Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

IP sends device configuration (see inet_fill_link_af) as an array
in the netlink information, but the indices in that array are not
exposed to userspace through any current santized header file.

It was available back in 2.6.32 (in /usr/include/linux/sysctl.h)
but was broken by:
  commit 02291680
  Author: Eric W. Biederman <ebiederm@xmission.com>
  Date:   Sun Feb 14 03:25:51 2010 +0000

    net ipv4: Decouple ipv4 interface parameters from binary sysctl numbers

Eric was solving the sysctl problem but then the indices were re-exposed
by a later addition of devconf support for IPV4

  commit 9f0f7272
  Author: Thomas Graf <tgraf@infradead.org>
  Date:   Tue Nov 16 04:32:48 2010 +0000

    ipv4: AF_INET link address family

Putting them in /usr/include/linux/ip.h seemed the logical match
for the DEVCONF_ definitions for IPV6 in /usr/include/linux/ip6.h
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rfc 4861 says the Redirected Header option is optional, so
the kernel should not drop the Redirect Message that has no
Redirected Header option. In this patch, the function
ip6_redirect_no_header() is introduced to deal with that
condition.
Signed-off-by: NDuan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>

commit fba87559 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow.  But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge in a fix for RX MAC address filter programming bug in the sfc
driver.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 58ad436f.

It turns out that the change introduced a potential deadlock
by causing a locking dependency with netlink's cb_mutex. I
can't seem to find a way to resolve this without doing major
changes to the locking, so revert this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PLL hang workaround is required only for AR9330 and
AR9340. This issue was first observed on an AP121 and the WAR
is enabled for AR9340 also (DB120 etc.), since it uses a PLL
design identical to AR9330. This is not required for AR9485 and AR9550.

Various bugs have been reported regarding this:

https://bugzilla.redhat.com/show_bug.cgi?id=997217
https://bugzilla.redhat.com/show_bug.cgi?id=994648

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k_htc adds padding between the 802.11 header and the payload during
TX by moving the header. When handing the frame back to mac80211 for TX
status handling the header is not moved back into its original position.
This can result in a too small skb headroom when entering ath9k_htc
again (due to a soft retransmission for example) causing an
skb_under_panic oops.

Fix this by moving the 802.11 header back into its original position
before returning the frame to mac80211 as other drivers like rt2x00
or ath5k do.
Reported-by: NMarc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Tested-by: NMarc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: NMarc Kleine-Budde <mkl@blackshift.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My current 3.11 fix:

commit 788f7a56
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date:   Thu Aug 1 12:07:55 2013 +0200

    iwl4965: reset firmware after rfkill off

broke rfkill notification to user-space . I missed that bug, because
I compiled without CONFIG_RFKILL, sorry about that.

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As Sergei Shtylyov explained in the #mipslinux IRC channel:
[Mon 2013-08-19 12:28:21 PM PDT] <headless> guys, are you sure it's not "DMA off stack" case?
[Mon 2013-08-19 12:28:35 PM PDT] <headless> it's a known stack corruptor on non-coherent arches
[Mon 2013-08-19 12:31:48 PM PDT] <DonkeyHotei> headless: for usb/ehci?
[Mon 2013-08-19 12:34:11 PM PDT] <DonkeyHotei> headless: explain
[Mon 2013-08-19 12:35:38 PM PDT] <headless> usb_control_msg() (or other such func) should not use buffer on stack. DMA from/to stack is prohibited
[Mon 2013-08-19 12:35:58 PM PDT] <headless> and EHCI uses DMA on control xfers (as well as all the others)
Signed-off-by: NDaniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to get an interface specification if we know it's the
wrong one.
Signed-off-by: NDaniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

my earlier patch "mac80211: change IBSS channel state to chandef"
created a regression by ignoring the channel parameter in
__ieee80211_sta_join_ibss, which breaks IBSS channel selection. This
patch fixes this situation by using the right channel and adopting the
selected bandwidth mode.

Cc: stable@vger.kernel.org
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

commit 385904f8 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time.  This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.

This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"

Cc: stable@vger.kernel.org # 3.10
Reported-by: NTom Gundersen <teg@jklm.no>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

IBSS needs to release the channel context when leaving
but I evidently missed that. Fix it.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
Regarding the iwlwifi bits, Johannes says:

"We revert an rfkill bugfix that unfortunately caused more bugs, shuffle
some code to avoid touching the PCIe device before it's enabled and
disconnect if firmware fails to do our bidding. I also have Stanislaw's
fix to not crash in some channel switch scenarios."

As for the mac80211 bits, Johannes says:

"This time, I have one fix from Dan Carpenter for users of
nl80211hdr_put(), and one fix from myself fixing a regression with the
libertas driver."

Along with the above...

Dan Carpenter fixes some incorrectly placed "address of" operators
in hostap that caused copying of junk data.

Jussi Kivilinna corrects zd1201 to use an allocated buffer rather
than the stack for a URB operation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

getsockopt PACKET_STATISTICS returns tp_packets + tp_drops. Commit
ee80fbf3 ("packet: account statistics only in tpacket_stats_u")
cleaned up the getsockopt PACKET_STATISTICS code.
This also changed semantics. Historically, tp_packets included
tp_drops on return. The commit removed the line that adds tp_drops
into tp_packets.

This patch reinstates the old semantics.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to fix a problem in the rtl8211 where the driver
wasn't properly enabled the interrupt on link change status.
it has to enable the ineterrupt on the bit 10 in the register 18
(INER).
Reported-by: NSharma Bhupesh <B45370@freescale.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Included change:
- Check if the skb has been correctly prepared before going on

Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in
Config5. This is necessary to preserve WOL state when the driver is
loaded. Although the r8168 vendor driver does not write Config5 (it has
been commented out), Hayes Wang from Realtek said that masking bits like
this is more sensible.
Signed-off-by: NPeter Wu <lekensteyn@gmail.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If via_ircc_open() fails, data structures of the driver left uninitialized,
but probe (via_init_one()) returns zero. That can lead to null pointer dereference
in via_remove_one(), since it does not check drvdata for NULL.

The patch implements proper error code propagation.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user turns off VNET_HDR support on the
macvtap device, there is no way to provide any
offload information to the user.  So, it's safer
to ignore offload setting then depend on the user
setting them correctly.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the user turns off IFF_VNET_HDR flag, attempts to change
offload features via TUNSETOFFLOAD do not work.  This could cause
GSO packets to be delivered to the user when the user is
not prepared to handle them.

To solve, allow processing of TUNSETOFFLOAD when IFF_VNET_HDR is
disabled.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In macvtap, tap_features specific the features of that the user
has specified via ioctl().  If we treat macvtap as a macvlan+tap
then we could all the tap a pseudo-device and give it other features
like SG and GSO.  Then we can stop using the features of lower
device (macvlan) when forwarding the traffic the tap.

This solves the issue of possible checksum offload mismatch between
tap feature and macvlan features.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent.

The "when" field must be set for such skb. It's used in tcp_rearm_rto
for example. If the "when" field isn't set, the retransmit timeout can
be calculated incorrectly and a tcp connected can stop for two minutes
(TCP_RTO_MAX).
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NAndrey Vagin <avagin@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are possible HW configurations in which PFs will have SR-IOV capability
but will have Max VFs set to 0 - this happens when there are Multi-Function
devices where the VFs are allocated to only some of the PFs.

DMAE is configured to support VFs only if the configuring PF has supported VFs.
In case the first PF to be loaded will be one without supported VFs, it will
not configure DMAE to the VF-supporting mode. When VFs of other PFs will be
loaded later on, they will not be able to communicate with their PF.

This changes the requirement for configuring DMAE for VF-supporting mode;
If the device has SR-IOV capabilities there must be some PF that has
max supported VFs > 0, thus it will configure the DMAE for supporting VFs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since SR-IOV can be activated dynamically and iproute2 can be called
asynchronously, the various callbacks need a robust sanity check before
attempting to access the SR-IOV database and members since there are numerous
states in which it can find the driver (e.g., PF is down, sriov was not enabled
yet, VF is down, etc.).

In many of the states the callback result will be null pointer dereference.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During probe, VFs might erroneously try to access the shared memory (which
only PFs are capabale of accessing), causing benign attentions to appear.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When publishing information via getfeatcfg(), bnx2x driver didn't consider
remote errors (e.g., switch that doesn't support DCBX) when setting the
error flags.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After notification that DCBX configuration has ended arrived to the driver,
the driver configured the FW/HW in sleepless context.
As a result, it was possible to reach a race (mostly with CNIC registration)
in which the configuration will return a timeout, failing to set the DCBX
results correctly.

This patch moves the configuration following the DCBX end into the slowpath
RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the
configuration to cope with such races.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3deb8167 "bnx2x: Add a periodic task for link PHY events"
link state changes can be detected not only via the attention flow but also
from the periodic task.
If the link state will change in such a manner (i.e., via the periodic task),
dropless flow-control will not be configured.

This patch remedies the issue, adding the missing configuration to all required
flows.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not allowed for an ipv6 packet to contain multiple fragmentation
headers. So discard packets which were already reassembled by
fragmentation logic and send back a parameter problem icmp.

The updates for RFC 6980 will come in later, I have to do a bit more
research here.

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:

<http://seclists.org/oss-sec/2012/q4/292>

But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.

Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.

This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).

Thanks to Ding Tianhong to bring this topic up again.

Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: George Kargiotakis <kargig@void.gr>
Cc: P J P <ppandit@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the previous commit, Richard Genoud fixed proc_root_readdir(), which
had lost the check for whether all of the non-process /proc entries had
been returned or not.

But that in turn exposed _another_ bug, namely that the original readdir
conversion patch had yet another problem: it had lost the return value
of proc_readdir_de(), so now checking whether it had completed
successfully or not didn't actually work right anyway.

This reinstates the non-zero return for the "end of base entries" that
had also gotten lost in commit f0c3b509 ("[readdir] convert
procfs").  So now you get all the base entries *and* you get all the
process entries, regardless of getdents buffer size.

(Side note: the Linux "getdents" manual page actually has a nice example
application for testing getdents, which can be easily modified to use
different buffers.  Who knew? Man-pages can be useful)
Reported-by: NEmmanuel Benisty <benisty.e@gmail.com>
Reported-by: NMarc Dionne <marc.c.dionne@gmail.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Commit f0c3b509 ("[readdir] convert procfs") introduced a bug on the
listing of the proc file-system.  The return value of proc_readdir()
isn't tested anymore in the proc_root_readdir function.

This lead to an "interesting" behaviour when we are using the getdents()
system call with a buffer too small: instead of failing, it returns the
first entries of /proc (enough to fill the given buffer), plus the PID
directories.

This is not triggered on glibc (as getdents is called with a 32KB
buffer), but on uclibc, the buffer size is only 1KB, thus some proc
entries are missing.

See https://lkml.org/lkml/2013/8/12/288 for more background.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull gfs2 fixes from Steven Whitehouse:
 "Out of these five patches, the one for ensuring that the number of
  revokes is not exceeded, and the one for checking the glock is not
  already held in gfs2_getxattr are the two most important.  The latter
  can be triggered by selinux.

  The other three patches are very small and fix mostly fairly trivial
  issues"

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Check for glock already held in gfs2_getxattr
  GFS2: alloc_workqueue() doesn't return an ERR_PTR
  GFS2: don't overrun reserved revokes
  GFS2: WQ_NON_REENTRANT is meaningless and going away
  GFS2: Fix typo in gfs2_create_inode()

Pull x86 fixes from Ingo Molnar:
 "Two AMD microcode loader fixes and an OLPC firmware support fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, microcode, AMD: Fix early microcode loading
  x86, microcode, AMD: Make cpu_has_amd_erratum() use the correct struct cpuinfo_x86
  x86: Don't clear olpc_ofw_header when sentinel is detected