This reverts commit 3bae26eb2991c00670df377cf6c3bc2b0577e82a.

Seems it introduces regressions for 3 different reasons, oh boy..

In bug #90868 as I can see the atomic state will be restored on
resume without the planes being set up properly. Because plane
setup here requires the atomic state, we'll have to settle
for committing atomic planes first.

In bug #90861 the failure appears to affect mostly DP devices,
and happens because reading out the atomic state prevents a modeset
on boot, which would require better hw state readout.

In bug #90874 it's shown that cdclk should be part of the atomic
state, so only performing a single modeset during resume excarbated
the issue.

It's better to fix those issues first, and then commit this patch,
so do that temporarily.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90874Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.

We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.

It's required to revert this commit to revert the atomic hw
state readout patch.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This needs to be done last after all modesets have been calculated.

A modeset first disables all crtc's, so any crtc that undergoes a
modeset counts as inactive.

If no modeset's done, or > 1 crtc's stay w/a doesn't apply.
Apply workaround on the first crtc if 1 crtc stays active.
Apply workaround on the second crtc if no crtc was active.

Changes since v1:
 - Use intel_crtc->atomic as a place to put hsw_workaround_pipe.
 - Make sure quirk only applies to haswell.
 - Use first loop to iterate over newly enabled crtc's only.
   This increases readability.
Changes since v2:
 - Move hsw_workaround_pipe back to crtc_state.
Changes since v3:
 - Return errors from haswell_mode_set_planes_workaround.
Changes since v4:
- Clean up commit message.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.

Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.

Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Assume the callers lock everything with drm_modeset_lock_all.

This change had to be done after converting suspend/resume to
use atomic_state so the atomic state is preserved, otherwise
all transitional state is erased.

Now all callers of .crtc_enable and .crtc_disable go through
atomic modeset! :-D

Changes since v1:
- Only check for crtc_state->active in valleyview_modeset_global_pipes.
- Only check for crtc_state->active in modeset_update_crtc_power_domains.
Changes since v2:
- Rework on top of the changed patch order.
Changes since v3:
- Rename intel_crtc_toggle in description to *_control
- Change return value to int.
- Do not add plane state, should be done implicitly already.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

To make this work we load the new hardware state into the
atomic_state, then swap it with the sw state.

This lets us change the force restore path in setup_hw_state()
to use a single call to intel_mode_set() to restore all the
previous state.

As a nice bonus this kills off encoder->new_encoder,
connector->new_enabled and crtc->new_enabled. They were used only
to restore the state after a modeset.

Changes since v1:
- Make sure all possible planes are added with their crtc set,
  so they will be turned off on first modeset.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Now that we can subclass drm_atomic_state we can also use it to keep
track of all the pll settings. atomic_state is a better place to hold
all shared state than keeping pll->new_config everywhere.

Changes since v1:
- Assert connection_mutex is held.
Changes since v2:
- Fix swapped arguments to kzalloc for intel_atomic_state_alloc. (Jani Nikula)
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Having a single path for everything makes it a lot easier to keep
crtc_state->active in sync with intel_crtc->active.

A crtc cannot be changed to active when not enabled, because it means
no mode is set and no connectors are connected.

This should also make intel_crtc->active match crtc_state->active.

Changes since v1:
- Reworded commit message, there's no intel_crtc_toggle.
Changes since v2:
- Change some callers of intel_crtc_control to intel_display_suspend.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.

Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Now that the pll updates are staged the put_shared_dpll function
consists only of checks that are done in check_shared_dpll_state
after a modeset too.

The changes to pll->config are overwritten by
intel_shared_dpll_commit, so this entire function is a noop.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Bspec says we shouldn't enable IPS on BDW when the pipe pixel rate
exceeds 95% of the core display clock. Apparently this can cause
underruns.

There's no similar restriction listed for HSW, so leave that one alone
for now.

v2: Add pipe_config_supports_ips() (Chris)
v3: Compare against the max cdclk insted of the current cdclk
v4: Rebased to the latest
v5: Rebased to the latest
v6: Fix for patch style problems

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=83497Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The primary plane frobbing was removed from the sprite code in
 commit ecce87ea
 Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
 Date:   Tue Apr 21 17:12:50 2015 +0300

    drm/i915: Remove implicitly disabling primary plane for now

but the intel_flush_primary_plane() calls were left behind. Replace them
with straight forward POSTING_READ() of the sprite surface address
register.

The other user of intel_flush_primary_plane() is g4x_disable_trickle_feed()
where we can just inline the steps directly.

This allows intel_flush_primary_plane() to be killed off.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to re-init the display hardware when going out of suspend. This
includes:

  - Hooking the PCH to the reset logic
  - Restoring CDCDLK
  - Enabling the DDB power

Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:

  - DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
    of supported frequencies. As eDP also uses DPLL0 for its link rate,
    once DPLL0 is on, we restrict the possible eDP link rates the chosen
    VCO.
  - CDCLK also limits the bandwidth available to push pixels.

So, as a first step, this commit restore what the BIOS set, until I can
do more testing.

In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:

  #include <stdio.h>
  #include <stdint.h>
  #include <assert.h>

  #define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))

  static const struct dpll_freq {
          unsigned int freq;
          unsigned int decimal;
  } freqs[] = {
          { .freq = 308570, .decimal = 0b01001100111},
          { .freq = 337500, .decimal = 0b01010100001},
          { .freq = 432000, .decimal = 0b01101011110},
          { .freq = 450000, .decimal = 0b01110000010},
          { .freq = 540000, .decimal = 0b10000110110},
          { .freq = 617140, .decimal = 0b10011010000},
          { .freq = 675000, .decimal = 0b10101000100},
  };

  static void intbits(unsigned int v)
  {
          int i;

          for(i = 10; i >= 0; i--)
                  putchar('0' + ((v >> i) & 1));
  }

  static unsigned int freq_decimal(unsigned int freq /* in kHz */)
  {
          return (freq - 1000) / 500;
  }

  static void test_freq(const struct dpll_freq *entry)
  {
          unsigned int decimal = freq_decimal(entry->freq);

          printf("freq: %d, expected: ", entry->freq);
          intbits(entry->decimal);
          printf(", got: ");
          intbits(decimal);
          putchar('\n');

          assert(decimal == entry->decimal);
  }

  int main(int argc, char **argv)
  {
          int i;

          for (i = 0; i < ARRAY_SIZE(freqs); i++)
                  test_freq(&freqs[i]);

          return 0;
  }

v2:
  - Rebase on top of -nightly
  - Use (freq - 1000) / 500 for the decimal frequency (Ville)
  - Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
  - Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
    be consistent with the BXT code (Ville)
  - Store boot CDCLK in ddi_pll_init (Ville)
  - Merge dev_priv's skl_boot_cdclk into cdclk_freq
  - Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
  - Replace various '0' by SKL_DPLL0 to be a bit more explicit that
    we're programming DPLL0
  - Busy poll the PCU before doing the frequency change. It takes about
    3/4 cycles, each separated by 10us, to get the ACK from the CPU
    (Ville)

v3:
  - Restore dev_priv->skl_boot_cdclk, leaving unification with
    dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If the client stalls on a congested request, chosen to be 20ms old to
match throttling, allow the client a free RPS boost.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
[danvet: s/0/NULL/ reported by 0-day build]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we have internal clients, rather than faking a whole
drm_i915_file_private just for tracking RPS boosts, create a new struct
intel_rps_client and pass it along when waiting.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since we will often pageflip to an active surface, we will often have to
wait for the surface to be written before issuing the flip. Also we are
likely to wait on that surface in plenty of time before the vblank.
Since we have a mechanism for boosting when a flip misses the expected
vblank, curtain the number of times we RPS boost when simply waiting for
mmioflip.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: s/rq/req/]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The merged seqno->request conversion from John called request
variables req, but some (not all) of Chris' recent patches changed
those to just rq. We've had a lenghty (and inconclusive) discussion on
irc which is the more meaningful name with maybe at most a slight bias
towards req.

Given that the "don't change names without good reason to avoid
conflicts" rule applies, so lets go back to a req everywhere for
consistency. I'll sed any patches for which this will cause conflicts
before applying.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
[danvet: s/origina/merged/ as pointed out by Chris - the first
mass-conversion patch was from Chris, the merged one from John.]
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

As we perform the mmio-flip without any locking and then try to acquire
the struct_mutex prior to dereferencing the request, it is possible for
userspace to queue a new pageflip before the worker can finish clearing
the old state - and then it will clear the new flip request. The result
is that the new flip could be completed before the GPU has finished
rendering.

The bugs stems from removing the seqno checking in
commit 536f5b5e
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date:   Thu Nov 6 11:03:40 2014 +0200

    drm/i915: Make mmio flip wait for seqno in the work function
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Skylake nv12 format requires dbuf (aka. ddb) calculations
and programming for each of y and uv sub-planes. Made minor
changes to reuse current dbuf calculations and programming
for uv plane. i.e., with this change, existing computation
is used for either packed format or uv portion of nv12
depending on incoming format. Added new code for dbuf
computation and programming for y plane.

This patch is a pre-requisite for adding NV12 format support.
Actual nv12 support is coming in later patches.
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Currently vlv_wait_port_ready() waits for all four lanes on the
appropriate channel. This no longer works on CHV when the unused
lanes may be power gated. So pass in a mask of lanes that the
caller is expecting to be ready.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by:  Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is no longer necessary since we only update the staged config on
successfull modeset. The new configuration is stored in an atomic state
struct which is freed in case of failure.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This makes disabling planes more explicit.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
[anderco: fixed warning due to using drm_crtc instead of intel_crtc]
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

They're the same code, so why not?
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This was an optimization from way back before we had primary plane
support to be able to disable the primary plane. But with primary
plane support userspace can tell the kernel this directly, so there's
no big need for this any more. And it's getting in the way of the
atomic conversion.

If need be we can resurrect this later on properly again.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Explain why removing this is ok.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is used by the next commit to disable all planes on a crtc
without caring what type it is.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of the flags that were used are still useful when transitioning
to atomic, so keep those around for now. This removes some of the
complications of crtc->primary_enabled, making it easier to remove.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Updates the EDID compliance test function to perform the analyze and react to
the EDID data read as a result of a hot plug event. The results of this
analysis are handed off to userspace so that the userspace app can set the
display mode appropriately for the test result/response.

The compliance_test_active flag now appears at the end of the individual
test handling functions. This is so that the kernel-side operations can
be completed without the risk of interruption from the userspace app
that is polling on that flag.

V2:
- Addressed mailing list feedback
- Removed excess debug messages
- Removed extraneous comments
- Fixed formatting issues (line length > 80)
- Updated the debug message in compute_edid_checksum to output hex values
  instead of decimal
V3:
- Addressed more list feedback
- Added the test_active flag to the autotest function
- Removed test_active flag from handler
- Added failsafe check on the compliance test active flag
  at the end of the test handler
- Fixed checkpatch.pl issues
V4:
- Removed the checksum computation function and its use as it has been
  rendered superfluous by changes to the core DRM EDID functions
- Updated to use the raw header corruption detection mechanism
- Moved the declaration of the test_data variable here
V5:
- Update test active flag variable name to match the change in the
  first patch of the series.
- Relocated the test active flag declaration and initialization
  to this patch
V6:
- Updated to use the new flag for raw EDID header corruption
- Removed the extra EDID read from the autotest function
- Added the edid_checksum variable to struct intel_dp so that the
  autotest function can write it to the sink device
- Moved the update to the hpd_pulse function to another patch
- Removed extraneous constants
V7:
- Fixed erroneous placement of the checksum assignment. In some cases
  such as when the EDID read fails and is NULL, this causes a NULL ptr
  dereference in the kernel. Bad news. Fixed now.
V8:
- Updated to support the kfree() on the EDID data added previously
V9:
- Updated for the long_hpd flag propagation
V10:
- Updated to use actual checksum from the EDID read that occurs during
  normal hot plug path execution
- Removed variables from intel_dp struct that are no longer needed
- Updated the patch subject to more closely match the nature and contents
  of the patch
- Fixed formatting problem (long line)
V11:
- Removed extra debug messages
- Updated comments to be more informative
- Removed extra variable
V12:
- Removed the 4 bit offset of the resolution setting in compliance data
- Changed to DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER
Signed-off-by: NTodd Previte <tprevite@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a first of series patches that optimize DP link
training. The first patch is for eDP only where we reuse
the previously trained link training values from cache
i.e. voltage swing and pre-emphasis levels.

In case we are not able to train the link by reusing
the known values, the link training parameters are set
to zero and training is restarted.

V2:
- flag that indicates if DP link is trained and valid
  renamed from 'link_trained' to 'train_set_valid'
- removed routine 'intel_dp_reuse_link_train'

V3:
- rebased against the latest drm-intel-nightly

V4:
- removed HPD long pulse handling for eDP case to clear the
  flag that indicates to reuse the current link training
  parameters. (based on Sivakumar's comment)
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[danvet: s/DP/eDP/ in subject to make scope clear.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Inspired by scripts/coccinelle/api/err_cast.cocci
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Warn if the conditions to enter or exit DC5 are not satisfied such
as support for runtime PM, state of power well, CSR loading etc.

v2: Removed camelcase in functions and variables.

v3: Do some minimal check to assert if CSR program is not loaded.

v4:
1] Used an appropriate function lookup_power_well() to identify power well,
instead of using a magic number which can change in future.
2] Split the conditions further in assert_can_enable_DC5() and added more checks.
3] Removed all WARNs from assert_can_disable_DC5 as they were unnecessary and added two
   new ones.
4] Changed variable names as updated in earlier patches.

v5:
1] Change lookup_power_well function to take an int power well id.
2] Define a new intel_display_power_well_is_enabled helper function to check whether a
   particular power well is enabled.
3] Use CSR-related mutex in assert_csr_loaded function.

v6: Remove use of dc5_enabled variable as it's no longer needed.

v7:
1] Rebase to latest.
2] Move all DC5-related functions from intel_display.c to intel_runtime_pm.c.

v8: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)

v9: Modified below changes based on review comments from Imre.
- Moved intel_display_power_well_is_enabled() to intel_runtime_pm.c.
- Removed mutex lock from assert_csr_loaded(). (Animesh)

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Add triggers as per expectations mentioned in gen9_enable_dc5
and gen9_disable_dc5 patch.

Also call POSTING_READ for every write to a register to ensure that
its written immediately.

v1: Remove POSTING_READ calls as they've already been added in previous patches.

v2: Rebase to move all runtime pm specific changes to intel_runtime_pm.c file.

Modified as per review comments from Imre:
1] Change variable name 'dc5_allowed' to 'dc5_enabled' to correspond to relevant
   functions.
2] Move the check dc5_enabled in skl_set_power_well() to disable DC5 into
   gen9_disable_DC5 which is a more appropriate place.
3] Convert checks for 'pm.dc5_enabled' and 'pm.suspended' in skl_set_power_well()
   to warnings. However, removing them for now as they'll be included in a future patch
   asserting DC-state entry/exit criteria.
4] Enable DC5, only when CSR firmware is verified to be loaded. Create new structure
   to track 'enabled' and 'deferred' status of DC5.
5] Ensure runtime PM reference is obtained, if CSR is not loaded, to avoid entering
   runtime-suspend and release it when it's loaded.
6] Protect necessary CSR-related code with locks.
7] Move CSR-loading call to runtime PM initialization, as power domains needed to be
   accessed during deferred DC5-enabling, are not initialized earlier.

v3: Rebase to latest.

Modified as per review comments from Imre:
1] Use blocking wait for CSR-loading to finish to enable DC5  for simplicity, instead of
   deferring enabling DC5 until CSR is loaded.
2] Obtain runtime PM reference during CSR-loading initialization itself as deferred DC5-
   enabling is removed and release it at the end of CSR-loading functionality.
3] Revert calling CSR-loading functionality to the beginning of i915 driver-load
   functionality to avoid any delay in loading.
4] Define another variable to track whether CSR-loading failed and use it to avoid enabling
   DC5 if it's true.
5] Define CSR-load-status accessor functions for use later.

v4:
1] Disable DC5 before enabling PG2 instead of after it.
2] DC5 was being mistaken enabled even when CSR-loading timed-out. Fix that.
3] Enable DC5-related functionality using a macro.
4] Remove dc5_enabled tracking variable and its use as it's not needed now.

v5:
1] Mark CSR failed to load where necessary in finish_csr_load function.
2] Use mutex-protected accessor function to check if CSR loaded instead of directly
   accessing the variable.
3] Prefix csr_load_status_get/set function names with intel_.

v6: rebase to latest.
v7: Rebase on top of nightly (Damien)
v8: Squashed the patch from Imre - added csr helper pointers to simplify the code. (Imre)
v9: After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v10: Added a enum for different csr states, suggested by Imre. (Animesh)

v11: Based on review comments from Imre, Damien and Daniel following changes done
- enum name chnaged to csr_state (singular form).
- FW_UNINITIALIZED used as zeroth element in enum csr_state.
- Prototype changed for helper function(set/get csr status), using enum csr_state instead of bool.

v12: Based on review comment from Imre, introduced bool fw_loaded local to finish_csr_load() which helps
calling once to set the csr status. The same flag used to fail RPM if find any issue during
firmware loading.

Issue: VIZ-2819
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NSuketu Shah <suketu.j.shah@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.

This implementation is added based on first version of DMC CSR program
that we received from h/w team.

Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.

For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.

As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.

v1: Initial relese as RFC patch

v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.

v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.

v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.

v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.

Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.

v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.

v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.

v8: Rebase to latest.

v9: Rebase on top of -nightly (Damien)

v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)

v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)

v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)

v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)

v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)

v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)

v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)

Issue: VIZ-2569
Signed-off-by: NA.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NAnimesh Manna <animesh.manna@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch enables skylake primary plane scaling using shared
scalers atomic desgin.

v2:
-use single copy of scaler limits (Matt)

v3:
-move detach_scalers to crtc commit path (Matt)
-use values in plane_state->src as regular integers (me)

v4:
-changes to align with updated scaler structures (Matt, me)
-keep plane src rect in 16.16 format (Matt, Daniel)

v5:
-Rebased on top of 90/270 rotation changes (me)
-Fixed an issue introduced by 90/270 changes where plane programming
 is using drm_plane->state rect instead of intel_plane->state rect.
 This change also required for scaling to work properly. (me)
-With 90/270, updated limits to cover both portrait and landscape usages (me)
-Refactored skylake_update_primary_plane to reduce its size (Daniel)
 Added helper functions for refactoring are comprehended enough to be
 used for skylake_update_plane (for sprite) too. One stop towards
 having single function for all planes.

v6:
-Added fixme note when checking plane_state->src width in update_plane (Daniel)
-Release lock when failing to colorkey request with active scaler (Daniel)
Signed-off-by: NChandra Konduru <chandra.konduru@intel.com>
Reviewed-by: matthew.d.roper@intel.com
Reviewed-by: sonika.jindal@intel.com (v5)
Testcase: igt/kms_plane_scaling
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have grown a number of different implementations of
DIV_ROUND_CLOSEST_ULL throughout the kernel.  Move the i915 one to
kernel.h so that it can be reused.
Signed-off-by: NJavi Merino <javi.merino@arm.com>
Reviewed-by: NJeff Epler <jepler@unpythonic.net>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the skeleton framework for supporting automation for Displayport compliance
testing. This patch adds the necessary framework for the source device to
appropriately respond to test automation requests from a sink device.

V2:
- Addressed previous mailing list feedback
- Fixed compilation issue (struct members declared in a later patch)
- Updated debug messages to be more accurate
- Added status checks for the DPCD read/write calls
- Removed excess comments and debug messages
- Fixed debug message compilation warnings
- Fixed compilation issue with missing variables
- Updated link training autotest to ACK

V3:
- Fixed the checks on the DPCD return code to be <= 0
  rather than != 0
- Removed extraneous assignment of a NAK return code in the
  DPCD read failure case
- Changed the return in the DPCD read failure case to a goto
  to the exit point where the status code is written to the sink
- Removed FAUX test case since it's deprecated now
- Removed the compliance flag assignment in handle_test_request

V4:
- Moved declaration of type_type here
- Removed declaration of test_data (moved to a later patch)
- Added reset to 0 for compliance test variables

V5:
- Moved test_active variable declaration and initialization out of
  this patch and into the patch where it's used
- Changed variable name compliance_testing_active to
  compliance_test_active to unify the naming convention
- Added initialization for compliance_test_type variable
Signed-off-by: NTodd Previte <tprevite@gmail.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VSwing programming sequence as specified in the updated BXT BSpec

v2: Satheesh's review comments addressed.
- clear value before setting into registers
- move print statement to bxt function
Other changes
- since signal level will not be set into DDI_BUF_CTL, the value need
  not be returned to intel_dp_set_signal_levels(). Making the bxt
  specific function to return void and setting signal_levels = 0 for
  bxt inside intel_dp_set_signal_levels()
- instead of signal levels, printing vswing level and pre-emphasis
  level
- in case none of the pre-emphasis levels or vswing levels are set,
  setting default of 400mV + 0dB

v3: Satheesh's review comments
- Check for mask before printing signal_levels.
- Removing redundant register writes
- Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT
- Making register write part generic as it will be required for HDMI as
  well.

Re-structure the code to include an array for vswing related values, set
signal levels

v4: Satheesh's review comments
- Rebase over latest renaming patches
- use hsw_signal_levels for HAS_DDI
Other changes
- Modified vswing_sequence() func definition
- Rebased on top of register macro definitions

v5: Satheesh's review comments
- Check ddi translation table size

v6: Imre's review comments
- removed comments in vswing sequence
- added vswing, pre-emphasis prints in intel_dp_set_signal_levels
- added comment explaining use of DP vswing values for eDP
- initialize n_entries and ddi_transaltion table based on encoder type
- create bxt_ddi_buf_trans structure and use decimal values
- adding a flag in bxt buffer translation table to indicate def entry

v7: (imre)
- squash in Vandana's "VSwing register definition",
  "HDMI VSwing programming", "Re-enable vswing programming",
  "Fix vswing sequence" patches
- use BXT_PORT_* regs directly instead of via a temp var
- simplify BXT_PORT_* macro definitions
- add code comment why we read lane while write group registers
- fix readout of DP_TRAIN_PRE_EMPHASIS in debug message

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Assign PLL for pipe (dependent on port attached to the pipe)

v2:
- fix incorrect encoder vs. new_encoder check for crtc (imre)

v3:
- warn and return error if no encoder is attached (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't move intel_ddi_get_crtc_new_encoder around.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>