The patch fixes a critical issue to map txqid with flows on the hardware appropriately,
if tx queues created are more than flows configured then  txqid shall map within
the range of hardware flows configured. This ensure that un-mapped txqid does not remain un-handled.
The patch also segregated the rxqid and txqid for clarity.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Reviewed-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Save the filter tid while creating the server filter, which is used
later to retrieve the corresponding filter instance while handling
the filter reply.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are using the smallest padding boundary (8 bytes), which isn't
smaller than the Memory Controller Read/Write Size

We get best performance in 100G when the Packing Boundary is a multiple
of the Maximum Payload Size. Its related to inefficient chopping of DMA
packets by PCIe, that causes more overhead on bus. So driver is helping
by making the starting address alignment to be MPS size.

We will try to determine PCIE MaxPayloadSize capabiltiy  and set
IngPackBoundary based on this value. If cache line size is greater than
MPS or determinig MPS fails, we will use cache line size to determine
IngPackBoundary(as before).
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change t4fw_version.h to update latest firmware version
number to 1.16.33.0.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix typos and add the following to the scripts/spelling.txt:

  omited||omitted
  omiting||omitting

Link: http://lkml.kernel.org/r/1481573103-11329-26-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove variable rxq_info and also remove redundant assignment
to it.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make max number of supported tc u32 links equal to max number of filters
supported by hardware.
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For T6 adapters use T6 specific macro to set the force bit.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Acked-by: NJon Maxwell <jmaxwell37@gmail.com>
Acked-by: NJohannes Thumshirn <jth@kernel.org>
Acked-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.

Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without any uld being loaded, uld_txq_info[] will be NULL. uld_send()
is also used for sending control work requests(for eg: setting filter)
that dont require any ulds to be loaded. Hence move uld_txq_info[]
assignment after ctrl_xmit().

Also added a NULL check for uld_txq_info[].

Fixes: 94cdb8bb (cxgb4: Add support for dynamic allocation
       of resources for ULD).
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change assign flowc id to each outgoing request.Firmware use flowc id
to schedule each request onto HW. FW reply may miss without this change.
Reviewed-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Change t4fw_version.h to update latest firmware version
number 1.16.26.0.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two new variables are only used inside of an #ifdef and cause
harmless warnings when that is disabled:

drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c: In function 'init_one':
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:9: error: unused variable 'port_vec' [-Werror=unused-variable]
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:4646:6: error: unused variable 'v' [-Werror=unused-variable]

This adds another #ifdef around the declarations.

Fixes: 96fe11f2 ("cxgb4: Implement ndo_get_phys_port_id for mgmt dev")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform an emergency shutdown of the adapter and stop it from
continuing any further communication on the ports or DMA to the
host. This is typically used when the adapter and/or firmware
have crashed and we want to prevent any further accidental
communication with the rest of the world. This will also force
the port Link Status to go down -- if register writes work --
which should help our peers figure out that we're down.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The region set by the call to memset, immediately overwritten by
the subsequent call to memcpy and thus makes the  memset redundant.

Also remove the memset((&info, 0, sizeof(info)) on line 398 because
info is memcpy()'ed to before being used in the loop and it isn't
used outside of the loop.
Signed-off-by: NShyam Saini <mayhs11saini@gmail.com>
Reviewed-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not count pause frames as part of general TX/RX frame
counters.

Based on the original work of Casey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize mbox lock and list for mgmt dev to avoid NULL pointer
dereference when cxgb_set_vf_mac is called.

And also allocate memory for private data while allocating mgmt
netdev.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add port description for 25G and 100G cards, and also
change few port descriptions in compliance with the new
naming convention.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to report 25G and 100G links, which was missed
as part of commit "eb97ad99".
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The issue comes when there are multiple threads attempting to use
the mailbox facility at the same time.
When DCB operations and interface up/down is run in a loop for every
0.1 sec, we observed mailbox collisions. And out of the two commands
one would fail with the present code, since we don't queue the second
command.

To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at
the head issue the mailbox command, else wait for the existing command
to complete. Usually command takes less than a milli-second to
complete.

Also timeout from the loop, if the command under execution takes
long time to run.

In reality, the number of mailbox access collisions is going to be
very rare since no one runs such abusive script.
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

t6fw-1.15.15.0 enabled compressed error vector in cpl_rx_pkt for T6.
Updating driver to take care of these changes.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.
Requested-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

T6 adapters reduce number of completions to host by generating single
completion for all the directly placed(DDP) iSCSI pdus in a sequence.

This patch adds new structure for completion hw cmd (struct
cpl_rx_iscsi_cmp) and implements T6 completion feature.
Signed-off-by: NVarun Prakash <varun@chelsio.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NArjun V <arjun@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove deprecated module parameters num_vf, dflt_msg_enable and
force_init.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if txq_info->uldtxq cannot be allocated then
txq_info->txq is being kfree'd (which is redundant because it
is NULL) instead of txq_info. Fix this by instead kfree'ing
txq_info.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate resources dynamically for Upper layer driver's (ULD) like
cxgbit, iw_cxgb4, cxgb4i and chcr. The resources allocated include Tx
queues which are allocated when ULD register with cxgb4 driver and freed
while un-registering. The Tx queues which are shared by ULD shall be
allocated by first registering driver and un-allocated by last
unregistering driver.
Signed-off-by: NAtul Gupta <atul.gupta@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.

Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to release resources properly in error handling path of
alloc_uld_rxqs(), This patch also removes unwanted arguments
and avoids calling the same function twice.

Fixes: 94cdb8bb (cxgb4: Add support for dynamic allocation
       of resources for ULD
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.

acenic:
- min_mtu = 0, max_mtu = 9000

amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu

amd/xgbe:
- min_mtu = 0, max_mtu = 9000

sb1250:
- min_mtu = 0, max_mtu = 1518

cxgb3:
- min_mtu = 81, max_mtu = 65535

cxgb4:
- min_mtu = 81, max_mtu = 9600

cxgb4vf:
- min_mtu = 81, max_mtu = 65535

benet:
- min_mtu = 256, max_mtu = 9000

ibmveth:
- min_mtu = 68, max_mtu = 65535

ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu

jme:
- min_mtu = 1280, max_mtu = 9202

mv643xx_eth:
- min_mtu = 64, max_mtu = 9500

mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
  checks in the respective switch drivers' ndo_change_mtu functions

ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500

netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)

qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
  rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
  the value is 1500 or 9000

qualcomm/emac:
- min_mtu = 46, max_mtu = 9194

xilinx_axienet:
- min_mtu = 64, max_mtu = 9000

Fixes: 61e84623 ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not let number of offload queue sets to go more than
MAX_OFLD_QSETS, which would otherwise crash the driver
on machines with cores more than MAX_OFLD_QSETS.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A memory leak of qe occurs when t4_sched_queue_unbind fails,
so fix this by free'ing qe on the error exit path.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These accessors are used in various drivers that support tc offloading,
to detect properties of a given 'tc_action'.

'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR.
'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR.

As a prep towards supporting INGRESS redir/mirror, rename these
predicates to reflect their true meaning:
  s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/
  s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>