One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds a small bit of missing code for enabling the overheat sensor
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_up and ixgbe_up_complete will always return 0.  Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes a minor redundancy in that tx_sample_rate was set twice.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Private rx_csum flags are now duplicate of netdev->features & NETIF_F_RXCSUM.
Removing this needs deeper surgery.

Things noticed:
 - ixgb has RX csum disabled by default
 - HW VLAN acceleration probably can be toggled, but it's left as is
 - the resets on RX csum offload change can probably be avoided
 - there is A LOT of copy-and-pasted code here
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This reverts commit 0856a304.

As requested by Eric Dumazet, it has various ref-counting
problems and has introduced regressions.  Eric will add
a more suitable version of this performance fix.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer.  If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.

If it's too small, the return value will be -EMSGSIZE.  But if it's
too large, there is no indication of this.  Fix this by updating
the rule_cnt field on return.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.

Add note that drivers must not use ethtool_rxnfc::rule_locs.

The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The location of an RX flow classification rule is needed to identify
it for retrieval, replacement or deletion.  However it also defines
the priority of the rule in the case that a flow is matched by
multiple rules.  This is what I intended to imply by referring to the
use of a TCAM, commonly used to implement that behaviour.

However there are other ways this can be done, and it is better to
specify this explicitly.  Further, I want to add the option for
automatic selection of rule locations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refer consistently to 'classification rules' or just 'rules' rather
than 'filter specifications' or 'filter rules'.

Refer consistently to rule 'locations' and not 'indices'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All tables of function pointers should be const.
The pre-existing code has lots of needless indirection...

Inspired by similar change in PAX.
Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To prevent malicious usage, all tables of pointers must be const.

Compile tested only.
Gleaned for PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function tables need to be const to prevent malicious use.

This is compile tested only.
Gleaned from PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is compile tested only.
Suggested by dumpster diving in PAX.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch improves the logic determining when to send ICMPv6 Router
Solicitations, so that they are 1) always sent when the kernel is
accepting Router Advertisements, and 2) never sent when the kernel is
not accepting RAs. In other words, the operational setting of the
"accept_ra" sysctl is used.

The change also makes the special "Hybrid Router" forwarding mode
("forwarding" sysctl set to 2) operate exactly the same as the standard
Router mode (forwarding=1). The only difference between the two was
that RSes was being sent in the Hybrid Router mode only. The sysctl
documentation describing the special Hybrid Router mode has therefore
been removed.

Rationale for the change:

Currently, the value of forwarding sysctl is the only thing determining
whether or not to send RSes. If it has the value 0 or 2, they are sent,
otherwise they are not. This leads to inconsistent behaviour in the
following cases:

* accept_ra=0, forwarding=0
* accept_ra=0, forwarding=2
* accept_ra=1, forwarding=2
* accept_ra=2, forwarding=1

In the first three cases, the kernel will send RSes, even though it will
not accept any RAs received in reply. In the last case, it will not send
any RSes, even though it will accept and process any RAs received. (Most
routers will send unsolicited RAs periodically, so suppressing RSes in
the last case will merely delay auto-configuration, not prevent it.)

Also, it is my opinion that having the forwarding sysctl control RS
sending behaviour (completely independent of whether RAs are being
accepted or not) is simply not what most users would intuitively expect
to be the case.
Signed-off-by: NTore Anderson <tore@fud.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a CAN Gateway/Router to route (and modify) CAN frames.

It is based on the PF_CAN core infrastructure for msg filtering and msg
sending and can optionally modify routed CAN frames on the fly.
CAN frames can *only* be routed between CAN network interfaces (one hop).
They can be modified with AND/OR/XOR/SET operations as configured by the
netlink configuration interface known e.g. from iptables. From the netlink
view this can-gw implements RTM_{NEW|DEL|GET}ROUTE for PF_CAN.

The CAN specific userspace tool to manage CAN routing entries can be found in
the CAN utils http://svn.berlios.de/wsvn/socketcan/trunk/can-utils/cangw.c
at the SocketCAN SVN on BerliOS.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An earlier developer misunderstood the meaning of the 'irq' fields and
the driver did not support the standard fields.  To avoid invalidating
existing user documentation, we report and accept changes through
either the standard or 'irq' fields.  If both are changed at the same
time, we prefer the standard field.

Also explain why we don't currently use the 'max_frames' fields.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a range check, and move the check that RX and TX are consistent
from efx_ethtool_set_coalesce().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reported TX IRQ moderation is generated in a completely crazy way.
Make it simple and correct.

When channels are shared between RX and TX, TX IRQ moderation must be
the same as RX IRQ moderation, but must be specified as 0!  Allow it
to be either specified as the same, or left at its previous value
in which case it will be quietly overridden.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It was possible to inadvertently add additional interrupt causes to the
MSI-X other interrupt.  This occurred when things such as RX buffer overrun
events were being triggered at the same time as an event such as a Flow
Director table reinit request.  In order to avoid this we should be
explicitly programming only the interrupts that we want enabled.  In
addition I am renaming the ixgbe_msix_lsc function and interrupt to drop
any implied meaning of this being a link status only interrupt.

Unfortunately the patch is a bit ugly due to the fact that ixgbe_irq_enable
needed to be moved up before ixgbe_msix_other in order to have things
defined in the correct order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to cleanup some of the code related to SR-IOV and the
interrupt registers.  Specifically I am moving the EITRSEL configuration
into the MSI-X configuration section instead of enablement.  Also I am
fixing the VF shutdown path since it had operations in the incorrect order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The reset paths are overly complicated and are either missing steps or
contain extra unnecessary steps such as reading MAC address twice.  This
change is meant to help clean up the reset paths an get things functioning
correctly.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updated the TXDCTL configuration.  The main goal is to be much
more explicit about the configuration and avoid a possible fake TX hang
when the interrupt throttle rate is set to 0.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a minor whitespace cleanup to compress the device ID
declaration and board type declaration onto the same line.  It seems to
make sense since all of the combinations of the two are less than 80
characters and it makes the overall layout a bit more readable.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch drops a set of unnecessary dereferences to the hardware structure
since we already have a local copy of the hardware pointer.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that the map_rings_to_vectors call will work with
all interrupt types.  The advantage to this is that there will now be a
predictable mapping for all given interrupt types.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change switches us over to using the ring->dev pointer instead of
having to use the adapter->pdev->dev reference.  The advantage to this is
that it is a much shorter route to get the to final needed value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The allocation and freeing of the IRQ affinity hint needs some updates
since there are a number of spots where we run into possible issues with
the hint not being correctly updated.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change consolidates all of the MSI-X interrupt and polling routines
into two single functions.  One for the interrupt and one for the code.
The main advantage to doing this is that the compiler can optimize the
routines into single monolithic functions which should allow all of them
function to occupy a single block of memory and as such avoid jumping
around.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the default Tx work limit is 256 buffers or
1/2 of an entire ring instead of a full ring size so that it is much more
likely that we will be able to actually reach the work limit value.
Previously with the value set to an entire ring it would not have been
possible for us to trigger an event due to the fact that the Tx work is
stopped at the point where we cannot place one more buffer on the ring and
it is not restarted until cleanup is complete.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
  from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
  iboe_get_rate was previously ->get_settings() called unlocked. This
  fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
  problem. Also fixed by calling __dev_get_by_index() instead of
  dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
  so bnx2fc_if_create() and fcoe_if_create() are called locked as they
  are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: NJiri Pirko <jpirko@redhat.com>

v2->v3:
	-removed dev_ethtool_get_settings()
	-added ASSERT_RTNL into __ethtool_get_settings()
	-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
	 around it and __ethtool_get_settings() call
v1->v2:
        add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

it also cleanup white space
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>