Received from Mark Salyzyn

If the adapter is in blinkled (Firmware Assert) when error recovery
timeout actions have been triggered, perform an adapter warm reset and
restart the initialization.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

The enclosed patch cleans up some code fragments, adds some paranoia
(unproven causes of potential driver failures).
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

If the adapter should be in a blinkled (Firmware Assert) state when the
driver loads, we will perform a warm restart of the Adapter Firmware to
see if we can rescue the adapter. Possible causes of a blinkled can
occur on some early release motherboard BIOSes, transitory PCI bus
problems on embedded systems or non-x86 based architectures, transitory
startup failures of early release drives or transitory hardware
failures; some of which can bite the adapter later at runtime. Future
enhancements will include recovery during runtime.

Fixed extra whitespace space issue.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

This patch allows the FSACTL_SEND_LARGE_FIB, FSACTL_SENDFIB and
FSACTL_SEND_RAW_SRB ioctl calls into the aacraid driver to be
interruptible. Only necessary if the adapter and/or the management
software has gone into some sort of misbehavior and the system is being
rebooted, thus permitting the user management software applications to
be killed relatively cleanly. The FIB queue resource is held out of the
free queue until the adapter finally, if ever, completes the command.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This may seem like a DILLIGAF, but after chatting with the F/W folks,
there is no harm in dropping the page calculation as denoted in the
enclosed patch for these older adapters in this new age of 4GB+ memory
sticks. Any resource optimization within the old-old-old adapters for
systems with less than 4G of memory is of little consequence. The
existing AAC_QUIRK_31BIT flag in linit.c should look after the rest of
the legacy hardware DMA limitations.
Signed-off-by: NMark Salyzyn <aacraid@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Rename the GART_IOMMU option to IOMMU to make clear it's not
   just for AMD
 - Rewrite the help text to better emphatise this fact
 - Make it an embedded option because too many people get it wrong.

To my astonishment I discovered the aacraid driver tests this
symbol directly. This looks quite broken to me - it's an internal
implementation detail of the PCI DMA API. Can the maintainer
please clarify what this test was intended to do?

Cc: linux-scsi@vger.kernel.org
Cc: alan@redhat.com
Cc: markh@osdl.org
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NEric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: N"Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Received from Mark Salyzyn

Spelling correction, orphaned comment removal & update branch name.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

Some of the cards product names changed.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

clear_user return is 0 for success, the code fragment is written to
assume that it is the count of the number of bytes zero'd.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions.  Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH.  Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

The queue tracking is just not being used, not even for debugging. Information
about outstanding commands can be acquired from the scsi structures.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

A race condition existed that could result in a lost completion of a
command to the ppc based cards.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

Add the ability to adjust for unusual corner case failures. Both of
these additional module parameters deal with embedded, non-intel or
complicated system scenarios.

Aif_timeout can be increased past the default 2 minute timeout to drop
application registrations when a system has an unusually high event load
resulting from continuing management requests, or simultaneous builds,
or sluggish user space as a result of system load.

Startup_timeout can be increased past the default 3 minute timeout to
drop an adapter initialization for systems that have a very large number
of targets, or slow to spin-up targets, or a complicated set of array
configurations that extend the time for the firmware to declare that it
is operational. This timeout would only have an affect on non-intel
based systems, as the (more patient) BIOS would generally be where the
startup delay would be dealt with.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

Slight space and speed efficiency improvement.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn

Since new commands to the card are quiesced, respect the changes in
the SCSI error path which dropped locking around the hba reset handler
and similarly drop the lock requirement in the driver's path.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Fix module param
Update driver version.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

On 64 bit machines, when a 32 bit application tries to acquire the AIF,
they will always get and EFAULT error response from the driver.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Add max_channel and max_id sysfs parameters.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Since the helper thread for the driver can be killed unceremoniously by
an application, we detect the loss of the helper and restart it.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Remove superfluous code, optimize code, harden code, cast code, correct
some text, use msleep instead of schedule_timeout_interruptible. No
bugs.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

If there are no aacraid controllers, we do not create the raid
controller chrdev, thus when the driver is unloaded it performs a
superfluous deregistration.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

The max_channel field is set one too large.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Some of the error return paths during initialization resulted in a zero
report to caller
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Plug and play actions resulting from event sequences shall time out if
they take longer than 30 seconds to complete.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

The loss of the ownership flags, despite their flaws, in the scsi
command were sorely missed and are reinstated more accurately in the
aacraid driver to track commands and permit us to properly handle error
recovery actions.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn

Clean up the remaining scsi id access methods, drop ID_LUN_TO_CONTAINER
macro.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Replace all occurences of 0xff..  in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: NMatthias Gehre <M.Gehre@gmx.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Use the kthread_ API instead of opencoding lots of hairy code for kernel
thread creation and teardown.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NSalyzyn, Mark <mark_salyzyn@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

asm/delay.h is non-portable; linux/delay.h should be used in generic code.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Received From Mark Salyzyn.

In order to support user tools accessing the array components (SMART,
Mode Page information, Cache page adjustments, WWN determination,
Firmware updates etc), we take advantage of the no_uld_attach flag and
deprecate the code that filters Inquiries to block the requests to array
components. The quirk prevents the sd layer from attaching to the
components.

We also took the opportunity to balance the queue depths based on the
total adapter queue depth to the array devices to reduce the chances of
starvation.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn,

Reduce the possibility of namespace collision.  Prefix with aac_.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn.

This patch sets up some device quirks surrounding arrays to inform the
scsi layer that various mode pages are not supported. This reduces the
severity of the complaints that show up in the logs as the array devices
are enumerated.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn.

Move the README from the driver directory to the Documentation directory.
Updated the documentation, added descriptions for cards that
were missing.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received From Mark Salyzyn.

The Jaguar and Corsair class of adapters (2410, 2810, 2610, 21610, CERC)
perform better (about 10% better read performance, write performance
neutral) with current Firmware if the OS limits the number of scatter
gather elements to 17 per request.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn.

Provide more accurate adapter information.

Allows the Adapter Firmware to override the Adapter product
information.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Received from Mark Salyzyn.

If the adapter has not instructed us otherwise that it can handle a
'large' FIB, then it can handle at most a 2KB FIB.
Signed-off-by: NMark Haverkamp <markh@osdl.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

These days ioctl32.h is only used for communication of fs/compat.c and
fs/compat_ioctl.c and doesn't contain anything of interest to drivers.

Remove inclusion in various drivers.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>