This fixes a build error on pxa25x processes with pxa2xx_udc and

        CONFIG_USB_ETH=m
        # CONFIG_USB_ETH_RNDIS is not set

The error is because on that CPU there's no status transfer support
except with RNDIS.  Workaround, enable the RNDIS support too.
Signed-off-by: NIan Campbell <icampbell@arcom.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

One debug message won't print the right value; OSDL bugid 4545.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch started life as as527, and was rediffed by me.

Since the IDE interface doesn't convey much information about types of
errors, many USB-IDE adapters report all low-level errors with SK = 0x04,
which is supposed to be used only for non-recoverable errors.  As a result
the SCSI midlayer doesn't retry the command.  But quite often a retry
would succeed, whereas an unnecessary retry doesn't really hurt anything.

This patch uses a recently-implemented flag to tell the SCSI midlayer that
such hardware errors should be retried.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch causes a port reset whenever there's a transport error or abort.
If that fails it reverts back to doing a mass-storage device reset.  It
started life as as497 and was rediffed by me.

This makes error recovery a lot quicker and more reliable.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch does two things to help reset recovery.  It started life as
as496 and was rediffed by me.

First, the patch checks the result of a CLEAR_HALT request and doesn't reset the
endpoint's data toggle unless the request succeeded.

Second, it reduces the timeout for a device reset from 20 seconds to 5
seconds.

If all goes well, then I've finally figured quilt out and this patch should
apply cleanly.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

up(&usblp->sem) was called twice in a row in this code path.
Signed-off-by: NDomen Puncer <domen@coderock.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: fix atiremote input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)

> On Sun, Apr 10, 2005 at 07:21:28PM +0600, Viktor A. Danilov wrote:
> >
> > PROBLEM: aiptek input doesn`t register `device` & `driver` section in sysfs (/sys/class/input/event#)
> > REASON: `dev` - field not filled...
> > SOLUTION: in linux/drivers/usb/input/aiptek.c write
> >       aiptek->inputdev.dev = &intf->dev;
> > before calling
> >       input_register_device(&aiptek->inputdev);

The following (tested) patch fixes the exact same issue with the ATI
Remote input driver.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added support for Creative WebCam Go Mini.
Camera has STV680 chip and just different Product ID(0x4007) and Vendor ID (0x041e).
Signed-off-by: NKiril Jovchev <jovchev@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initialize status fields in the read and write urbs to prevent a race
condition with open/read/close - open/write/close sequences.

Fixes bug #4432 at bugzilla.kernel.org
Signed-off-by: NAdam Oldham <oldhamca@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This provides declarations for new requests, descriptors, and bitfields as
defined in the Wireless USB 1.0 spec.  Device support will involve a new
"Wire Adapter" device class, connecting a USB Host to a cluster of wireless
USB devices.  There will be two adapter types:

  * Host Wireless Adapter (HWA):  the downstream link is wireless, which
    connects a wireless USB host to wireless USB devices (not unlike like
    a hub) including to the second type of adapter.

  * Device Wireless Adapter (DWA): the upstream link is wireless, for
    connecting existing USB devices through wired links into the cluser.

All wireless USB devices will need persistent (and secure!) key storage, and
it's probable that Linux -- or device firmware -- will need to be involved
with that to bootstrap the initial secure key exchange.

Some user interface is required in that initial key exchange, and since the
most "hands-off" one is a wired USB link, I suspect wireless operation will
usually not be the only mode for wireless USB devices.  (Plus, devices can
recharge batteries using wired USB...)  All other key exchange protocols need
error prone user interactions, like copying and/or verifying keys.

It'll likely be a while before we have commercial Wireless USB hardware,
much less Linux implementations that know how to use it.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The itd_patch() function is responsible for allocating entries in the
buffer page pointer list of the iTD.  Particularly, a new page pointer
is needed every time when buffer data crosses a page boundary.

However, there is a bug in the allocation logic: the function does not
allocate a new entry when the current transaction is the first
transaction in the iTD (as indicated by first!=0).

The consequence is that, when the data of the first transaction begins
somewhere at the end of a page so that it actually does cross the page
boundary, no new page pointer is allocated.  This means that the data
at the end of the first transaction (beyond the page boundary) will be
accessed by the HC using the second page pointer, which is zero.
Furthermore, the first page pointer will be later overwritten by the
page pointers of the other transactions, which will garble it because
the value is or-ed into the iTD field.

All this particular check (for !first) does is cause incorrect
behaviour, so it should be entirely removed (and with it the variable
first that is not used for anything else).
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch changes the way uhci-hcd detects valid ports.  The
specification doesn't mention any way to find out how many ports a
controller has, so the driver has to use some heuristics, reading the port
status and control register and deciding whether the value makes sense.
With this patch the driver will recognize a typical failure mode (all bits
set to one) for nonexistent ports and won't assume there are always at
least 2 ports -- such an assumption seems silly if the heuristics have
already shown that the ports don't exist.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drain the rndis response queue on disconnect.  This fixes a problem
in which an rndis response left in the queue from a previous session
could cause a subsequent session to fail.
Signed-off-by: NAndy Lowe <alowe@mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes a compile glitch with CONFIG_USB_ETH_RNDIS disabled, and
replaces some inline #ifdeffery (and other code) with inline functions
which can evaluate to constants.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support to dummy_hcd for suspending and resuming the root
hub and the emulated platform devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the byte-ordering issue for setup packets in the
dummy_hcd driver and cleans up a few things that sparse -Wbitwise
dislikes.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

you seem to have applied the original, not the new improved one with
whiter teeth that uses kcalloc instead of kmalloc + memset.  Here's a
patch that goes on top of the one you applied.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Work around the gcc-2.95.x macro expansion bug.

Cc: Duncan Sands <baldrick@free.fr>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Zero the entire instance, not just the struct usbatm_data head.
Make sure the just allocated urb is freed if we fail to allocate
a buffer.  Based on a patch by Stanislaw W. Gruszka.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Acked-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Reduce the number of "unknown vpi/vci" debug messages to (usually) at most
one per-urb, rather than one per-cell.  This is only an issue when (a) many
packets come in but no connection is open; and (b) CONFIG_USB_DEBUG is set.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Makefile and Kconfig entries for the new drivers.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Doesn't do any firmware loading etc, just transmission and reception.
The user needs to take care of modem initialization, and load the
module with parameters giving the endpoints to use and so forth.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Driver for modems based on the Conexant AccessRunner chipset.
Original patch by Josep Comas, much reworked by Roman Kagan.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Port the speedtch driver to the new usbatm core.  The code is much
the same as before, just reorganized, though I threw in some minor
improvements (a new module parameter for choosing the altsetting,
more robust urb failure handling, ...) while I was there.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Rework the core usbatm code: minidrivers (i.e. drivers for particular
modems) now register themselves with the usbatm core, supplying methods
for binding/unbinding etc.  The design was inspired by usb-serial and
usbnet.  At the same time, more common code from the speedtch and
cxacru (patch 3/5) drivers was generalized and moved into the core.  The
transmission and reception parts have been unified and simplified.  Since
this is a major change and I don't like underscores in file names,
usb_atm.[ch] has been renamed usbatm.[ch].

Many thanks to Roman Kagan, who did a lot of the coding.
Signed-off-by: NDuncan Sands <baldrick@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Various minor EHCI updates

   * Dump some more info in the debug dumps, notably the product
     description (e.g. chip vendor), BIOS handhake flags, and
     debug port status (when it's not managed by the HCD).

   * Minor updates to the BIOS handoff code:  always flag the HCD
     as owned by Linux (in case BIOS doesn't grab it "early"),
     and on the buggy-BIOS path always match the "early handoff"
     code and forcibly disable SMI IRQs.

   * For the disabled 64bit DMA support, there's now a constant
     to use for the mask; use it.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This has several small updates to the px2xx UDC driver:

  * small fixes from Eugeny S. Mints <emints@ru.mvista.com>
     - local_irq_save() around potential endpoint disable race
     - fix handling of enqueue to OUT endpoints (potential oops)
  * add shutdown() method to disable any D+ pullup
  * rename methods accessing raw signals, referencing the signals
  * describes itself as for "pxa25x", since pxa27x is different
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Sparse updates; and the API change for SETUP packets being in USB byteorder.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is mostly "sparse" related updates, one of which was a missing
le32_to_cpu() should have affected big-endian hardware.

Notable is the API change:  setup packets are now provided in USB
byte order.  This affects only big-endian hardware, and the gadget
drivers have been updated in a separate patch.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This updates most of the gadget framework to expect SETUP packets use
USB byteorder (matching the annotation in <linux/usb_ch9.h> and usage
in the host side stack):

  - definition in <linux/usb_gadget.h>
  - gadget drivers:  Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs.
  - dummy_hcd

It also includes some other similar changes as suggested by "sparse",
which was used to detect byteorder bugs.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This prevents gadget drivers from being selected when no controller has
been selected, by adding an additional boolean and depending on it.
It's mostly to help "allmodconfig".
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NFlorian Echtler  <echtler@fs.tum.de>
Signed-off-by: NAndreas Deresch <aderesch@fs.tum.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the dummy_hcd driver use emulated root-hub interrupts
instead of polling.  It's in the spirit of similar changes being made to
the other HCDs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds to the dummy_hcd driver a new routine for keeping track of
all changes in the state of the emulated USB link.  The logic is now kept
in one spot instead of spread around, and it's easier to verify and
update the code.  The behavior of the port features has been corrected in
a few respects as well (for instance, if the POWER feature is clear then
none of the other features can be set).

Also added is support for the (relatively new) _connect() and
_disconnect() calls of the Gadget API.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes the dummy_hcd driver create separate platform devices for
the emulated host controller and emulated device controller.  This gives a
more accurate simulation and will permit testing of situations where only
one of the two devices is suspended.

This also changes the name of the host controller platform device to match
the name of the driver.  That way the normal platform bus probe mechanism
will handle binding the driver to the device.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch makes some cosmetic changes to dummy_hcd:

	Minor alterations of comments and whitespace.

	Replace USB_PORT_FEAT_xxx with USB_PORT_STAT_xxx.  This is
	appropriate as the values are stored in a status variable
	and they aren't feature indices.  Also it allows the
	elimination of a bunch of awkward bit shift operations.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Partial OTG support for dummy_hcd, mostly as a framework for further work.
It emulates the new OTG flags in the host and peripheral frameworks, if
that option is configured.  But it's incomplete:

  - Resetting the peripheral needs to clear the OTG state bits;
    a second enumeration won't work correctly.

  - This stops modeling HNP right when roles should switch the first time.
    It should probably disconnect, then set the usb_bus.is_b_host and
    usb_gadget.is_a_peripheral flags; then it'd enumerate almost normally,
    except for the role reversal.  Roles could then switch a second time,
    back to "normal" (with those flags cleared).

  - SRP should be modeled as "resume from port-unpowered", which is
    a state that usbcore doesn't yet use.

HNP can be triggered by enabling the OTG whitelist and configuring a
gadget driver that's not in that list; or by configuring Gadget Zero
to identify itself as the HNP test device.
Sent-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

More omap_udc updates:

  * OMAP 1710 updates
      - new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT
      - new OTG bits affecting wakeup
  * Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in
    for under 1024 bytes (not "up to 1024 bytes")
  * Handle transceiver setup more intelligently
      - use transceiver whenever one's available; this can be handy
        for GPIO based, loopback, or transceiverless configs
      - cleanup correctly after the "unrecognized HMC" case
  * DMA performance tweaks
      - allow burst/pack for memory access
      - use 16 bit DMA access most of the time on TIPB
  * Add workarounds for some DMA errata (not observed "in the wild"):
      - DMA CSAC/CDAC reads returning zero
      - RX/TX DMA config registers bit 12 always reads as zero (TI patch)
  * More "sparse" warnings removed, notably "changing" the SETUP packet
    to return data in USB byteorder (an API change, null effect on OMAP
    except for these warnings).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some cleanup for the the Ethernet part of the Ethernet/RNDIS gadget driver:

  - Remove remnants of ancient endpoint init logic; this is simpler, clearer

  - Save a smidgeon of space in the object file

  - Get rid of some #ifdeffery, mostly by using some newish inlines

  - Reset more driver state as part of USB reset

  - Remove a needless wrapper around an RNDIS call

  - Improve and comment the status interrupt handling:
      * RNDIS sometimes needs to queue these transfers (rarely in normal
        cases, but reproducibly while Windows was deadlocking its USB stack)
      * Mark requests as busy/not

  - Enable the SET_NETDEV_DEV() call; sysfs seems to behave sanely now

This is a net shrink of source code.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>