i2c: designware: Implement support for SMBus block read and write

Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Signed-off-by: NTin Huynh <tnhuynh@apm.com>
Acked-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

drivers/i2c/busses/i2c-designware-core.c

@@ -554,6 +554,8 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 	intr_mask = DW_IC_INTR_DEFAULT_MASK;
 
 	for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) {
+		u32 flags = msgs[dev->msg_write_idx].flags;
+
 		/*
 		 * if target address has changed, we need to
 		 * reprogram the target address in the i2c
@@ -599,8 +601,15 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 			 * detected from the registers so we set it always
 			 * when writing/reading the last byte.
 			 */
+
+			/*
+			 * i2c-core.c always sets the buffer length of
+			 * I2C_FUNC_SMBUS_BLOCK_DATA to 1. The length will
+			 * be adjusted when receiving the first byte.
+			 * Thus we can't stop the transaction here.
+			 */
 			if (dev->msg_write_idx == dev->msgs_num - 1 &&
-			    buf_len == 1)
+			    buf_len == 1 && !(flags & I2C_M_RECV_LEN))
 				cmd |= BIT(9);
 
 			if (need_restart) {
@@ -625,7 +634,12 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 		dev->tx_buf = buf;
 		dev->tx_buf_len = buf_len;
 
-		if (buf_len > 0) {
+		/*
+		 * Because we don't know the buffer length in the
+		 * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop
+		 * the transaction here.
+		 */
+		if (buf_len > 0 || flags & I2C_M_RECV_LEN) {
 			/* more bytes to be written */
 			dev->status |= STATUS_WRITE_IN_PROGRESS;
 			break;
@@ -646,6 +660,24 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev)
 	dw_writel(dev, intr_mask,  DW_IC_INTR_MASK);
 }
 
+static u8
+i2c_dw_recv_len(struct dw_i2c_dev *dev, u8 len)
+{
+	struct i2c_msg *msgs = dev->msgs;
+	u32 flags = msgs[dev->msg_read_idx].flags;
+
+	/*
+	 * Adjust the buffer length and mask the flag
+	 * after receiving the first byte.
+	 */
+	len += (flags & I2C_CLIENT_PEC) ? 2 : 1;
+	dev->tx_buf_len = len - min_t(u8, len, dev->rx_outstanding);
+	msgs[dev->msg_read_idx].len = len;
+	msgs[dev->msg_read_idx].flags &= ~I2C_M_RECV_LEN;
+
+	return len;
+}
+
 static void
 i2c_dw_read(struct dw_i2c_dev *dev)
 {
@@ -670,7 +702,15 @@ i2c_dw_read(struct dw_i2c_dev *dev)
 		rx_valid = dw_readl(dev, DW_IC_RXFLR);
 
 		for (; len > 0 && rx_valid > 0; len--, rx_valid--) {
-			*buf++ = dw_readl(dev, DW_IC_DATA_CMD);
+			u32 flags = msgs[dev->msg_read_idx].flags;
+
+			*buf = dw_readl(dev, DW_IC_DATA_CMD);
+			/* Ensure length byte is a valid value */
+			if (flags & I2C_M_RECV_LEN &&
+				*buf <= I2C_SMBUS_BLOCK_MAX && *buf > 0) {
+				len = i2c_dw_recv_len(dev, *buf);
+			}
+			buf++;
 			dev->rx_outstanding--;
 		}
 

drivers/i2c/busses/i2c-designware-pcidrv.c

@@ -75,6 +75,7 @@ struct dw_pci_controller {
 					I2C_FUNC_SMBUS_BYTE |		\
 					I2C_FUNC_SMBUS_BYTE_DATA |	\
 					I2C_FUNC_SMBUS_WORD_DATA |	\
+					I2C_FUNC_SMBUS_BLOCK_DATA |	\
 					I2C_FUNC_SMBUS_I2C_BLOCK)
 
 /* Merrifield HCNT/LCNT/SDA hold time */

drivers/i2c/busses/i2c-designware-platdrv.c

@@ -220,6 +220,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 		I2C_FUNC_SMBUS_BYTE |
 		I2C_FUNC_SMBUS_BYTE_DATA |
 		I2C_FUNC_SMBUS_WORD_DATA |
+		I2C_FUNC_SMBUS_BLOCK_DATA |
 		I2C_FUNC_SMBUS_I2C_BLOCK;
 
 	dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE |