Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: NMarc Carino <marc.ceeeee@gmail.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Matt Porter <mporter@linaro.org>
Signed-off-by: NMatt Porter <mporter@linaro.org>

The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb, USB2.0 & 3.0,
powered by a Marvell Armada XP MV78230 dual core CPU.

http://shop.lenovo.com/us/en/servers/network-storage/lenovoemc/ix4-300d/Signed-off-by: NBenoit Masson <yahoo@perenite.com>
Link: https://lkml.kernel.org/r/1406503839-4662-1-git-send-email-yahoo@perenite.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This allows the "make dtbs" target to work.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

This allows to boot the Adapteva Parallella board to serial console.

Cc: Andreas Olofsson <andreas@adapteva.com>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This adds support for the A31 Hummingbird:
http://www.merrii.com/en/pla_d.asp?id=172

The Merrii A31 Hummingbird is a development board based on the
Allwinner A31 SoC with multiple USB ports through a USB hub chip,
a uSD slot, a 10/100/1000M ethernet port, an AP6210 WiFi/BT chip,
TV-in, HDMI, VGA, audio in/out ports, and LCD/CSI headers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: enable usbphy, ehci0, ohci0 for on-board usb hub;
 add pcf8563 rtc node; add comments for i2c0 and mmc0 pull-ups;
 correct ethernet phy address to 0x01; drop uart2 (BT chip has
 no power) and uart3 (no device); use proper commit message]
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

Add initial Rex Pro i.mx6dl board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working.  Currently no mainline u-boot, so boot with
cat zImage imx6dl-rex-basic.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial Rex Pro i.mx6q board support. Ethernet, UART, USB, I2C, SPI, HDMI,
Audio, and SDHC cards are working.  Currently no mainline u-boot, so boot with
cat zImage imx6q-rex-pro.dtb > zImage.dtb, then using mkimage create uImage
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The rev C1 Wandboard uses the Broadcom 4330 for WiFi and Bluetooth instead of
the 4329.  This changes the PADS assigned for the control lines.  Another
side effect of the change is that on the rev C1 board, usdhc driver can't
detect the chip presence correctly so usdhc2 now needs its 'non-removeable'
property removed.

So that rev B1 and earlier can continue to work, this patch splits the
board-specific definitions from imx6qdl-wandboard.dtsi into
imx6qdl-wandboard-revb1.dtsi and imx6qdl-wandboard-revc1.dtsi.  The new files
include the original base imx6qdl-wandboard.dtsi which retains the common
definitions.

The existing imx6dl-wandboard.dts includes imx6qdl-wandboard-revc1.dtsi and
imx6dl-wandboard-revb1.dts (new) includes imx6qdl-wandboard-revb1.dtsi.
This makes the rev C1 board the new default.  The same pattern is used for
imx6q-wandboard.dts.

So, from U-Boot on a WB-Quad you use imxq-wandboard-revb1.dtb for the older B1
board and imxq-wandboard.dtb for the current rev C1 board.
Signed-off-by: NGeorge Joseph <george.joseph@fairview5.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch add support for the imx6dl based aristainetos board
with following configuration:

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
DRAM:  1 GiB
NAND:  512 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB

As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

The CMO-QVGA, DVI-VGA and DVI-SVGA displays were added.
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

Add initial imx6sx-sdb board support with limited devices enabled.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

This patch adds the device tree to support Toradex Apalis T30, a
computer on module which can be used on different carrier boards.

The module consists of a Tegra 3 SoC, two PMICs, 1 or 2 GB of DDR3L
RAM, eMMC, an LM95245 temperature sensor chip, an i210 resp. i211
gigabit Ethernet controller, an STMPE811 ADC/touch controller as well
as two MCP2515 CAN controllers. Furthermore, there is an SGTL5000 audio
codec which is not yet supported. Anything that is not self contained
on the module is disabled by default.

The device tree for the Evaluation Board includes the modules device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).

While at it also add the device tree binding documentation for Apalis
T30.
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>
[swarren: fixed some node sort orders]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.

- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.orgSigned-off-by: NJason Cooper <jason@lakedaemon.net>

This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].

[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/Signed-off-by: NAsh Charles <ashcharles@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for TI's AM437x StarterKit Evaluation
Module.

Cc: Josh Elliot <jelliott@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NFranklin Cooper Jr. <fcooper@ti.com>
Tested-by: NTom Rini <trini@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ba10 tvbox is an A10 based android tvbox, with 512M RAM, 8G nand flash,
rtl8188ctv usb wifi 1 USB-A receptacle hooked up to an EHCI/OHCI controller,
1 USB-A receptacle hooked up to the OTG and 100Mbit ethernet using a
rtl8201 phy.

The PCB is labelled ba10 hence I've named the board ba10-tvbox. It is used
in noname allwinner A10 tv-boxes.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The LinkSprite pcDuino V3 is an A20 based development board featuring
arduino compatible io headers, 1G RAM, 4G nand, sata, rtl8188cus usb wifi
and 100 Mbit ethernet using an ip101a phy:

http://www.pcduino.com/pcduino-v3/Signed-off-by: NZoltan HERPAI <wigyori@uid0.hu>
[hdegoede@redhat.com: Various cleanups, correct led pins]
[hdegoede@redhat.com: Add axp209, ir and gpio-keys nodes]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets with A23 SoCs. There are at least 2 versions of the board, with
different peripherals, such as WiFi chips.

Common features among these tablets include 512 MB DRAM, NAND, MMC, LCD,
capacitive touchscreen, accelerometer, 1 or 2 camera sensors, USB OTG,
microphone and speaker.

v5 of these board designs has a ESP8089 WiFi chip (not supported)
connected to mmc1. This patch adds very basic support.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

As Mainlining effort for SolidRun CuBox has been carried out on the
Engineering Sample, the board DTS was reflecting this. Actually,
SolidRun CuBox comes in three different variants:
Engineering Sample (ES), production with 1GB RAM (1G),
and production with 2GB RAM (2G).

Therefore, we base current dove-cubox.dts on to the 1G production
variant and add a ES dts to add required quirk for misrouted SDHCI
card detect on top of dove-cubox.dts. For the 2G variant we rely on
the bootloader to setup correct RAM size.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1401228006-3212-1-git-send-email-sebastian.hesselbarth@gmail.comSigned-off-by: NJason Cooper <jason@lakedaemon.net>

Describe LaCie 2Big and 5Big Network v2 using device tree.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1401132591-26305-3-git-send-email-andrew@lunn.chAcked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Two reasons for this rename.  Firstly, it removes the camel case
convention which isn't used by any other platform and secondly it
matches the naming convention for the internal kernel, which can
become annoying when flipping between the two.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board.
Signed-off-by: NTarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: NVyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Adds support for google peach-pi board having the
Exynos5800 SoC.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The patch adds the dts file for xyref5260 board which
is based on exynos5260 SoC.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add device-tree file for APQ8084-MTP board, which belongs
to the Snapdragon 805 family.
Signed-off-by: NGeorgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add basic APQ8064 SoC include device tree and support for basic booting on
the IFC6410 board.  Also, keep dtb build list and qcom_dt_match in sorted
order.
Signed-off-by: NKumar Gala <galak@codeaurora.org>

Add device tree for the Amarillo validation board with an AXM5516 SoC.
Signed-off-by: NAnders Berg <anders.berg@lsi.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The i12 tvbox is an A20 based android tvbox, with 512M / 1G RAM, 4G nand flash,
ap6210 or ap6330 sdio wifi + bt (broadcom sdio wifi + uart attached brcm bt),
2USB host ports using USB-A receptacles and a micro-usb receptacle for USB OTG,
and 100Mbit ethernet using an IP101a phy.

The PCB is labelled i12-a20 hence I've named the board i12-a20. It is used
in noname allwinner A20 tv-boxes, which are sometimes sold with Q5 or
QT840A as product name.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The B2020 RevE differs from the other B2020 boards in a few subtle ways;
including the Ethernet reset GPIO which this patch adds support for and
the LED wiring which will follow in a latter patch.  Without supplying
these differences Ethernet and the board LEDs simply will not work.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

B2120 HDK is the reference board for STiH407 SoC.
It has the following characteristics:
 - 1GB DDR3
 - 8GB eMMC / SD-Card slot
 - 32MB NOR Flash
 - 1 x Gbit Ethernet
 - 1 x USB 3.0 port
 - 1 x Mini-PCIe
 - 1 x SATA
 - 1 x HDMI output
 - 1 x HDMI input
 - 1 x SPDIF

This patch only introduces basic functionnalities, such as I2C and UART.
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

The boards have to be sorted in alphanumerical order in the Makefile.

Cc: Olof Johansson <olof@lixom.net>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMaxime Coquelin <maxime.coquelin@st.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for VAR-SOM-OM44[1] SODIMM system on module from
Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet
(LAN7500) and optional WLAN/BT.

Also add support for VAR-STK-OM44 development board from
Variscite. This kit features a VAR-SOM-OM44 and the carrier board
VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as
VAR-DVK-OM44 but without the LCD display.

omap4-var-stk-om44.dts replace the old and very limited
omap4-var-som.dts.

[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboardSigned-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds initial support for the Marvell BG2-Q DMP. The board has 2GB of
memory, an uart activated and what's initially supported by the Marvell
Armada 1500 pro dtsi.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Allwinner sunxi support has been split into the various SoCs in Kconfig.
Adapt the new symbols for the device trees.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Let the multiplatform Genmai support boot with the unified DTS.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Now that r7s72100 has CCF support, remove the legacy Genmai reference
Kconfig bits for the non-multiplatform case.

Starting from this commit Genmai board support is always enabled via
CONFIG_MACH_GENMAI, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-genmai.c and board-genmai-reference.c

The file board-genmai-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>