UART2 is used to connect the processor with the bluetooth chip, these pins
are not common between IGEPv2 boards and IGEP COM MODULE boards. This patch
muxes the correct pins for every board and removes UART2 configuration from
common omap3-igep.dtsi file.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NJavier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

by adding labels to DWC3 nodes, it's far easier
for boards to reference them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for otg 4 move to dra74x.dtsi]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA7 Data Manual (SPRS857L - August 2014) section 4.1.1 states: "All
unused power supply balls must be supplied with the voltages specified
in the Section 5.2, Recommended Operating Conditions".

This implies that all unused voltage rails for Vayu can never be
switched off even if the hardware blocks inside that voltage domain is
unused. Switching off these unused rails may result in stability issues
on other domains and increased leakage and power-on-hour impacts.

J6eco-evm dts file already considers this, however j6evm-dts file needs
to be fixed to consider this constraint of the SoC.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add MMC1 and 2 nodes. MMC1 is SDcard and MMC2 is eMMC.

NOTE on MMC1 card detect: Ideally, we should be using in-built SDCD
support, but we dont have it yet. So, use the fact that control module
of DRA7 is setup such that no matter what mode one configures it, GPIO
option is always hardwired in - use GPIO mode for SDcard detection.

[peter.ujfalusi@ti.com]
The power line feeding the SD card is also used by other devices on the EVM.
Use generic name instead of mmc2_3v3 so when other devices want to use the
same regulator it will look a bit better.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

With Commit adff5962 ("Input: introduce palmas-pwrbutton"), we can
now support tps power button as a event source - This is SW7 (PB/WAKE)
on the J6-evm.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Even thought sys_nirq1 is hardwired on the SoC for the pin, it is
better to configure the pin to the required mux configuration.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The ldo4_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add USB data and pinctrl for USB.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The 4th USB controller instance present only on the DRA74x family of
devices so move it there.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA72-evm has a 256MB 16-bit wide NAND chip. Add
pinmux and NAND node.

The NAND chips 'Chip select' and 'Write protect' can be
controlled using DIP Switch SW5. To use NAND,
the switch must be configured like so:

SW5.1 (NAND_SELn) = ON (LOW)
SW5.9 (GPMC_WPN) = OFF (HIGH)
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Tested-by: NNishanth Menon <nm@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding CPSW phy-id, CPSW and MDIO pinmux configuration for active and
sleep states and enable them in board evm dts file.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add CPSW and MDIO related device tree data for DRA7XX and made as status
disabled. Phy-id, pinmux for active and sleep state needs to be added in
board dts files and enable the CPSW device.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.
Signed-off-by: NMarek Belisko <marek@goldelico.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add DSS related pinmux and display data nodes required to support
DVI video out on SBC-T3530, SBC-T3730 and SBC-T3517.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cc: devicetree@vger.kernel.org
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cc: devicetree@vger.kernel.org
Reviewed-by: NTony Lindgren <tony@atomide.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The '#mbox-cells' property is added to all the OMAP mailbox
nodes. This property is mandatory with the new mailbox framework.

Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the interrupts property to all the 13 mailbox nodes in
DRA7xx. The interrupts property information added is inline
with the expected values with the DRA7xx crossbar driver,
and is common to both DRA74x and DRA72x SoCs.

Do note that the mailbox 1 is only capable of generating out
3 interrupts, while all the remaining mailboxes have 4
interrupts each.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Looks like we have some GPMC NAND timings missing device
width. This fixes "gpmc_cs_program_settings: invalid width 0!"
errors during boot.
Signed-off-by: NTony Lindgren <tony@atomide.com>

With the GPMC warnings now enabled, I noticed the LAN9220 timings
can overflow the GPMC registers with 200MHz L3 speed. Earlier we
were just skipping the bad timings and would continue with the
bootloader timings. Now we no longer allow to continue with bad
timings as we have the timings in the .dts files.

We could start using the GPMC clock divider, but let's instead
use the u-boot timings that are known to be working and a bit
faster. These are basically the u-boot NET_GPMC_CONFIG[1-6]
defines deciphered. Except that we don't set gpmc,burst-length
as that's only partially configured and does not seem to work
if fully enabled.

[tony@atomide.com: updated to remove gpmc,burst-length]
Signed-off-by: NTony Lindgren <tony@atomide.com>

The four port serial port on the zoom debug board uses a TL16CP754C
with a single interrupt and GPMC chip select. The serial ports each
use a 8 bytes for IO registers, and are 256 bytes apart on the GPMC
line.

Let's add timings for all four ports so we can remove the GPMC
workarounds for using bootloader timings.

Not caused by this patch, but looks like u-boot only properly
initializes the fifo on the first serial port. Currently the other
ports produce garbage at least with my version of u-boot. I suspect
that TL16CP754C needs non-standard initialization added to 8250
driver to properly fix this issue.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Let's use the bootloader values except for the partially configured
wait-pin that does not seem to work.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GPMC binding is obviously very confusing as the values
are all over the place. People seem to confuse the GPMC partition
size for the chip select, and the device IO size within the GPMC
partition easily.

The ranges entry contains the GPMC partition size. And the
reg entry contains the size of the IO registers of the
device connected to the GPMC.

Let's fix the issue according to the following table:

Device          GPMC partition size     Device IO size
connected       in the ranges entry     in the reg entry

NAND            0x01000000 (16MB)       4
16550           0x01000000 (16MB)       8
smc91x          0x01000000 (16MB)       0xf
smc911x         0x01000000 (16MB)       0xff
OneNAND         0x01000000 (16MB)       0x20000 (128KB)
16MB NOR        0x01000000 (16MB)       0x01000000 (16MB)
32MB NOR        0x02000000 (32MB)       0x02000000 (32MB)
64MB NOR        0x04000000 (64MB)       0x04000000 (64MB)
128MB NOR       0x08000000 (128MB)      0x08000000 (128MB)
256MB NOR       0x10000000 (256MB)      0x10000000 (256MB)

Let's also add comments to the fixed entries while at it.
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Apparently some versions of nolo don't mux the all the necessary GPMC
pins for the smc91x probe to work properly. Let's fix this issue
by adding mux support for GPMC to the kernel.

Note that GPMC clk needs input enabled for OnenNAND to work.

Cc: Kevin Hilman <khilman@kernel.org>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 78b81f46 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:

- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command

In many times the audio card cannot be probed, which causes playback to fail.

After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.

This reverts commit 78b81f46.

Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Fix a typo error, the "emi" names refer to the eim clocks.

The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.
Signed-off-by: NOlof Johansson <olof@lixom.net>

I missed in 9a2ad529 that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Without the 3.3V regulator node, the SDMMC driver will give these warnings:

dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found

This patch adds the regulator node, and points the SD/MMC to the regulator.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
    "always-on"
v2: Move the regulator nodes to their respective board dts file and
    correctly rename them to match the schematic

Without this patch, the booting the SOCFPGA platform would hang at the
SDMMC driver loading. The issue, debugged by Doug Anderson, turned out
to be that the GPIO bank used by the SD card-detect was not set to
status="okay".

Also update the cd-gpios to point to portb of the &gpio1 GPIO IP.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Use &gpio1 to set status="okay" and update cd-gpio=&portb
v3: Correctly degugged the issue to be a gpio node not having status="okay"

Since the Synopsys GPIO IP can support multiple ports of varying widths, it
would make more sense to have the GPIO node DTS entry as this:

gpio0: gpio@ff708000{
	porta{
	};
};

Also, this is documented in the snps-dwapb-gpio.txt.
Suggested-by: NDoug Anderson <dianders@chromium.org>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.

This fixes USB.
Reported-by: NAndreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NAndreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

When CPU1 is brought out of reset, it's MMU is not turned on yet, so it will
only be able to use physical addresses. For systems with that have the
MMU page configured for 0xC0000000, 0x80000000, or 0x40000000
"BIC 0x40000000" will work just fine, as it was just converting the
virtual address of &cpu1start_addr into a physical address, ie. 0xC0000000
became 0x80000000. So for systems where the SDRAM controller was able to do a
wrap-around access, this was working fine, as it was just dropping the MSB,
but for systems where out of bounds memory access is not allowed, this would
not allow CPU1 to correctly fetch &cpu1start_addr.

This patch fixes the secondary_trampoline code to correctly fetch the
physical address of cpu1start_addr directly. The patch will subtract the
correct PAGE_OFFSET from &cpu1start_addr. And since on this platform, the
physical memory will always start at 0x0, subtracting PAGE_OFFSET from
&cpu1start_addr will allow CPU1 to correctly fetch the value of cpu1start_addr.

While at it, change the name of cpu1start_addr to socfpga_cpu1start_addr
to avoid any future naming collisions for multiplatform image.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Updated commit log to correctly lay out the usage of PAGE_OFFSET and
    add comments to the same effect.
v3: Used PAGE_OFFSET to get the physical address
v2: Correctly get the physical address instead of just a BIC hack.

Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

sed -i 's/}\ ;/};/g'
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add the cadence watchdog node to the Zynq devicetree.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing reference for memory-controller.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add missing reference for ADC node.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

By in sync with others node and add also baseaddr
to the node name.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>