement, the IBSS mode got a
report for AP_RPOBE_RESPONSE change on reconfig. Change this to an AP
only notification.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a sparse warning:

cfg.c:502:13: warning: incorrect type in assignment (different address spaces)
cfg.c:502:13:    expected struct sk_buff *old
cfg.c:502:13:    got struct sk_buff [noderef] <asn:4>*probe_resp
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch contains the processing changes in mac80211.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature has been superseded by the NoAck per Queue feature.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a packet is supposed to sent be as an a-MPDU, mac80211 sets
IEEE80211_TX_CTL_AMPDU to let the driver know. On the other
hand, mac80211 configures the driver for aggregration with the
ampdu_action callback.
There is race between these two mechanisms since the following
scenario can occur when the BA agreement is torn down:

Tx softIRQ	 			drv configuration
==========				=================

check OPERATIONAL bit
Set the TX_CTL_AMPDU bit in the packet

					clear OPERATIONAL bit
					stop Tx AGG
Pass Tx packet to the driver.

In that case the driver would get a packet with TX_CTL_AMPDU set
although it has already been notified that the BA session has been
torn down.

To fix this, we need to synchronize all the Qdisc activity after we
cleared the OPERATIONAL bit. After that step, all the following
packets will be buffered until the driver reports it is ready to get
new packets for this RA / TID. This buffering allows not to run into
another race that would send packets with TX_CTL_AMPDU unset while
the driver hasn't been requested to tear down the BA session yet.

This race occurs in practice and iwlwifi complains with a WARN_ON
when it happens.

Cc: stable@kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If addBA responses comes in just after addba_resp_timer has
expired mac80211 will still accept it and try to open the
aggregation session. This causes drivers to be confused and
in some cases even crash.

This patch fixes the race condition and makes sure that if
addba_resp_timer has expired addBA response is not longer
accepted and we do not try to open half-closed session.

Cc: stable@vger.kernel.org
Signed-off-by: NNikolay Martynov <mar.kolya@gmail.com>
[some adjustments]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Nikolay noticed (by code review) that mac80211 can
attempt to stop an aggregation session while it is
already being stopped. So to fix it, check whether
stop is already being done and bail out if so.

Also move setting the STOPPING state into the lock
so things are properly atomic.

Cc: stable@vger.kernel.org
Reported-by: NNikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sparse RCU checking reports two warnings in the mesh
path table code. These are due to questionable uses of
rcu_dereference.

To fix the first one, get rid of mesh_gate_add() and
just make mesh_path_add_gate() do the correct deref.

To fix the second one, simply remove rcu_dereference()
in mesh_gate_del() -- it already gets a proper pointer
as indicated by the prototype (no __rcu annotation)
and confirmed by the code.

Cc: Javier Cardona <javier@cozybit.com>
Cc: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This implements ht-cap over-rides for mac80211 drivers.
HT may be disabled, making an /a/b/g/n station act like an
a/b/g station.  HT40 may be disabled forcing the station to
be HT20 even if the AP and local hardware support HT40.

MAX-AMSDU may be disabled.
AMPDU-Density may be increased.
AMPDU-Factor may be decreased.

This has been successfully tested with ath9k using patched
wpa_supplicant and iw.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No other driver ever ended up using this, and
the commit forgot to move the prototype so no
driver could have used it. Revert it, if any
driver shows up and needs it it can be moved
again, but until then it's more efficient to
have it in mac80211 where the only user is.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently mac80211 implements these for all devices,
but given restrictions of some devices that isn't
really true, so prepare for being able to remove the
capability for some mac80211 devices.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

First time I tried smatch, and it says:
mesh_hwmp.c +870 mesh_queue_preq(21) error: double lock 'bottom_half:'
mesh_hwmp.c +873 mesh_queue_preq(24) error: double unlock 'bottom_half:'
mesh_hwmp.c +886 mesh_queue_preq(37) error: double unlock 'bottom_half:'

Which is indeed true -- there's no point in disabling BHs
again if we just did that a few lines earlier, so remove.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WLAN_STA_ASSOC_AP indicates that the station entry
is for an AP we're associated to but isn't used so
remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>