Update mfp setting for mmp2.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Since MFP_PIN_GPIO* now includes 128-255, mfp_to_gpio() is no longer
valid for those additional pins, fix it.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Add and initialize the mfp setting of pxa935 chip.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

There is currently an uncovered case for MFP configuration on PXAs which
is selected by setting the PULL_SEL bit but none of the PULL{UP,DOWN}_EN
bits. This case is needed to explicitly let pins float, even if the
selected alternate function would default to a configuration with a pull
resistor enabled.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NBin Yang <bin.yang@marvell.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NEric Miao <eric.miao@marvell.com>

When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.

Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.
Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There are two reasons for making the MFP configuration to be processor
independent, i.e. removing the relationship of configuration bits with
actual MFPR register settings:

   1. power management sometimes requires the MFP to be configured
      differently when in run mode or in low power mode

   2. for future integration of pxa{25x,27x} GPIO configurations

The modifications include:

1. introducing of processor independent MFP configuration bits, as
   defined in [include/asm-arm/arch-pxa/mfp.h]:

	bit  0.. 9 - MFP Pin Number (1024 Pins Maximum)
	bit 10..12 - Alternate Function Selection
	bit 13..15 - Drive Strength
	bit 16..18 - Low Power Mode State
	bit 19..20 - Low Power Mode Edge Detection
	bit 21..22 - Run Mode Pull State
	and so on,

2. moving the processor dependent code from mfp.h into mfp-pxa3xx.h

3. cleaning up of the MFPR bit definitions

4. mapping of processor independent MFP configuration into processor
   specific MFPR register settings is now totally encapsulated within
   pxa3xx_mfp_config()

5. using of "unsigned long" instead of invented type of "mfp_cfg_t"
   according to Documentation/CodingStyle Chapter 5, usage of this
   in platform code will be slowly removed in later patches
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pxa3xx_mfp_set_xxx() functions are originally provided for overwriting
MFP configurations performed by pxa3xx_mfp_config(), the usage of such
a dirtry trick is not recommended, since there is currently no user of
these functions, they are safely removed
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. update default MFPR value to drive strength fast 3mA and edge
   detection logic disabled

2. update impacted MFP_CFG_xxx() macros
Signed-off-by: Nbridge wu <bridge.wu@marvell.com>
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>