Because the sram function is used for both suspend to memory and the suspend
to standby mode, renaming is more elegant.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

To simply the PM code, the suspend to standby mode uses same sram function
as the suspend to memory mode, running in the internal SRAM, instead of the
respective code for each mode.

For the suspend to standby mode, the master clock doesn't switch to the slow
clock, and PLLA and the main oscillator doesn't turn off as well.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

To decrease the suspend time, move copying the sram function to the sram
initialization phase, instead of every time go to suspend.

In the meanwhile, substitute fncpy() for memcpy().

If there is no sram allocated for PM, the PM is not supported.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

To decrease the duplicated code, create the procedure
to contain both activing and exiting the sdram self-refresh mode.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Assume USB PLL and PLL B are already stopped before entering sleep mode.

Removed PLL B from slow clock code, all drivers are supposed to properly
unprepare clocks.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: NWenyou.Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: remove the warning printed in pm.c]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The slow clock always exists, selecting CONFIG_AT91_SLOW_CLOCK config
is unnecessary for the suspend to memory mode.
For this mode the master clock should always switch to the slow clock.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

To simply the PM config the CONFIG_AT91_SLOW_CLOCK option will be removed,
so move "select SRAM" from under AT91_SLOW_CLOCK, add "select SRAM if PM"
under SOC_AT91SAM9 and SOC_SAMA5
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The SLOWDOWN_MASTER_CLOCK definition is not used, remove the redundant code.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Since at91_pm_set_standby() will not be used out of the pm.c file,
change its attribute from extern to static, remove its declaration as well.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit 2b0ba96c ("net: phy: micrel: disable NAND-tree for KSZ8021,
KSZ8031, KSZ8051, KSZ8081") automated the NAND-tree mode deactivation
process, thus making this phy fixup useless.
Remove it along with the associated headers inclusion.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: remove selection of PHYLIB in at91 Kconfig]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

When compiling the kernel in thumb2 (CONFIG_THUMB2_KERNEL option activated), we
hit a compilation crash. The error message is listed below:

---8< -----
Error: cannot use register index with PC-relative addressing -- `str r0,.saved_lpr'
--->8----

Add the .arm directive in the assembly files related to power management.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18

The at91rm9200, at91sam9260, at91sam9261 and at91sam9263 SoCs have slightly
different UDC IPs.
Those differences were previously handled with cpu_is_at91xx macro which
are about to be dropped for multi-platform support, thus we need to
change compatible strings.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

There is no specific driver handling the AHB matrix, this is a simple syscon
device. the matrix is needed by several other drivers including the USB on some
SoCs (at91sam9261 for instance).
Without this definition, the USB will not work on these SoCs.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).

Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Because writing the MOR register requires the PASSWD(0x37),
if missed, the write operation will be aborted.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Linux may be used without MMU on atmel SoCs, fix debug in this configuration.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Since turning on idle-halt in commit fe46aa67 (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: NMichel Marti <mma@objectxp.com>
Acked-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

There is now only one defconfig for the at91rm9200 and at91sam9. Add ethernet
support for the at91rm9200.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Recent distributions and userspace tools after 2009/2010 depend on
the existence of /sys/class/block/, and will not work with this option enabled.
Signed-off-by: NAnthony Harivel <anthony.harivel@emtrion.de>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Corrected pins used by usart3.
Signed-off-by: NJonas Andersson <jonas@microbit.se>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

On some platforms, there are multiple SRAM nodes defined in the device tree but
some of them are disabled, leading to allocation failure. Try to find the first
enabled SRAM node and allocate from it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

at91rm9200 standby and suspend to ram has been broken since
00482a40. It is wrongly using AT91_BASE_SYS which is a physical address
and actually doesn't correspond to any register on at91rm9200.

Use the correct at91_ramc_base[0] instead.

Fixes: 00482a40 (ARM: at91: implement the standby function for pm/cpuidle)
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

The DDRSDR controller fails miserably to put LPDDR1 memories in
self-refresh. Force the controller to think it has DDR2 memories
during the self-refresh period, as the DDR2 self-refresh spec is
equivalent to LPDDR1, and is correctly implemented in the
controller.

Assume that the second controller has the same fault, but that is
untested.
Signed-off-by: NPeter Rosin <peda@axentia.se>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Removed timeout on XTAL, PLL lock and Master Clock Ready, hang if
something went wrong instead of continuing in unknown condition. There
is not much we can do if a PLL lock never ends, we are running in SRAM
and we will not be able to connect back the sdram or ddram in order to
be able to fire up a message or just panic.

As a bonus, not decounting the timeout register in slow clock mode
reduce cumulated suspend time and resume time from ~17ms to ~15ms.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: NWenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Enable support for shmobile platforms that became multi-platform aware.
Several non-critical drivers and subsystems are built as modules, to keep
kernel size reasonable.

Tested on:
  - r8a73a4/ape6evm:
      - U-Boot fails with "Error: unrecognized/unsupported machine ID",
      - kexec works.
  - r8a7740/armadillo:
      - Hermit boot loader fails (larger image, more memory corruption),
      - kexec works.
  - r8a7791/koelsch,
  - sh73a0/kzm9g:
      - zImage+DTB from U-Boot needs CONFIG_ARM_ATAG_DTB_COMPAT=n,
      - kexec works.
  - am335x/boneblack.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The Kconfig options for the asm9260 timer is wrong as it can be selected by
another platform with allyes config and thus leading to a compilation failure
as some non arch related code is pulled by the compilation.

Fix this by having the platform Kconfig to select the timer as it is done for
the others drivers.
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NOleksij Rempel <linux@rempel-privat.de>

Conflicts:
	drivers/clocksource/Kconfig

Fixes: http://bugs.elinux.org/issues/127

the bb.org community was seeing random reboots before this change.
Signed-off-by: NRobert Nelson <robertcnelson@gmail.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In commit 87517d26 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.

But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.

As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.

[1] - https://lkml.org/lkml/2015/2/2/187Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

SATA operation depends on PIPE3 PHY and if we want
to boot from SATA drives, we have to have the PIPE3 PHY
driver built-in.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Without this NAND doesn't work on most EVMs.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>