No need to have parentheses around plain pointer variable or
negation operator. Drop them for good.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's convenient to use get_unligned_beXX() and put_unaligned_beXX() helpers
to get or set MAC instead of open-coded variants.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conversion to devm_clk_get_optional() makes it explicit that clocks are
optional. This change allows to handle deferred probe in case clocks are
defined, but not yet probed. Due to above changes bail out in error case.

While here, check potential error when enable main clock.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is nothing which needs a set of OF headers, followed by redundant
OF node ID check. Drop them for good.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When compiled with CONFIG_ACPI=n, ACPI_PTR() will be no-op, and thus
genet_acpi_match table defined, but not used. Compiler is not happy about
such data. Drop ACPI_PTR() for good.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-04-20

This series includes misc updates and clean ups to mlx5 driver:

1) improve some comments from Hu Haowen.
2) Handles errors of netif_set_real_num_{tx,rx}_queues, from Maxim
3) IPsec and FPGA related code cleanup to prepare for ASIC devices
   IPsec offloads, from Raed
4) Allow partial mask for tunnel options, from Roi.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A barrier is needed here to ensure that rtl_tx sees the descriptor
changes (DescOwn set) before the updated tp->cur_tx value. Else it may
wrongly assume that the transfer has been finished already. For this
purpose smp_wmb() is sufficient.

No separate barrier is needed for ordering the descriptor changes
with the MMIO doorbell write. The needed barrier is included in
the non-relaxed writel() used by rtl8169_doorbell().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replaced "its" with "it's".
Signed-off-by: NHu Haowen <xianfengting221@163.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Embedded CPU bit doesn't change with PCI resume/suspend.
Hence read it only once while probing the PCI device.
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NBodong Wang <bodong@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

netif_set_real_num_tx_queues and netif_set_real_num_rx_queues may fail.
Now that mlx5e supports handling errors in the preactivate hook, this
commit leverages that functionality to handle errors from those
functions and roll back all changes on failure.
Signed-off-by: NMaxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

We use mapping to save and restore the tunnel options.
Save also the tunnel options mask.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In notify HW (ring doorbell) flow, we set the bit to request a completion
on the TX descriptor.
When doing so, we should not unset other bits in the same byte.
Currently, this does not fix a real issue, as we still don't have a flow
where both MLX5_WQE_CTRL_CQ_UPDATE and any adjacent bit are set together.

Fixes: 542578c6 ("net/mlx5e: Move helper functions to a new txrx datapath header")
Fixes: 864b2d71 ("net/mlx5e: Generalize tx helper functions for different SQ types")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently the SA handle is created and managed as part of the common
code for different IPsec supporting HW, this handle is passed to HW
to be used on Rx to identify the SA handle that was used to
return the xfrm state to stack.

The above implementation pose a limitation on managing this handle.

Refactor by moving management of this field to the specific HW code.

Downstream patches will introduce the Connect-X support for IPsec that
will use this handle differently than current implementation.
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NBoris Pismenny <borisp@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The current HW counters are supported only by Innova, split the ipsec
stats group into two groups, one for HW and one for SW. And expose
the HW counters to ethtool only if Innova HW is used for IPsec offload.
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently the FPGA IPsec is the only hw implementation of the IPsec
acceleration api, and so the mlx5_accel_esp_create_hw_context was
wrongly made to suit this HW api, among other in its parameter list
and some of its parameter endianness.

This implementation might not be suitable for different HW.

Refactor by group and pass all function arguments of
mlx5_accel_esp_create_hw_context in common mlx5_accel_esp_xfrm_attrs
struct field of mlx5_accel_esp_xfrm struct and correct the endianness
according to the HW being called.
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NBoris Pismenny <borisp@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The cited commit relies on include <net/geneve.h> being included
implicitly prior to include "en_accel/en_accel.h".
This mandates that all files that needs to include en_accel.h
to redantantly include net/geneve.h.

Include net/geneve.h explicitly at "en_accel/en_accel.h" to avoid
undesired constrain as above.

Fixes: e3cfc7e6 ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently the IPsec acceleration capability function is also used
at IPsec fpga capable device code.

This could cause a future bug as the acceleration layer is agnostic
to the device implementing its API.

Fix by using the IPsec FPGA capability function instead of acceleration
layer capability function in case of FPGA IPsec only related operations.

Downstream patches will add support for Connect-X IPsec, this can avoid
a future bug.
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NBoris Pismenny <borisp@mellanox.com>
Reviewed-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix the following coccicheck warning:

drivers/net/ethernet/qlogic/qed/qed_dev.c:4395:2-34: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qed/qed_dev.c:1975:2-34: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: NJason Yan <yanaijie@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Huazhong Tan says:

====================
net: hns3: misc updates for -next

This patchset includes some misc updates for the HNS3 ethernet driver.

[patch 1&2] separates two bloated function.
[patch 3-5] removes some redundant code.
[patch 6-7] cleans up some coding style issues.
[patch 8-10] adds some debugging information.

Change log:
V1->V2:	removes an unnecessary initialization in [patch 1] which
	suggested by David Miller.
	modified some print format issue and commit log in [patch 8].
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds trace event support for PF/VF mailbox.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for dumping MAC reg in debugfs,
which will be helpful for debugging.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds some debug information for failures of processing flow table,
removes the redundant printing when hclge_fd_check_spec() returns
error, and modifies the printing level for FD not enable error.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes some unnecessary blank lines, redundant
parentheses, and changes one tab to blank in
hclge_dbg_dump_reg_common().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hclge_set_fd_key_config(), parameter 'stage' should be
as enum HCLGE_FD_STAGE, and in hclge_config_key(), 'tuple_size'
should be type u8, also simplify unsigned int with u32 for 'i'.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct hclge_mac_vlan_remove_cmd and hclge_mac_vlan_add_cmd are unused.
So removes them from hclge_cmd.h.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

proto_support field in struct hclge_fd_cfg shows what protocols
in flow direct table are supported now. It is unnecessary since
checking which one is unsupported will be more efficient,
so this patch removes it.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since case default has included case 0, so removes this
redundant case 0.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_get_fd_rule_info() is bloated, this patch separates
it into several standalone functions for readability and
maintainability.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For readability and maintainability, this patch separates the
handling part of each flow type in hclge_fd_check_ether_tuple()
into standalone functions.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
RFC 2863 Testing Oper status

This patchset add support for RFC 2863 Oper status testing.  An
interface is placed into this state when a self test is performed
using ethtool.

v2:
Fix date/kernel version in Documentation
Add reviewed-by tags
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an interface is executing a self test, put the interface into
operative status testing.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to speed, duplex and dorment, report the testing status
in sysfs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RFC 2863 defines the operational state testing. Add support for this
state, both as a IF_LINK_MODE_ and __LINK_STATE_.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
FEC MDIO speedups

This patchset gives a number of speedups for MDIO with the FEC.
Replacing interrupt driven with polled IO brings a big speedup due to
the overheads of interrupts compared to the short time interval.
Clocking the bus faster, when the MDIO targets supports it, can double
the transfer rate. And suppressing the preamble, if devices support
it, makes each transaction faster.

By default the MDIO clock remains 2.5MHz and preables are used. But
these can now be controlled from the device tree. Since these are
generic properties applicable to more than just FEC, these have been
added to the generic MDIO binding documentation.

v2:
readl_poll_timeout()
Add patches to set bus frequency and preamble disable

v3:
Add Reviewed tags
uS->us
readl_poll_timeout_atomic()
Extend DT binding documentation
====================
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An MDIO transaction normally starts with 32 1s as a preamble. However
not all devices requires such a preamble. Add a device tree property
which allows the preamble to be suppressed. This will half the size of
the MDIO transaction, allowing faster transactions. But it should only
be used when all devices on the bus support suppressed preamble.
Suggested-by: NChris Healy <Chris.Healy@zii.aero>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: NChris Healy <Chris.Healy@zii.aero>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.

Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Suggested-by: NChris Heally <cphealy@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inline rtl8169_make_unusable_by_asic() and simplify it:
- Address field doesn't need to be poisoned because descriptor is
  owned by CPU now
- desc->opts1 is set by rtl8169_mark_to_asic() and rtl8169_rx_fill(),
  therefore we don't have to preserve any field parts.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl8169_mark_as_last_descriptor() has just one user, so inline it.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-04-19

This series contains updates to e1000e and igc only.

Sasha adds new device IDs supported by the igc driver.

Vitaly fixes the S0ix entry and exit flows in e1000e for TGP and newer
MAC types when a cable is connected.

Andre has the remaining changes in the series, starting with cleanup of
the igc driver of duplicate code.  Added a check for
IGC_MAC_STATE_SRC_ADDR flag which is unsupported for MAC filters in igc.
Cleaned up the return values for igc_add_mac_filter(), where the return
value was not being used, so update the function to only return success
or failure.  Fix the return value of igc_uc_unsync() as well.  Refactor
the igc driver in several functions to help reduce the convoluted logic
and simplify the driver filtering mechanisms.  Improve the MAC address
checks when adding a MAC filter.  Lastly, improve the log messages
related to MAC address filtering to ease debugging.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>