Now that most of the special Bay- / Cherry-Trail bus lock handling has
been moved to the iosf_mbi code we can simplify the remaining code a bit.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.

After commit 12864ff8 ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).

On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.

The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.

But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.

The _PS3 method for this I2C controller looks like this:

            Method (_PS3, 0, NotSerialized)  // _PS3: Power State 3
            {
                If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
                {
                    Return (Zero)
                }

                PSAT |= 0x03
                Local0 = PSAT /* \_SB_.I2C5.PSAT */
            }

Where PMID = 0x05, so we enter the Return (Zero) path on these systems.

So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.

Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.

Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.

This commit implements this fix by:

1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.

2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.

Fixes: 12864ff8 ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Replace short statement in comment with proper SPDX license tag.

Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: NLuis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Instead of using custom variables and parser, convert the driver to use
the ones provided by I2C core.

No functional change intended.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Optimize the power management in i2c-designware-platdrv by making it
set the DPM_FLAG_SMART_SUSPEND and DPM_FLAG_LEAVE_SUSPENDED which
allows some code to be dropped from its PM callbacks.

First, setting DPM_FLAG_SMART_SUSPEND causes the intel-lpss driver
to avoid resuming i2c-designware-platdrv devices in its ->prepare
callback, so they can stay in runtime suspend after that point even
if the direct-complete feature is not used for them.

It also causes the ACPI PM domain and the PM core to avoid invoking
"late" and "noirq" suspend callbacks for these devices if they are
in runtime suspend at the beginning of the "late" phase of device
suspend during system suspend.  That guarantees dw_i2c_plat_suspend()
to be called for a device only if it is not in runtime suspend.

Moreover, it causes the device's runtime PM status to be set to
"active" after calling dw_i2c_plat_resume() for it, so the
driver doesn't need internal flags to avoid invoking either
dw_i2c_plat_suspend() or dw_i2c_plat_resume() twice in a row.

Second, setting DPM_FLAG_LEAVE_SUSPENDED enables the optimization
allowing the device to stay suspended after system resume under
suitable conditions, so again the driver doesn't need to take
care of that by itself.

Accordingly, the internal "suspended" and "skip_resume" flags
used by the driver are not necessary any more, so drop them and
simplify the driver's PM callbacks.

Additionally, notice that dw_i2c_plat_complete() only needs to
schedule runtime PM resume for the device if platform firmware
has been involved in resuming the system, so make it call
pm_resume_via_firmware() to check that.  Also make it check the
runtime PM status of the device instead of its direct_complete
flag which also works if the device remained suspended due to
the DPM_FLAG_LEAVE_SUSPENDED driver flag.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>

Modify i2c-designware-platdrv to set DPM_FLAG_SMART_PREPARE for its
devices and return 0 from the system suspend ->prepare callback
if the device has an ACPI companion object in order to tell the PM
core and middle layers to avoid skipping system suspend/resume
callbacks for the device in that case (which may be problematic,
because the device may be accessed during suspend and resume of
other devices via I2C operation regions then).

Also the pm_runtime_suspended() check in dw_i2c_plat_prepare()
is not necessary any more, because the core does it when setting
power.direct_complete for the device, so drop it.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>

For consistency with the rest of the file rename function and parameter to
be consistent with the reset of the common file.
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Move the i2c_dw_plat_prepare_clk funciton to common file in preparation
for its use also by the master driver.
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to data sheet SCL timing parameters and DW_IC_CON SPEED mode
bits are not used when operating in slave mode.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NLuis Oliveira <lolivei@synopsys.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Don't populate const array supported_speeds on the stack, instead
make it static.  Makes the object code smaller by 150 bytes:

Before:
   text	   data	    bss	    dec	    hex	filename
   8474	   1440	      0	   9914	   26ba	i2c-designware-platdrv.o

After:
   text	   data	    bss	    dec	    hex	filename
   8324	   1440	      0	   9764	   2624	i2c-designware-platdrv.o

(gcc version 7.2.0 x86_64)
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

As reported by Rajat Jain, there are problems when ACPI operation
region handlers or similar, called at the ->resume_early() time, for
I2C client devices try to access an I2C controller that has already
been suspended at that point.  To avoid that, move the suspend/resume
of i2c-designware-platdrv to the late/early stages, respectively.

While at it, avoid resuming the device from runtime suspend in the
driver's ->suspend callback which isn't particularly nice.  [A better
approach would be to make the driver track the PM state of the device
so that it doesn't need to resume it in ->suspend, so implement it.]

First, drop dw_i2c_plat_suspend() added by commit a23318fe (i2c:
designware: Fix system suspend) and rename dw_i2c_plat_runtime_suspend()
back to dw_i2c_plat_suspend().

Second, point the driver's ->late_suspend and ->early_resume
callbacks, rather than its ->suspend and ->resume callbacks,
to dw_i2c_plat_suspend() and dw_i2c_plat_resume(), respectively,
so that they are not executed in parallel with each other, for
example if runtime resume of the device takes place during system
suspend.

Finally, add "suspended" and "skip_resume" flags to struct dw_i2c_dev
and make dw_i2c_plat_suspend() and dw_i2c_plat_resume() use them to
avoid suspending or resuming the device twice in a row and to avoid
resuming a previously runtime-suspended device during system resume.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: NJohannes Stezenbach <js@sig21.net>
Tested-by: NRajat Jain <rajatja@google.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The power management handling in dw_i2c_plat_probe() is somewhat
messy and it is rather hard to figure out the code intention for
the case when pm_disabled is set.  In that case, the driver doesn't
enable runtime PM at all, but in addition to that it calls
pm_runtime_forbid() as though it wasn't sure if runtime PM might
be enabled for the device later by someone else.

Although that concern doesn't seem to be actually valid, the
device is clearly still expected to be PM-capable even in the
pm_disabled set case, so a better approach would be to enable
runtime PM for it unconditionally and prevent it from being
runtime-suspended by using pm_runtime_get_noresume().

Make the driver do that.
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The Lenovo Miix2 8 DSDT contains an i2c clk / bus speed of 1700000 Hz
for one if its devices, which is not supported.

This is the second DSDT to show up with an unsupported clk in a short
time, remove the hardcoded fix for DSDTs with a 1 MiHz clock and simply
always round down the clk to the nearest supported value.

Reported-by: russianneuromancer@ya.ru
Fixes: 682c6c21 ("i2c: designware: Some broken DSTDs use 1MiHz ...")
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Code sets bit DW_IC_CON_SPEED_FAST (0x4) always when configuring the slave
mode. This results incorrect register value DW_IC_CON_SPEED_HIGH (0x6)
when OR'ed together with DW_IC_CON_SPEED_STD (0x2).

Remove this and let the code set the speed mode bits according to clock
frequency or default to fast mode.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The commit 8503ff16 ("i2c: designware: Avoid unnecessary resuming
during system suspend"), may suggest to the PM core to try out the so
called direct_complete path for system sleep. In this path, the PM core
treats a runtime suspended device as it's already in a proper low power
state for system sleep, which makes it skip calling the system sleep
callbacks for the device, except for the ->prepare() and the ->complete()
callbacks.

However, the PM core may unset the direct_complete flag for a parent
device, in case its child device are being system suspended before. In this
scenario, the PM core invokes the system sleep callbacks, no matter if the
device is runtime suspended or not.

Particularly in cases of an existing i2c slave device, the above path is
triggered, which breaks the assumption that the i2c device is always
runtime resumed whenever the dw_i2c_plat_suspend() is being called.

More precisely, dw_i2c_plat_suspend() calls clk_core_disable() and
clk_core_unprepare(), for an already disabled/unprepared clock, leading to
a splat in the log about clocks calls being wrongly balanced and breaking
system sleep.

To still allow the direct_complete path in cases when it's possible, but
also to keep the fix simple, let's runtime resume the i2c device in the
->suspend() callback, before continuing to put the device into low power
state.

Note, in cases when the i2c device is attached to the ACPI PM domain, this
problem doesn't occur, because ACPI's ->suspend() callback, assigned to
acpi_subsys_suspend(), already calls pm_runtime_resume() for the device.

It should also be noted that this change does not fix commit 8503ff16
("i2c: designware: Avoid unnecessary resuming during system suspend").
Because for the non-ACPI case, the system sleep support was already broken
prior that point.

Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Several drivers call to_platform_device() to get platform_device
and pass it to platform_get_drvdata().  In platform_get_drvdata(),
the platform_device is converted back to struct device again.

Use dev_get_drvdata() to avoid platform_device/device dance.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> (for DesignWare only)
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

At least the Acer Iconia Tab8 / aka W1-810 uses 1MiHz instead of
1MHz for one of its busses, fix this up to 1MHz instead of failing
the probe of that bus.

This fixes the accelerometer on the Acer Iconia Tab8 not working.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

When we refuse to probe due to an invalid clock frequency, log
the frequency which is causing this error.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

- Slave mode selected in platform module if the support is detected in
  the DT.
Signed-off-by: NLuis Oliveira <lolivei@synopsys.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

- The functions related to I2C master mode of operation were transformed
  in a single driver.
- Common definitions were moved to i2c-designware-core.h
- The i2c-designware-core is now only a library file, the functions
  associated are in a source file called i2c-designware-common and
  are used by both i2c-designware-master and i2c-designware-slave.
- To decrease noise in namespace common i2c_dw_*() functions are
  now using ops to keep them private.
- Designware PCI driver had to be changed to match the previous ops
  functions implementation.

Almost all of the "core" source is now part of the "master" source. The
difference is the functions used by both modes and they are in the
"common" source file.
Signed-off-by: NLuis Oliveira <lolivei@synopsys.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

- Factor out all _master() part of code from i2c-designware-core
  and i2c-designware-platdrv to separate functions.
- Standardize all code related with MASTER mode.
- I have to take off DW_IC_INTR_TX_EMPTY from DW_IC_INTR_DEFAULT_MASK
  because it is master specific.

The purpose of this is to prepare the controller to have is I2C MASTER
flow in a separate driver. To do this first all the
functions/definitions related to the MASTER flow were identified.
Signed-off-by: NLuis Oliveira <lolivei@synopsys.com>
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The purpose of this commit is to fix some comments and styling in the
existing code due to the need of reuse this code. What is being made
here is:

- Sorted the headers files
- Corrected some comments style (capital letters, lowcase i2c)
- Reverse tree in the variables declaration
- Add/remove empty lines and tabs where needed
- Fix of misspelled word "endianness" and "transferred"
- Replaced the return variable "r" with the more standard "ret"

The value of this, besides the rules of coding style, is because I
will use this code after and it will make my future patch a lot bigger and
complicated to review. The work here won't bring any additional work to
backported fixes because is just style and reordering.
Signed-off-by: NLuis Oliveira <lolivei@synopsys.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.
Reported-and-tested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Reported-by: NTobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Fixes: 9d640843 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We need to initializes those variables to 0 for platforms that do not
provide ACPI parameters. Otherwise, we set sda_hold_time to random
values, breaking e.g. Galileo and IOT2000 boards.

Fixes: 9d640843 ("i2c: designware: don't infer timings described by ACPI from clock rate")
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Commit bd698d24 ("i2c: designware: Get selected speed mode
sda-hold-time via ACPI") updated the logic that reads the timing
parameters for various I2C bus rates from the DSDT, to only read
the timing parameters for the currently selected mode.

This causes a WARN_ON() splat on platforms that legally omit the clock
frequency from the ACPI description, because in the new situation, the
core I2C designware driver still accesses the fields in the driver
struct that we no longer populate, and proceeds to calculate them from
the clock frequency. Since the clock frequency is unspecified, the
driver complains loudly using a WARN_ON().

So revert back to the old situation, where the struct fields for all
timings are populated, but retain the new logic which chooses the SDA
hold time from the timing mode that is currently in use.

Fixes: bd698d24 ("i2c: designware: Get selected speed mode ...")
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reported-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add ACPI HID HISI02A1 and HISI02A2 for Hisilicon Hip07/08,
which have different clock frequency.
Signed-off-by: NHanjun Guo <hanjun.guo@linaro.org>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Sda-hold-time is an important parameter for tuning i2c to meet the
electrical specification especially for high speed. I2C with incorrect
sda-hold-time may cause lost arbitration error. Instead of loading all
speed mode settings, only selected speed mode settings are loaded.
Signed-off-by: NTan Chin Yew <chin.yew.tan@intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Cherrytrail devices use the dw i2c-bus with uid 7 to access their PMIC.
Even if the i2c-bus to the PMIC is not shared with the SoC's P-Unit
and i2c-designware-baytrail.c thus does not set the pm_disabled flag,
we still need to disable pm so that ACPI PMIC opregions can access the
PMIC during late-suspend and early-resume.

This fixes errors like these blocking suspend:

  i2c_designware 808622C1:06: timeout waiting for bus ready
  ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
  acpi 80860F14:02: Failed to change power state to D3hot
  PM: late suspend of devices failed
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Currently we are already setting a pm_runtime_disabled flag and disabling
runtime-pm for i2c-busses used for accessing the system PMIC on x86.
But this is not enough, there are ACPI opregions which may want to access
the PMIC during late-suspend and early-resume, so we need to completely
disable pm to be safe.

This commit renames the flag from pm_runtime_disabled to pm_disabled and
adds the following new behavior if the flag is set:

1) Call dev_pm_syscore_device(dev, true) which disables normal suspend /
   resume and remove the pm_runtime_disabled check from dw_i2c_plat_resume
   since that will now never get called. This fixes suspend_late handlers
   which use ACPI PMIC opregions causing errors like these:

  PM: Suspending system (freeze)
  PM: suspend of devices complete after 1127.751 msecs
  i2c_designware 808622C1:06: timeout waiting for bus ready
  ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
  acpi 80860F14:02: Failed to change power state to D3hot
  PM: late suspend of devices failed

2) Set IRQF_NO_SUSPEND irq flag. This fixes resume_early handlers which
   handlers which use ACPI PMIC opregions causing errors like these:

  PM: resume from suspend-to-idle
  i2c_designware 808622C1:06: controller timed out
  ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Some platforms like hi3660 need do reset first to allow accessing registers
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: NRamiro Oliveira <ramiro.oliveira@synopsys.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The cherrytrail punit has the pmic i2c bus access semaphore at a
different register address.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-9-hdegoede@redhat.com

On my cherrytrail tablet with axp288 pmic, just doing a bunch of repeated
reads from the pmic, e.g. "i2cdump -y 14 0x34" would lookup the tablet in
1 - 3 runs guaranteed.

This seems to be causes by the cpu trying to enter C6 or C7 while we hold
the punit bus semaphore, at which point everything just hangs.

Avoid this by disallowing the CPU to enter C6 or C7 before acquiring the
punit bus semaphore.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109051Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-7-hdegoede@redhat.com

Rename accessor_flags to flags, so that we can use the field for
other flags too. This is a preparation patch for adding cherrytrail
support to the punit semaphore code.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-4-hdegoede@redhat.com

ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.
Signed-off-by: NTin Huynh <tnhuynh@apm.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Use a common place for default functionality bits for both platform
and pci driver.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Allow more flexibility to bus speed selection. Now if there are I2C
slave connections defined in ACPI the speed of slowest device on the bus
will define the bus speed. However if also "clock-frequency" device
property is defined we should use the slowest of these two.

This is targeted to maker boards where developer may want to connect
slower I2C slave devices to the bus than defined in existing ACPI I2C
slave connections.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Signed-off-by: NTin Huynh <tnhuynh@apm.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Fast mode is the default speed of i2c-designware which can be overridden
by platform data or by "clock-frequency" device property. Even though
the ACPI 5.1 can pass device properties via _DSD method, shipping systems
define the connection speed between I2C host and each slave in their
I2cSerialBus resources. Which means speed is not defined per bus but per
slave.

As there is now support in i2c-core to find the bus speed from ACPI use
that to set up the bus speed prior registering the I2C adapter.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This patch enabled high speed mode. High speed mode can be turn on by
setting the clk_freq to 3400000. High speed HCNT and LCNT are needed
as there is no default value provided.
Signed-off-by: NWeifeng Voon <weifeng.voon@intel.com>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

DW_IC_CON_MASTER, DW_IC_CON_SLAVE_DISABLE and DW_IC_CON_RESTART_EN are
common config that need to be set for i2c designware master. So, configure
it first without having to repeat inside the if else.
Signed-off-by: NWeifeng Voon <weifeng.voon@intel.com>
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>