Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently we try to open an aggregation for every packet (given that one
is not already open).

This causes redundant overhead (addba/delba) for null data packets.

Do not open an aggregation for null data packets.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data.  This is
unnecessary, so it can be removed.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add 6 new 8265 series PCI IDs:
  - (0x24FD, 0x1130)
  - (0x24FD, 0x0130)
  - (0x24FD, 0x0910)
  - (0x24FD, 0x0930)
  - (0x24FD, 0x0950)
  - (0x24FD, 0x0850)

CC: <stable@vger.kernel.org> [4.6+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add 3 new 8260 series PCI IDs:
  - (0x24F3, 0x10B0)
  - (0x24F3, 0xD0B0)
  - (0x24F3, 0xB0B0)

CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.

This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.

In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).

We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
 1. An AC_BE queue
 2. Same AC queue
 3. Highest AC queue that is lower than new AC
 4. Any existing AC (there always is at least 1 DATA queue)

If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211().  Fortunately, it's
never used so we can just remove it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi().  So we can't call iwl_force_nmi() in a
timer context.  To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.

This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Instead of explicitly indicating the difference between just
DVM and MVM with an mvm_fw boolean change this to fw.type to
be more extensible and easier to understand.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since the values of this enum are used only internally,
we can let the compiler number them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.

Fixes: 585a6fcc ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a warning in case packet didn't end up in the HW
destined queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We now have 9000 devices that support multiple frames in
a single RB. Enable it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Somehow we ended up without leading spaces here, fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

I'm starting to take a more active role in the iwlwifi driver
maintainership.

Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Small change to make it clear that the default value is false.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When initializing RX we grab NIC access for every read and
write. This is redundant - we can just grab access once.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The RX queues have a shadow register for the write pointer
that enables updates without grabbing NIC access. Use them
instead of the periphery registers because accessing those
is much more expensive.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In non-shared queues, DQA requires re-configuring existing
queues to become aggregated rather than allocating a new
one. It also requires "un-aggregating" an existing queue
when aggregations are turned off.

Support this requirement for non-shared queues.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since msleep is based on jiffies, it can sleep for a long time.
Use usleep_range() instead to shorten the maximum time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Newer hardware generations will take longer to be accessible again
after reset, so we need to wait longer before continuing any flow
that did a reset.

Rather than make the wait time configurable, simply extend it for
all.

Since all of these code paths can sleep, use usleep_range() rather
than mdelay().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Devices supporting VHT 160MHz width are supporting also Short GI.
Turn on this capability in vht cap.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>